scholarly journals Radiation Effects on the Mechanical Properties and Microstructure of Type-304 Stainless Steel

1965 ◽  
Vol 1 (5) ◽  
pp. 462-477 ◽  
Author(s):  
J. S. Armijo ◽  
J. R. Low ◽  
U. E. Wolff
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Radiation Effects ◽  
304 Stainless Steel ◽  
Type 304 ◽  
Type 304 Stainless Steel

scholarly journals Pre-strain effect on the elevated temperature mechanical properties of type 304 stainless steel.

1986 ◽  
Vol 35 (398) ◽  
pp. 1284-1290 ◽  
Author(s):  
Kazuo OGAWA ◽  
Masaaki ISHII ◽  
Hiroyasu YOSHIZAWA ◽  
Satoshi OOTE ◽  
Yuhsaku WADA
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Elevated Temperature ◽  
304 Stainless Steel ◽  
Strain Effect ◽  
Type 304 ◽  
Type 304 Stainless Steel

A study on the numerical analysis of thermomechanical behaviour in a stud-to-plate laser braze joint

1999 ◽  
Vol 213 (8) ◽  
pp. 763-774 ◽  
Author(s):  
J-S Park ◽  
S-J Na
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Braze Alloy ◽  
Mechanical Analysis ◽  
304 Stainless Steel ◽  
Transient Temperature ◽  
Transfer Model ◽  
Thermomechanical Behaviour ◽  
Type 304 ◽  
Type 304 Stainless Steel

A mechanical analysis of stud-to-plate laser brazing was performed using the finite element method, and the transient displacement and stress fields in brazing workpieces were calculated. The materials used were small-diameter studs of AISI type 304 stainless steel, thin plates of Al 5052 aluminium and 88Al–12Si braze alloy for the filler metal. The mechanical analysis took account of the thermal aspects of brazing and the transient temperature fields were calculated using a brazing heat transfer model. An incremental plasticity model was employed for thermal elastoplastic analysis, which considered the temperature-dependent mechanical properties and the isotropic hardening effect of the materials. The numerical result showed that high residual tensile stresses remained in the middle of the braze gap, approaching the yield point of type 304 stainless steel. The permanent deformation of workpieces after the brazing was completed was minimal and confined to the area adjacent to the joint. Stress peaks were found to exist along the joining interfaces, which were due to mismatches in thermal and mechanical properties among the materials involved.

Mechanical properties of type 304 stainless steel sheet produced by twin-roll strip casting process

1993 ◽  
Vol 64 (2) ◽  
pp. 132-135 ◽  
Author(s):  
Hirohiko Takuda ◽  
Shiomi Kikuchi ◽  
Natsuo Hatta ◽  
Jun-ichi Kokado
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Steel Sheet ◽  
Casting Process ◽  
Strip Casting ◽  
304 Stainless Steel ◽  
Stainless Steel Sheet ◽  
Type 304 ◽  
Type 304 Stainless Steel ◽  
Twin Roll

TEM study of dislocation array/high angle grain boundary interaction in type 304 stainless steel

1986 ◽  
Vol 44 ◽  
pp. 586-587
Author(s):  
Cynthia M. Wise
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Grain Boundary ◽  
304 Stainless Steel ◽  
High Angle ◽  
Boundary Interaction ◽  
Solution Treated ◽  
Type 304 ◽  
Type 304 Stainless Steel ◽  
Standard Techniques

The interaction of dislocations with grain boundaries is considered a controlling process for many of the mechanical properties, including strength in a metal. The grain boundary acts as a barrier to impede the motion of dislocations, and strengthens the material because of the increased stress necessary to induce slip propagation.TEM samples were prepared from type 304 stainless steel which was solution treated, lightly deformed, electropolished using standard techniques, and examined in a JEOL 200CX TEM operating at 200KeV, using a double-tilt goniometer stage.

Sign in / Sign up

Export Citation Format

Share Document