Hole Cleaning Optimization in Horizontal Wells: A New Method To Compensate Negative Hole Inclination Effects

Author(s):  
Nozar Malekzadeh ◽  
Mehdi Mohammadsalehi
1999 ◽  
Author(s):  
Jiang Shengzong ◽  
Wang Xilu ◽  
Cao Limin ◽  
Liu Kunfang
Keyword(s):  

Author(s):  
M. I. Epov ◽  
◽  
V. N. Glinskikh ◽  
M. N. Nikitenko ◽  
K. V. Sukhorukova ◽  
...  

The work is devoted to the substantiation of new geophysical technology for mapping the Bazhenovskaya Formation based on an impulsive electromagnetic sounding from wells. Theoretically shown the possibility of its application to study the formation from highly inclined and subhorizontal wells drilled in the Upper and Middle Jurassic formations. Numerical modeling of the signals in realistic geoelectric models of the Bazhenov Formation with real well trajectories is carried out on the example of the East Surgut field. The calculations have established that the determination of spatial locations of the top and bottom of the beds is possible when using different-length sondes. Zones of high sensitivity of the full magnetic field matrix to the boundaries with a sufficient signal level at considerable distance, even with a small sonde length, are determined. It is theoretically established that pulsed sounding of the Bazhenov Formation from the Upper and Middle Jurassic reservoirs is feasible for both mapping the boundaries of the formation and tracing its lateral variability.


Author(s):  
Evren M. Ozbayoglu ◽  
Flavio Rodrigues ◽  
Reza Ettehadi ◽  
Roland May ◽  
Dennis Clapper

Abstract As explorations advance and drilling techniques become more innovative, complex and challenging trajectories arise. In consequence, cuttings transport has continued to be a subject of interest because, if the drilled cuttings cannot be removed from the wellbore, drilling cannot proceed for long. Therefore, efficient cleaning of highly inclined and horizontal wellbores is still among the most important problems to solve, because these types of wells require specialized fluid formulations and/or specific hole cleaning techniques. There are numerous studies and methods that focus in cuttings transportation in highly inclined and horizontal wells. One of them is the use of viscosity and density sweeps. Sweep pills have been used in the drilling industry as a tool to improve hole cleaning. This report presents the analysis of the performance of different sweeps pills working independently and in tandem in polymeric, oil and synthetic based systems and the comparison between them. The main objective of this project is to provide experimental evidence on which types of fluids perform better under certain conditions by studying the effect of viscosity and density in the bed erosion process in highly inclined and horizontal wells. In order to achieve that, several fluid formulations were tested at different inclination angles (90, 75, 60 degrees) in the Small Indoor Flow Loop property of The University of Tulsa’s Drilling Research Projects. The results of the tests are presented in terms of volume of drilled cuttings removed from the test section and measured differential pressures. All the tests were conducted under atmospheric pressure and ambient temperature. Moreover, a 2-Layer model is used for estimating the erosion performance of sweeps for design purposes, and the model estimations are compared with experimental results. From the experiments, it was identified that polymeric, oil and synthetic based muds with similar density and rheological properties eroded and transported the drilled cuttings similarly under similar test conditions. Furthermore, pumping the sweep pills in tandem demonstrated higher cuttings transport efficiency when compared with the sweep pills applied independently.


1996 ◽  
Author(s):  
Hujun Li ◽  
Zhengqi Jia ◽  
Zhaosheng Wei

2021 ◽  
Author(s):  
Alexey Ruzhnikov ◽  
Edgar Echevarria

Abstract In the Middle East many of the matured fields have fractured or vugular formations where the drilling is continued without return to a surface. This situation has been commonly interpreted as lack of hole cleaning and high risk of stuck pipe. The manuscript describes a study performed to analyze the hole cleaning while blind drilling horizontal sections. Most of the losses while drilling across fractured or vugular formations happen sudden, and this represents a risk of formation instability and stuck pipe. Additionally, the cuttings accumulation may lead to a potential pack off. To understand the hole cleaning the annular pressure while drilling was introduced in different sections, what via change of the equivalent static and dynamic densities describes the cutting and cavings accumulation in the annulus. Additionally, the hole cleaning behavior with different fluids pumped through the drillstring (i.e. drilling fluid, water, water with sweeps) was studied. The proposed study was performed in 4 different fields, 9 wells, across horizontal 6⅛-in. sections with total lost circulation. It was identified that while drilling with full returns ECD vs ESD variations are within 1.5 ppg, those variations are matching with the modeling of hydraulics. Once total losses encountered the variations between ECD and ESD are very low - within 0.2 ppg - indicating that annular friction losses below the loss circulation zone are minimal. This support the theory that all the drilled cuttings are properly lifted from bottom and carried to the karst into the loss circulation zone and not fluctuating above the loss zone. Additionally, minor to no relation found in hole cleaning while drilling with mud or a water with sweeps. This finding also is aligned with the stuck pipe statistics that shows higher incidents of stuck pipe while drilling the with full circulation due to pack off. The manuscript confirms the theory of the hole cleaning in total lost circulation and application of different hole cleaning practices to improve it. The results of the study can be implemented in any project worldwide.


Author(s):  
S.I. Gabitova ◽  
L.A. Davletbakova ◽  
V.Yu. Klimov ◽  
D.V. Shuvaev ◽  
I.Ya. Edelman ◽  
...  

The article describes new decline curves (DC) forecasting method for project wells. The method is based on the integration of manual grouping of DC and machine learning (ML) algorithms appliance. ML allows finding hidden connections between features and the output. Article includes the decline curves analysis of two well completion types: horizontal and slanted wells, which illustrates that horizontal wells are more effective than slanted.


Geophysics ◽  
2010 ◽  
Vol 75 (3) ◽  
pp. SA37-SA43 ◽  
Author(s):  
Joongmoo Byun ◽  
Jeongmin Yu ◽  
Soon Jee Seol

Time-lapse crosswell seismic provides an efficient way to monitor the migration of a [Formula: see text] plume or its leakage after [Formula: see text] injection into a geologic formation. Recently, crosswell seismic has become a powerful tool for monitoring underground variations, using the concept of a virtual source, with virtual sources positioned at the receivers installed in the well and thus the positions of sources and receivers can be invariant during monitoring. However, time-lapse crosswell seismic using vertical wells and virtual sources has difficulty in describing the front of a [Formula: see text] plume, which usually is parallel to the vertical wells, and in obtaining sufficient ray coverage for the first-arrival tomography. These problems arise because of the theoretical downward-illumination-directivity limitation of the virtual source. We have developed an effective monitoring method that uses virtual sources and two horizontal wells: one above and one below the [Formula: see text]sequestration reservoir. In our method, we redatum the traces that are recorded at geophones in horizontal wells from sources on the surface. The redatumed traces then become virtual traces recorded at geophones in the lower well and sent from virtual sources at the positions of the geophones in the upper well. The geometry of our method has advantages for locating the front of the [Formula: see text] plume, which is normal to the horizontal wells, compared with either real or virtual sources. The method also is advantageous in acquiring full ray coverage between the wells, and that coverage is superior to coverage acquired using vertical crosswell seismic with virtual sources. In addition, we can avoid problems related to any potential change in the medium above the reservoir and in the source and receiver positions. The results of applying our method to synthetic data that simulate [Formula: see text]-sequestration monitoring show that the front of a [Formula: see text] plume in the reservoir is depicted accurately in a velocity tomogram. The new method also can be used to monitor a reservoir during production of heavy oil.


2020 ◽  
Author(s):  
Oliver Czuprat ◽  
Anne Marte Faugstad ◽  
Piotr Byrski ◽  
Kai Schulze

2016 ◽  
Vol 28 ◽  
pp. 347-355 ◽  
Author(s):  
Zhi-chuan Guan ◽  
Yu-ming Liu ◽  
Yong-wang Liu ◽  
Yu-qiang Xu

Sign in / Sign up

Export Citation Format

Share Document