Energy and Exergy Analysis on 350MW Combined Cycle Power Plant

2016 ◽  
Vol 12 (2) ◽  
Keyword(s):  
Power Plant ◽  
Exergy Analysis ◽  
Combined Cycle ◽  
Combined Cycle Power Plant ◽  
Energy And Exergy ◽  
Energy And Exergy Analysis

Energy and exergy analysis of a 747-MW combined cycle power plant Guddu

2018 ◽  
Vol 41 (13) ◽  
pp. 1495-1504 ◽  
Author(s):  
Mir Sikander Ali ◽  
Qadir Nawaz Shafique ◽  
Dileep Kumar ◽  
Summeet Kumar ◽  
Sanjay Kumar
Keyword(s):  
Power Plant ◽  
Exergy Analysis ◽  
Combined Cycle ◽  
Combined Cycle Power Plant ◽  
Energy And Exergy ◽  
Energy And Exergy Analysis

Multi-Point Energy and Exergy Analysis of a 1.5 MWe Hybrid SOFC-GT Power Plant

2006 ◽  
Author(s):  
Francesco Calise ◽  
Massimo Dentice d’Accadia ◽  
Laura Vanoli ◽  
Michael R. von Spakovsky
Keyword(s):  
Power Plant ◽  
Mass Flow ◽  
Heat Exchangers ◽  
Exergy Analysis ◽  
Pressure Ratio ◽  
Point Energy ◽  
Internal Reforming ◽  
Partial Load ◽  
Energy And Exergy ◽  
Energy And Exergy Analysis

This paper presents a multi-point energy and exergy analysis of a hybrid SOFC–GT power plant. The plant layout consists of the following principal components: an internal reforming SOFC, a steam-methane pre-reformer, a catalytic burner, a radial gas turbine, a centrifugal air compressor, a centrifugal fuel compressor, plate-fin heat exchangers, counter-flow shell and tube heat exchangers, and mixers. The partial load performance of the centrifugal compressors and radial turbine is determined using maps, properly scaled in order to match required mass flow rate and pressure ratio values. The plant is simulated on the basis of a zero-dimensional model discussed in previous papers. Two different partialization strategies are introduced in order to assess the partial load behavior of the plant. Results show that the plant achieves the best partial load performance for the case when both air and fuel mass flow rates are simultaneously reduced.

scholarly journals Energy and Exergy Analysis of Steam Power Plant 3rd Unit PT PLN (PERSERO) Centre Unit Generation Tanjung Jati B Use BFP-T Modification Cycle

2019 ◽  
Vol 125 ◽  
pp. 13003
Author(s):  
MSK. Tony Suryo U ◽  
Eflita Yohana ◽  
Syarif Dwi Priyanto ◽  
Ignatius Apryando M. ◽  
Tauviqirrahman
Keyword(s):  
Power Plant ◽  
Exergy Analysis ◽  
Energetic Efficiency ◽  
Exergetic Efficiency ◽  
Steam Power ◽  
Steam Power Plant ◽  
Operation Process ◽  
Energy And Exergy ◽  
Energy And Exergy Analysis ◽  
Long Operation

Steam power plant Generation of Tanjung Jati B 3rd unit has a capacity of 660 MW. The power plant operational in 2011, because of the long operation process, there will be a decrease in performance. The plant needs to be researched to analyze the performance and losses that occurs in the power plant. Because this also affects the environment if the efficiency of the power plant is high, it can reduce the use of coal. Because coal becomes air pollution and environmental pollution, which can cause acid rain, water pollution, and global warming. This research is used to analyze energy and exergy on the components of a steam power plant. From the results of this research, the largest of destruction exergy boiler is 881.08 MW and the exergetic efficiency is 48.66%. While the rate of the smallest destruction exergy in LPH 3 is 0.6 MW and the exergetic efficiency is 94.45%. The contribution of the largest Losses energy in the boiler is 231 MW and energetic efficiency is 87.05%. While the contribution of the smallest energy Losses in HPH 6 is 0.74 MW and energetic efficiency is 99.23%.

Sign in / Sign up

Export Citation Format

Share Document