scholarly journals Wear and Corrosion Resistance of Hardened Fe-Al-Mn Grinding Ball

2020 ◽  
Vol 14 (1) ◽  
pp. 15-23
Author(s):  
Ratna Kartikasari ◽  
Adi Subardi ◽  
Anita Susiana
Keyword(s):  
Corrosion Resistance ◽  
Chemical Composition ◽  
Austenite Phase ◽  
The Other ◽  
Test Results ◽  
High Alloy ◽  
High Alloy Steel ◽  
Hardening Process ◽  
Wear And Corrosion ◽  
Wear And Corrosion Resistance

Objective: This study aimed to determine the effect of hardening temperature on microstructure, wear and corrosion resistance of Fe-Al-Mn alloy grinding ball. Methods: Hardening process was carried out at 900oC, 950oC, 1000oC, 1050oC and 1100oC, held for 60 minutes and cooled using SAE 20 oil. Tests included chemical composition, SEM-EDS, wear and corrosion resistance test. Results: Chemical composition test results show that this alloy is high alloy steel because it contains 3.6% aluminum (Al), 13.6% manganese (Mn) and 1.1% carbon (C). Microstructures found are austenite, ferrite and kappa. EDS test results show that in the austenite phase, C decreased when hardening temperature increased. Ferrite phase contains Mn which increased when hardening temperature increased while C was the other way around. Mn is relatively stable in the kappa phase. The best wear and corrosion resistance (4.3 x 10-7 mm2/kg and 0.00026 mm/yr) of hardened Fe-Al-Mn grinding ball occurred at 900oC. The corrosion rate is extraordinary. Conclusion: Microstructures of the Fe-Al-Mn alloy grinding ball after the hardening process are austenite, ferrite and kappa.

scholarly journals Influence of Laser Cladding Parameters on Microstructure, Microhardness, Chemical Composition, Wear and Corrosion Resistance of Fe–B Composite Coatings Reinforced with B4C and Si Particles

Coatings ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 809 ◽  
Author(s):  
Dariusz Bartkowski ◽  
Aneta Bartkowska ◽  
Adam Piasecki ◽  
Peter Jurči
Keyword(s):  
Wear Resistance ◽  
Corrosion Resistance ◽  
Chemical Composition ◽  
Laser Beam ◽  
Laser Cladding ◽  
Scanning Speed ◽  
Powder Mixtures ◽  
Wear And Corrosion ◽  
Study Results ◽  
Wear And Corrosion Resistance

The paper presents the study results of a laser cladding process of C45 steel using powder mixtures. The aim of this study was to investigate the microstructure, X-ray diffraction (XRD), chemical composition (EDS), microhardness, corrosion resistance and wear resistance of the newly obtained coatings. Modified coatings were prepared using laser cladding technology. A 1 kW continuous wave Yb:YAG disk laser with a powder feeding system was applied. Two different powder mixtures as well as various laser beam parameters were used. The first powder mixture contained Fe–B, and the second mixture was Fe–B–B4C–Si. Two values of laser beam power (600 and 800 W) and three values of scanning speed (600, 800, and 1000 mm/min) were applied during the studies. As a result of the influence of the laser beam, the zones enriched with modifying elements were obtained. Based on the results of XRD, the presence of phases derived from borides and carbides was found. In all cases analyzed, EDS studies showed that there is an increased content of boron in the dendritic areas, while there is an increased silicon content in interdendritic spaces. The addition of B4C and Si improved properties such as microhardness as well as wear and corrosion resistance. The microhardness of the coating increased from approx. 400 HV to approx. 1100 HV depending on the laser parameters used. The best corrosion resistance was obtained for the Fe–B–B4C–Si coating produced using the highest laser beam scanning speed. An improvement in wear resistance can be seen after wear tests, where the weight loss decreased from about 0.08 g to about 0.05 g.

TANTUNG G

Alloy Digest ◽  
1961 ◽  
Vol 10 (7) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Cutting Tools ◽  
Heat Treating ◽  
Nonferrous Alloy ◽  
Wear And Corrosion ◽  
Wear And Corrosion Resistance

Abstract TANTUNG G is a cast nonferrous alloy containing tantalum or columbium carbide and having wear and corrosion resistance. It is used primarily for cutting tools. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on forming, heat treating, machining, and joining. Filing Code: Co-28. Producer or source: Vascoloy, Ramet Division.

ALLEGHENY LUDLUM TYPE 420

Alloy Digest ◽  
2000 ◽  
Vol 49 (8) ◽  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Heat Treating ◽  
Wear And Corrosion ◽  
Wear And Corrosion Resistance ◽  
Chromium Stainless Steel

Abstract Allegheny Ludlum Type 420 is a hardenable, straight-chromium stainless steel with wear and corrosion resistance. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, and machining. Filing Code: SS-801. Producer or source: Allegheny Ludlum Corporation.

NIROSTA 4031

Alloy Digest ◽  
2005 ◽  
Vol 54 (4) ◽  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Heat Treating ◽  
Wear And Corrosion ◽  
Wear And Corrosion Resistance

Abstract Nirosta 4031 (Type 420) is a martensitic grade of stainless steel that is heat treatable and has wear and corrosion resistance. It is predominately used in the quenched-and-tempered condition. Typical applications are blades and shears for all types of cutting. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as heat treating, machining, and joining. Filing Code: SS-925. Producer or source: ThyssenKrupp Nirosta GmbH.

scholarly journals Preparation and Properties of Mo Coating on H13 Steel by Electro Spark Deposition Process

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3700
Author(s):  
Wenquan Wang ◽  
Ming Du ◽  
Xinge Zhang ◽  
Chengqun Luan ◽  
Yingtao Tian
Keyword(s):  
Corrosion Resistance ◽  
Service Life ◽  
Deposition Time ◽  
Deposition Process ◽  
H13 Steel ◽  
Carbide Phases ◽  
Metallurgical Bonding ◽  
Wear And Corrosion ◽  
Deposition Power ◽  
Wear And Corrosion Resistance

H13 steel is often damaged by wear, erosion, and thermal fatigue. It is one of the essential methods to improve the service life of H13 steel by preparing a coating on it. Due to the advantages of high melting point, good wear, and corrosion resistance of Mo, Mo coating was fabricated on H13 steel by electro spark deposition (ESD) process in this study. The influences of the depositing parameters (deposition power, discharge frequency, and specific deposition time) on the roughness of the coating, thickness, and properties were investigated in detail. The optimized depositing parameters were obtained by comparing roughness, thickness, and crack performance of the coating. The results show that the cross-section of the coating mainly consisted of strengthening zone and transition zone. Metallurgical bonding was formed between the coating and substrate. The Mo coating mainly consisted of Fe9.7Mo0.3, Fe-Cr, FeMo, and Fe2Mo cemented carbide phases, and an amorphous phase. The Mo coating had better microhardness, wear, and corrosion resistance than substrate, which could significantly improve the service life of the H13 steel.

Sign in / Sign up

Export Citation Format

Share Document