Formation Heat Treatment (FHT): A State-of-the-art Technology For Near-wellbore Formation Damage Treatment

10.2118/95-67 ◽  
1995 ◽  
Author(s):  
A.K.M. Jamaluddin ◽  
M. Vandamme ◽  
B.K. Mann
2021 ◽  
Author(s):  
Mingjun Chen ◽  
Peisong Li ◽  
Yili Kang ◽  
Xinping Gao ◽  
Dongsheng Yang ◽  
...  

Abstract The low flowback efficiency of fracturing fluid would severely increase water saturation in a near-fracture formation and limit gas transport capacity in the matrix of a shale gas reservoir. Formation heat treatment (FHT) is a state-of-the-art technology to prevent water blocking induced by fracturing fluid retention and accelerate gas desorption and diffusion in the matrix. A comprehensive understanding of its formation damage removal mechanisms and determination of production improvement is conducive to enhancing shale gas recovery. In this research, the FHT simulation experiment was launched to investigate the effect of FHT on gas transport capacity, the multi-field coupling model was established to determine the effective depth of FHT, and the numerical simulation model of the shale reservoir was established to analyze the feasibility of FHT. Experimental results show that the shale permeability and porosity were rising overall during the FHT, the L-1 permeability increased by 30- 40 times, the L-2 permeability increased by more than 100 times. The Langmuir pressure increased by 1.68 times and the Langmuir volume decreased by 26%, which means the methane desorption efficiency increased. Results of the simulation demonstrate that the FHT process can practically improve the effect of hydraulic fracturing and significantly increase the well production capacity. The stimulation mechanisms of the FHT include thermal stress cracking, organic matter structure changing, and aqueous phase removal. Furthermore, the special characteristics of the supercritical water such as the strong oxidation, can not be ignored, due to the FHT can assist the retained hydraulic fracturing fluid to reach the critical temperature and pressure of water and transform to the supercritical state. The FHT can not only alleviate the formation damage induced by the fracturing fluid, but also make good use of the retained fracturing fluid to enhance the permeability of a shale gas reservoir, which is an innovative method to dramatically enhance gas transport capacity in shale matrix.


1996 ◽  
Vol 442 ◽  
Author(s):  
Mitsuhiro Horikawa ◽  
Akihiko Yaoita ◽  
Tsuyoshi Nagata ◽  
Tomohisa Kitano

AbstractEffective methods of gettering metallic impurities were proposed. To achieve effective gettering, an annealing process to induce gettering was modified taking fundamental gettering steps and the difference in the gettering mechanism into account. As the concentration of heavy metal is below solubility in a state-of-the-art clean room, a combination of segregation type gettering and slow cooling heat treatment is an effective technique to remove metal impurities from the device active region. Using this technique, DRAM device characteristics such as leakage current and data retention time can be improved.


2016 ◽  
Vol 35 ◽  
pp. 265-275 ◽  
Author(s):  
Yili Kang ◽  
Mingjun Chen ◽  
Zhangxin Chen ◽  
Lijun You ◽  
Zhiwei Hao

1998 ◽  
Vol 37 (01) ◽  
Author(s):  
A.K.M. Jamaluddin ◽  
L.M. Vandamme ◽  
T.W. Nazarko ◽  
D.B. Bennion

1999 ◽  
Vol 38 (03) ◽  
Author(s):  
A.K.M. Jamaluddin ◽  
M. Hamelin ◽  
K. Harke ◽  
H. McCaskill ◽  
S.A. Mehta

Author(s):  
Anna M. Paradowska ◽  
John W. H. Price ◽  
Raafat Ibrahim

This paper explores the use of state-of-the-art instruments such as neutron and synchrotron diffraction for evaluation of residual stress in carbon steel welded components. The study shows significant variation in transverse residual strain/stress distribution across the length of the weld. Measurements before and after post weld heat treatment are reported together with traditional mechanical tests. The changes in residual stress distribution as weld beads are added in multi-bead welds are also presented. Important practical results are: i) The start and end of the weld are the most critical parts of the weldment. Implementations of run-in and run-out (which are subsequently ground off) can minimize the residual stress at the start and end of the weld. ii) Manipulation of the sequence especially around the weld toes can minimize the value of the residual stress in that region. iii) Post weld heat treatment is very effective at reducing residual stresses.


Sign in / Sign up

Export Citation Format

Share Document