INVESTIGATION OF STRESSES IN THE THIN RIMMED SPUR GEAR TOOTH USING FEM

2013 ◽  
Vol 02 (11) ◽  
pp. 437-441
Author(s):  
Jaya.S.Kailuke .
Keyword(s):  
Gear Tooth ◽  
Spur Gear

Modeling of surface roughness in a novel magnetorheological gear profile finishing process

2020 ◽  
pp. 095440622097826
Author(s):  
Ravi Datt Yadav ◽  
Anant Kumar Singh ◽  
Kunal Arora
Keyword(s):  
Surface Roughness ◽  
Gear Tooth ◽  
Surface Characteristics ◽  
Spur Gear ◽  
Tooth Profile ◽  
Tooth Surface ◽  
Magnetic Flux Density ◽  
Element Analysis ◽  
Finishing Process ◽  
Gear Profile

Fine finishing of spur gears reduces the vibrations and noise and upsurges the service life of two mating gears. A new magnetorheological gear profile finishing (MRGPF) process is utilized for the fine finishing of spur gear teeth profile surfaces. In the present study, the development of a theoretical mathematical model for the prediction of change in surface roughness during the MRGPF process is done. The present MRGPF is a controllable process with the magnitude of the magnetic field, therefore, the effect of magnetic flux density (MFD) on the gear tooth profile has been analyzed using an analytical approach. Theoretically calculated MFD is validated experimentally and with the finite element analysis. To understand the finishing process mechanism, the different forces acting on the gear surface has been investigated. For the validation of the present roughness model, three sets of finishing cycle experimentations have been performed on the spur gear profile by the MRGPF process. The surface roughness of the spur gear tooth surface after experimentation was measured using Mitutoyo SJ-400 surftest and is equated with the values of theoretically calculated surface roughness. The results show the close agreement which ranges from −7.69% to 2.85% for the same number of finishing cycles. To study the surface characteristics of the finished spur gear tooth profile surface, scanning electron microscopy is used. The present developed theoretical model for surface roughness during the MRGPF process predicts the finishing performance with cycle time, improvement in the surface quality, and functional application of the gears.

Surface fitting of an involute spur gear tooth flank roughness measurement to its nominal shape

Measurement ◽  
2016 ◽  
Vol 91 ◽  
pp. 479-487 ◽  
Author(s):  
José A. Brandão ◽  
Jorge H.O. Seabra ◽  
Manuel J.D. Castro
Keyword(s):  
Gear Tooth ◽  
Spur Gear ◽  
Surface Fitting ◽  
Roughness Measurement ◽  
Tooth Flank

scholarly journals A Method of Selecting Grid Size to Account for Hertz Deformation in Finite Element Analysis of Spur Gears

1982 ◽  
Vol 104 (4) ◽  
pp. 759-764 ◽  
Author(s):  
J. J. Coy ◽  
C. Hu-Chih Chao
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Gear Tooth ◽  
Spur Gear ◽  
Grid Size ◽  
Spur Gears ◽  
Element Analysis ◽  
Element Size ◽  
Full Effect ◽  
The Finite Element Analysis

A method of selecting grid size for the finite element analysis of gear tooth deflection is presented. The method is based on a finite element study of two cylinders in line contact, where the criterion for establishing element size was that there be agreement with the classic Hertzian solution for deflection. Many previous finite element studies of gear tooth deflection have not included the full effect of the Hertzian deflection. The present results are applied to calculate deflection for the gear specimen used in the NASA spur gear test rig. Comparisons are made between the present results and the results of two other methods of calculation. The results have application in design of gear tooth profile modifications to reduce noise and dynamic loads.

Evaluation of Mechanical and Thermal Stresses in Polymer Gear Teeth through Simulation Approach

2013 ◽  
Vol 302 ◽  
pp. 468-473 ◽  
Author(s):  
Per Lindholm ◽  
Jian Qin
Keyword(s):  
Thermal Properties ◽  
Thermal Stresses ◽  
Material Selection ◽  
Gear Tooth ◽  
Gear Wheel ◽  
Spur Gear ◽  
Contact Forces ◽  
Mechanical And Thermal Properties ◽  
Gear Mesh ◽  
Tensional Stress

One way to achieve lightweight and lubricant-free drive train is, among others, to convert conventional steel to polymer composite materials. This paper describes a part of this endeavor by taking a spur gear pair as a study object. One of the steel gear wheel is replaced with three different materials including Victrex PEEK 650G, Victrex PEEK 650CA30 and Luvocom PEEK 1105-8165 while keeping the gear geometry unchanged. Mechanical stresses and thermal properties are two major criteria for material selection at this stage. Therefore carbon fiber filled PEEK (Victrex PEEK 650CA30) and PEEK filled with thermal conductive minerals (Luvocom 1105-8165) are chosen to benchmark each of the criterion. The evaluation is done by modeling the gear mesh and analyzing the contact forces and heat generated in the gear tooth. The results show surface temperature on the tooth flanks, root tensional stress and contact pressure during the tooth mesh. The work suggests a guideline of materials selection. Depending on actual application a compromisation between mechanical and thermal properties often needs to be considered within the tolerance boundary in order to obtain optimized results. This work only deals with material selection. Gear design such as optimization of tooth geometry for polymer gears is out of the scope of this study and will not be discussed.

scholarly journals Optimization of Tooth Root Profile Using Bezier Curve with G2 Continuity to Reduce Bending Stress of Asymmetric Spur Gear Tooth

2018 ◽  
Vol 237 ◽  
pp. 03010 ◽  
Author(s):  
Priyakant Vaghela ◽  
Jagdish Prajapati
Keyword(s):  
Stress Concentration ◽  
Gear Tooth ◽  
Spur Gear ◽  
Bézier Curve ◽  
Bezier Curve ◽  
Tooth Root ◽  
Geometric Continuity ◽  
Bending Stress ◽  
Gear Design ◽  
G2 Continuity

This research describes simple and innovative approach to reduce bending stress at tooth root of asymmetric spur gear tooth which is desire for improve high load carrying capacity. In gear design at root of tooth circular-filleted is widely used. Blending of the involute profile of tooth and circular fillet creates discontinuity at root of tooth causes stress concentration occurs. In order to minimize stress concentration, geometric continuity of order 2 at the blending of gear tooth plays very important role. Bezier curve is used with geometric continuity of order 2 at tooth root of asymmetric spur gear to reduce bending stress.

Sign in / Sign up

Export Citation Format

Share Document