scholarly journals Multi-Scale Numerical Modelling for Predicting Thermo-Physical Properties of Phase-Change Nanocomposites for Cooling Energy Storage

2021 ◽  
Vol 65 (2-4) ◽  
pp. 201-204
Author(s):  
Alessandro Ribezzo ◽  
Matteo Fasano ◽  
Luca Bergamasco ◽  
Luigi Mongibello ◽  
Eliodoro Chiavazzo
Keyword(s):  
Thermal Conductivity ◽  
Energy Storage ◽  
Phase Change ◽  
Phase Change Materials ◽  
Mean Field ◽  
Heat Transfer Process ◽  
Computational Time ◽  
Latent Heat Storage ◽  
Aspect Ratios ◽  
The Impact

One major limitation of phase-change materials (PCM) for thermal energy storage comes from their poor thermal conductivity hindering heat transfer process and power density. Nanocomposites PCMs, where highly conductive nanofillers are dispersed into PCM matrices, have been exploited in the past decades as novel latent heat storage materials with enhanced thermal conductivity. A computational model based on continuum simulations capable to link microscopic characteristics of nanofillers and the bulk PCM with the macroscopic effective thermal conductivity of the resulting nanocomposite is the aim of this work. After preliminary mean-field simulations investigating the impact of the nanofiller aspect ratio on the thermal conductivity of the nanocomposite, finite element simulations at reduced aspect ratios have been performed with corrected thermal conductivity values of the filler, to take into account the thermal interface resistances between fillers and matrix. Finally, the thermal conductivity at the actual aspect ratios has been extrapolated by the results obtained at reduced aspect ratios thus saving computational time and meshing efforts. This method has been validated through comparison against previous literature evidence and new experimental characterizations of nanocomposite PCMs.

scholarly journals Performance Improvement of a Household Refrigerator using Phase Change Material

2021 ◽  
Vol 16 (1) ◽  
pp. 032-041
Author(s):  
Pradeep N ◽  
Somesh Subramanian S
Keyword(s):  
Energy Storage ◽  
Phase Change ◽  
Phase Change Material ◽  
Phase Change Materials ◽  
Energy Savings ◽  
Storage System ◽  
Thermal Storage ◽  
Latent Heat Storage ◽  
Peak Loads ◽  
Change Material

Thermal energy storage through phase change material has been used for wide applications in the field of air conditioning and refrigeration. The specific use of this thermal storage has been for energy storage during low demand and release of this energy during peak loads with potential to provide energy savings due to this. The principle of latent heat storage using phase change materials (PCMs) can be incorporated into a thermal storage system suitable for using deep freezers. The evaporator is covered with another box which has storage capacity or passage through phase change material. The results revealed that the performance is increased from 3.2 to 3.5 by using PCM.

Solid/Liquid Phase Change Heat Transfer in Latent Heat Thermal Energy Storage

2009 ◽  
Author(s):  
D. Zhou ◽  
C. Y. Zhao
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Energy Storage ◽  
Phase Change ◽  
Calcium Chloride ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Phase Change Materials ◽  
Metal Foams ◽  
Chloride Hexahydrate

Phase change materials (PCMs) have been widely used for thermal energy storage systems due to their capability of storing and releasing large amounts of energy with a small volume and a moderate temperature variation. Most PCMs suffer the common problem of low thermal conductivity, being around 0.2 and 0.5 for paraffin and inorganic salts, respectively, which prolongs the charging and discharging period. In an attempt to improve the thermal conductivity of phase change materials, the graphite or metallic matrix is often embedded within PCMs to enhance the heat transfer. This paper presents an experimental study on heat transfer characteristics of PCMs embedded with open-celled metal foams. In this study both paraffin wax and calcium chloride hexahydrate are employed as the heat storage media. The transient heat transfer behavior is measured. Compared to the results of pure PCMs samples, the investigation shows that the additions of metal foams can double the overall heat transfer rate during the melting process. The results of calcium chloride hexahydrate are also compared with those of paraffin wax.

Latent Heat Storage: Container Geometry, Enhancement Techniques, and Applications—A Review

2019 ◽  
Vol 141 (5) ◽  
Author(s):  
S. Arunachalam
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Energy Storage ◽  
Phase Change ◽  
Latent Heat ◽  
Thermal Energy ◽  
Heat Exchangers ◽  
Phase Change Materials ◽  
Heat Storage ◽  
Low Thermal Conductivity

Energy storage helps in waste management, environmental protection, saving of fossil fuels, cost effectiveness, and sustainable growth. Phase change material (PCM) is a substance which undergoes simultaneous melting and solidification at certain temperature and pressure and can thereby absorb and release thermal energy. Phase change materials are also called thermal batteries which have the ability to store large amount of heat at fixed temperature. Effective integration of the latent heat thermal energy storage system with solar thermal collectors depends on heat storage materials and heat exchangers. The practical limitation of the latent heat thermal energy system for successful implementation in various applications is mainly from its low thermal conductivity. Low thermal conductivity leads to low heat transfer coefficient, and thereby, the phase change process is prolonged which signifies the requirement of heat transfer enhancement techniques. Typically, for salt hydrates and organic PCMs, the thermal conductivity range varies between 0.4–0.7 W/m K and 0.15–0.3 W/m K which increases the thermal resistance within phase change materials during operation, seriously affecting efficiency and thermal response. This paper reviews the different geometry of commercial heat exchangers that can be used to address the problem of low thermal conductivity, like use of fins, additives with high thermal conductivity materials like metal strips, microencapsulated PCM, composite PCM, porous metals, porous metal foam matrix, carbon nanofibers and nanotubes, etc. Finally, different solar thermal applications and potential PCMs for low-temperature thermal energy storage were also discussed.

Enhanced thermal conductivity of PEG/diatomite shape-stabilized phase change materials with Ag nanoparticles for thermal energy storage

2015 ◽  
Vol 3 (16) ◽  
pp. 8526-8536 ◽  
Author(s):  
Tingting Qian ◽  
Jinhong Li ◽  
Xin Min ◽  
Weimin Guan ◽  
Yong Deng ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Energy Storage ◽  
Phase Change ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Ag Nanoparticles ◽  
Phase Change Materials ◽  
Enhanced Thermal Conductivity

The thermal conductivity was 0.82 W m−1 K−1 for 7.2% AgNPs in PEG/diatomite, which was enhanced by 127% compared to PEG/diatomite.

Sign in / Sign up

Export Citation Format

Share Document