Surveying subsurface structure of soft ground using theSH‐wave seismic reflection method in combination with VSP

1984 ◽  
Author(s):  
Kunio Suyama ◽  
Tsuneo Imai ◽  
Hideo Ohtomo ◽  
Kenji Ohta ◽  
Yoshio Oishi
Geophysics ◽  
1992 ◽  
Vol 57 (10) ◽  
pp. 1373-1380 ◽  
Author(s):  
Richard D. Miller ◽  
Victor Saenz ◽  
Robert J. Huggins

The common‐depth‐point (CDP) seismic‐reflection method was used to delineate subsurface structure in a 3-m thick, 220-m deep coal zone in the Palau area of Coahuila, Mexico. An extensive series of walkaway‐noise tests was performed to optimize recording parameters and equipment. Reflection events can be interpreted from depths of approximately 100 to 300 m on CDP stacked seismic sections. The seismic data allow accurate identification of the horizontal location of the structure responsible for a drill‐discovered 3-m difference in coal‐zone depth between boreholes 150 m apart. The reflection method can discriminate folding with wavelengths in excess of 20 m and faulting with offset greater than 2 m at this site.


2008 ◽  
Author(s):  
Shunichiro Ito ◽  
Takao Aizawa ◽  
Fumio Nakada ◽  
Ryosuke Kitamura

1988 ◽  
Vol 59 (4) ◽  
pp. 141-150 ◽  
Author(s):  
John. L. Sexton

Abstract An important aspect of seismogenesis concerns the role of preexisting faults and other structural features as preferred zones of weakness in determining the pattern of strain accumulation and seismicity. Reactivation of zones of weakness by present day stress fields may be the cause of many intraplate earthquakes. To understand the relation between reactivated structures and seismicity, it is necessary to identify structures which are properly oriented with respect to the present-day stress field so that reactivation can occur. The seismic reflection method is very useful for identifying and delineating structures, particularly in areas where the structures are buried as in the New Madrid seismic zone. Application of the seismic reflection method in widely separated locations within the New Madrid rift complex has resulted in successful detection and delineation of reactivated rift-related structures which are believed to be associated with earthquake activity. The purpose of this paper is to discuss results from seismic reflection profiling in the New Madrid rift complex. Reflection data from several surveys including USGS Vibroseis* surveys in the Reelfoot rift area reveal reactivated faults and other deep rift-related structures which appear to be associated with seismicity. High-resolution explosive and Mini-Sosie** reflection surveys on Reelfoot scarp and through the town of Cottonwood Grove, Tennessee, clearly show reverse faults in Paleozoic and younger rocks which have been reactivated to offset younger rocks. A Vibroseis survey in the Wabash Valley area of the New Madrid rift complex provides direct evidence for a few hundred feet of post-Pennsylvanian age reactivation of large-offset normal faults in Precambrian-age basement rocks. Several earthquake epicenters have been located in the vicinity of these structures. In the Rough Creek graben, Vibroseis reflection data provide clear evidence for reactivation of basement faults. The success of these reflection surveys shows that well-planned seismic reflection surveys must be included in any program seeking to determine the relationship between preexisting zones of weakness and seismicity of an area.


1976 ◽  
Vol 16 (74) ◽  
pp. 73-88 ◽  
Author(s):  
Gilbert Dewart

AbstractIt appears to be possible to identify certain conditions of thermal regime at the base of a glacier through the seismic reflection method. In some cases layers of water or wet rock debris may be identifiable. The procedure is based upon the reversal of phase of reflected dilatational waves at the interface between ice and a substratum of lower acoustic impedance. Illustrations of the method are given from the west Antarctic ice sheet, and suggestions are made for the improvement of the technique.


Sign in / Sign up

Export Citation Format

Share Document