scholarly journals Hydrodynamic Effect on the Inhibition for the Flow Accelerated Corrosion of an Elbow

2017 ◽  
Vol 16 (1) ◽  
pp. 23-30 ◽  
Author(s):  
L. Zeng ◽  
G.A. Zhang ◽  
X.P. Guo
Keyword(s):  
Hydrodynamic Effect ◽  
Accelerated Corrosion ◽  
Flow Accelerated Corrosion

Influence of bend geometry on flow accelerated corrosion under neutral pH conditions

2021 ◽  
Vol 122 ◽  
pp. 105127
Author(s):  
P. Madasamy ◽  
M. Mukunthan ◽  
P. Chandramohan ◽  
T.V. Krishna Mohan ◽  
Andrews Sylvanus ◽  
...  
Keyword(s):  
Accelerated Corrosion ◽  
Neutral Ph ◽  
Ph Conditions ◽  
Flow Accelerated Corrosion

scholarly journals Flow-accelerated corrosion assessment for SA106 and SA335 pipes with elbows and welds

2021 ◽  
Author(s):  
Dong-Jin Kim ◽  
Sung-Woo Kim ◽  
Jong Yeon Lee ◽  
Kyung Mo Kim ◽  
Se Beom Oh ◽  
...  
Keyword(s):  
Accelerated Corrosion ◽  
Corrosion Assessment ◽  
Flow Accelerated Corrosion

Analytical Investigation of Deaerator Steam Inlet Nozzle Corrosion Allowance in a CANDU Station

2009 ◽  
Author(s):  
Ali Keshavarz ◽  
Andrew K. Ali ◽  
Randy K. Lall
Keyword(s):  
Finite Element ◽  
Carbon Steel ◽  
Stress Analysis ◽  
Analytical Investigation ◽  
Percentage Error ◽  
Metal Loss ◽  
Fe Model ◽  
Accelerated Corrosion ◽  
Materials Properties ◽  
Flow Accelerated Corrosion

Flow-accelerated corrosion (FAC) is a phenomenon that results in metal loss from piping, vessels and equipment made of carbon steel. This metal loss can lead to stress to occur at the steam inlet nozzle side, where it is located at the side of the deaerator. This paper presents a method to find the thickness critical of the steam inlet nozzle. A Finite Element (FE) model of the pressure vessel head was created to perform a stress analysis using NX Nastran 5.0. By applying materials properties, loads and constraints to the model, the results obtained are required to satisfy the following criterion: vonMises≥SySy=YieldStrength The results obtained from the stress analysis were analyzed to obtain a corrosion allowance and it was compared to the recommended value from a normal deaerator design, which is roughly 0.25 inches. From the FE model, and by continuously reducing the thickness of the nozzle, it was determined that the corrosion allowance is 0.229 inches, and that the percentage error was 8.4%.

Flow-accelerated corrosion behavior of 13Cr stainless steel in a wet gas environment containing CO2

2018 ◽  
Vol 25 (7) ◽  
pp. 779-787 ◽  
Author(s):  
Yong Li ◽  
Min-dong Chen ◽  
Jian-kuan Li ◽  
Long-fei Song ◽  
Xin Zhang ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Corrosion Behavior ◽  
Accelerated Corrosion ◽  
Wet Gas ◽  
Gas Environment ◽  
Flow Accelerated Corrosion

Techniques for Improved Reliability of Wall Thinning Estimation

2006 ◽  
Author(s):  
Yogendra S. Garud
Keyword(s):  
The Other ◽  
Remaining Life ◽  
Data Filtering ◽  
Large Database ◽  
Accelerated Corrosion ◽  
Wall Thinning ◽  
Simplified Method ◽  
Flow Accelerated Corrosion ◽  
The Impact ◽  
Thinning Rate

Wall thinning in pressure retaining components, especially due to the flow-accelerated corrosion, has been a significant factor affecting the safety and unplanned system downtimes. On the other hand, overestimating the impact of possible wall thinning often leads to unnecessary or expensive inspections and replacements. The simplified or quick (short-cut) methods of analysis and prediction often lack the requisite degree of accuracy and confidence. This paper presents a few techniques for better analysis of the wall thinning data to address these issues. These techniques make use of the statistical methods, pattern recognition, and optimization to perform a robust data filtering and thinning rate estimation that accounts for measurement uncertainty. The techniques are discussed with application to a large database and an inspection program. The impact of these analytical improvements is presented in comparison with results of the simplified method of analysis. The results include both the margin on remaining life and the projected wall thinning rates, with implications for inspections.

Flow and mass transfer downstream of an orifice under flow accelerated corrosion conditions

2012 ◽  
Vol 252 ◽  
pp. 52-67 ◽  
Author(s):  
Wael H. Ahmed ◽  
Mufatiu M. Bello ◽  
Meamer El Nakla ◽  
Abdelsalam Al Sarkhi
Keyword(s):  
Mass Transfer ◽  
Accelerated Corrosion ◽  
Flow Accelerated Corrosion
Sign in / Sign up

Export Citation Format

Share Document