scholarly journals Fabrikasi Prototipe Implan Tulang Maksilofasial sebagai Produk Implan Lokal

ROTASI ◽  
2019 ◽  
Vol 21 (4) ◽  
pp. 231
Author(s):  
Nanang Qosim
Keyword(s):  
Ultrasonic Cleaning ◽  
Micro Turning ◽  
Wire Cutting

Pasar alat kesehatan di Indonesia sejauh ini masih didominasi oleh produk-produk impor. Kelemahan utama produk impor bagi negara berkembang adalah harganya yang mahal. Oleh karena itu, lima tahun ke belakang para peneliti berkolaborasi dengan pihak industri dalam negeri menggencarkan pengembangan alat-alat kesehatan buatan dalam negeri. Riset ini bertujuan untuk mengembangkan produk implan maksilofasial berupa screw dan miniplate berbasis titanium sebagai produk alat biomedis buatan dalam negeri. Proses desain mengacu pada rekomendsi dari dokter spesialis bedah maksilofasial. Metode fabrikasi menggunakan proses micro turning untuk screw, sedangkan miniplate menggunakan wire cutting dan EDM. Selanjutnya, dilakukan pula proses deburring dan ultrasonic cleaning sebagai tahapan akhir. Hasil fabrikasi menunjukkan bahwa prototipe screw dan miniplate telah berhasil diproduksi dengan toleransi geometri yang dapat diterima sebagai sebuah produk implan.

scholarly journals A Dual Frequency Ultrasonic Cleaning Tank Developed by Transient Dynamic Analysis

2021 ◽  
Vol 11 (2) ◽  
pp. 699
Author(s):  
Worapol Tangsopa ◽  
Jatuporn Thongsri
Keyword(s):  
High Performance ◽  
Acoustic Pressure ◽  
Single Frequency ◽  
Response Analysis ◽  
Dual Frequency ◽  
Transient Dynamic Analysis ◽  
Ultrasonic Cleaning ◽  
Calculational Method ◽  
Successful Design ◽  
Harmonic Response Analysis

At present, development of manufacturer’s ultrasonic cleaning tank (UCT) to match the requirements from consumers usually relies on computer simulation based on harmonic response analysis (HRA). However, this technique can only be used with single-frequency UCT. For dual frequency, the manufacturer used information from empirical experiment alongside trial-and-error methods to develop prototypes, resulting in the UCT that may not be fully efficient. Thus, lack of such a proper calculational method to develop the dual frequency UCT was a problem that greatly impacted the manufacturers and consumers. To resolve this problem, we proposed a new model of simulation using transient dynamics analysis (TDA) which was successfully applied to develop the prototype of dual frequency UCT, 400 W, 18 L in capacity, eight horn transducers, 28 and 40 kHz frequencies for manufacturing. The TDA can indicate the acoustic pressure at all positions inside the UCT in transient states from the start to the states ready for proper cleaning. The calculation also reveals the correlation between the positions of acoustic pressure and the placement positions of transducers and frequencies. In comparison with the HRA at 28 kHz UCT, this TDA yielded the results more accurately than the HRA simulation, comparing to the experiments. Furthermore, the TDA can also be applied to the multifrequency UCTs as well. In this article, the step-by-step development of methodology was reported. Finally, this simulation can lead to the successful design of the high-performance dual frequencies UCT for the manufacturers.

Ultrasonic cleaning applications in dairies

2007 ◽  
Vol 109 (1) ◽  
pp. 31-42 ◽  
Author(s):  
Satu Salo ◽  
Gun Wirtanen
Keyword(s):  
Ultrasonic Cleaning

Study on the Characteristics of Oval Gear

2014 ◽  
Vol 633-634 ◽  
pp. 1100-1103
Author(s):  
Yong Ping Liu ◽  
Peng Wang ◽  
Xi Long Xian ◽  
Shi Yi Zhang
Keyword(s):  
Gear Tooth ◽  
Three Dimensional ◽  
Tooth Profile ◽  
Transmission Characteristics ◽  
Conversion Method ◽  
Wire Cutting ◽  
Oval Gear

For the problem of generating oval gear tooth profile and driving characteristic, desgin the tooth profile of oval gear by the conversion method of tooth profile, and get its three-dimensional modal by Pro/E. The transmission characteristics of a pair of ovate gear are researched; it would help to further study wire cutting of the oval gear based on the involute profile ,which got by the conversion of method of tooth profile, and the driving characteristic help to study other characteristics of oval gear as well as the application in the machinery.

Sign in / Sign up

Export Citation Format

Share Document