Comparison of CANDU Fuel Bundle Finite Element Model with Unirradiated Mechanical Load Experiments

Author(s):  
Timothy J. Lampman ◽  
Adrian Popescu ◽  
Jose Freire-Canosa
2009 ◽  
Vol 6 (3) ◽  
pp. JAI101985
Author(s):  
Timothy J. Lampman ◽  
Adrian Popescu ◽  
Jose Freire-Canosa ◽  
Jeremy T. Busby ◽  
Brady Hanson ◽  
...  

2014 ◽  
Vol 5 (2) ◽  
pp. 175-188
Author(s):  
Gisèle Bihina ◽  
Bin Zhao ◽  
Abdelhamid Bouchaïr

The main results from a numerical investigation on a composite floor made of cellular beams at elevated temperatures are presented. From a full-scale natural fire test, a 3D finite element model has been developed under ANSYS code to simulate the thermo-mechanical behaviour of a composite floor with cellular beams. The calibration of this numerical model is based on the measured material properties and temperatures. A good correlation between the test and the numerical simulation is observed, in terms of temperatures, deformed shape and deflections. The finite element model is then used in a parametric study varying bay size, mechanical load and fire resistance rate. The results from this parametric study are compared to those from an analytical method, highlighting the conservativeness of the latter.


Author(s):  
Morakot Likhitpanichkul ◽  
X. Edward Guo ◽  
Van C. Mow

Under physiological loading, chondrocytes experience environmental changes due to complex mechanical and electrochemical events induced within cartilage. By mechanisms of cell-matrix interactions that remain unclear, chondrocytes perceive and respond to these events resulting in cascades of intracellular signals, and in turn alter their metabolic and biosynthesis activities. Chondrocyte deformation is a major cell response to mechanical load that has been proposed as a direct pathway for cell-matrix interaction and has been investigated in several studies [1–3]. However, the transient deformation of chondrocytes in situ, which is important in understanding the cell-matrix interaction under the viscoelastic response of cartilage, has not been well reported. In this study, we first aimed to measure and investigate the characteristics of the chondrocyte transient deformation within cartilage under the commonly-used unconfined compression test. We then aimed to model the cell inclusion within each specific cartilage specimen utilizing a multi-scale, triphasic finite element framework [4]. Finally the finite element model (FEM) will be used to calculate and perform parametric analyses of the cell transient deformation.


1989 ◽  
Vol 17 (4) ◽  
pp. 305-325 ◽  
Author(s):  
N. T. Tseng ◽  
R. G. Pelle ◽  
J. P. Chang

Abstract A finite element model was developed to simulate the tire-rim interface. Elastomers were modeled by nonlinear incompressible elements, whereas plies were simulated by cord-rubber composite elements. Gap elements were used to simulate the opening between tire and rim at zero inflation pressure. This opening closed when the inflation pressure was increased gradually. The predicted distribution of contact pressure at the tire-rim interface agreed very well with the available experimental measurements. Several variations of the tire-rim interference fit were analyzed.


1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.


Sign in / Sign up

Export Citation Format

Share Document