scholarly journals Experimental Considerations for the Steady Excavation Performance of a Disc Cutter Bit in an Edge Part of Mortar Specimen.

2001 ◽  
pp. 37-47 ◽  
Author(s):  
Tatsuro MURO ◽  
Kiyoshi TSUCHIYA ◽  
Koichi KOHNO ◽  
Yusuke WAKABAYASHI
Keyword(s):  
Disc Cutter ◽  
Mortar Specimen ◽  
Edge Part ◽  
Excavation Performance

A field parameters-based method for real-time wear estimation of disc cutter on TBM cutterhead

2021 ◽  
Vol 124 ◽  
pp. 103603
Author(s):  
Honggan Yu ◽  
Jianfeng Tao ◽  
Sheng Huang ◽  
Chengjin Qin ◽  
Dengyu Xiao ◽  
...  
Keyword(s):  
Real Time ◽  
Disc Cutter

scholarly journals Study on Cutting Chip in Milling GH4169 with Indexable Disc Cutter

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3135
Author(s):  
Gensheng Li ◽  
Chao Xian ◽  
Hongmin Xin
Keyword(s):  
Chip Thickness ◽  
Cutting Parameters ◽  
Disc Cutter ◽  
Maximum Deviation ◽  
Feed Speed ◽  
Deviation Rate ◽  
Qualitative Relationship ◽  
Predicted Values ◽  
Deformation Coefficient ◽  
And Control

The study and control for chip have a significant impact on machining quality and productivity. In this paper, GH4169 was cut with an indexable disc milling cutter. The chips corresponding to each group of cutting parameters were collected, and the chip parameters (chip curl radius, chip thickness deformation coefficient, and chip width deformation coefficient) were measured. The qualitative relationship between the chip parameters and cutting parameters was studied. The quadratic polynomial models between chip parameters and cutting parameters were established and verified. The results showed that the chip parameters (chip curl radius, chip thickness deformation coefficient and chip width deformation coefficient) were negatively correlated with spindle speed; chip parameters were positively correlated with feed speed; chip parameters were positively correlated with cutting depth. The maximum deviation rate between measured values and predicted values for chip curl radius was 9.37%; the maximum deviation rate for cutting thickness deformation coefficient was 13.8%, and the maximum deviation rate of cutting width deformation coefficient was 7.86%. It can be seen that the established models are accurate. The models have guiding significance for chip control.

Study on Rock-Breaking Simulation and Experiment of Double Disc Cutter of TBM

2016 ◽  
Vol 23 ◽  
pp. 80-88
Author(s):  
F. Lu ◽  
C. Zhang ◽  
J. Sun ◽  
J.X. Tian ◽  
M. Liu ◽  
...  
Keyword(s):  
Rock Breaking ◽  
Disc Cutter ◽  
Element Analysis ◽  
Breaking Effect ◽  
The Finite Element Analysis ◽  
Breaking Mechanism ◽  
Simulation And Experiment ◽  
Tbm Cutter ◽  
Cutter Spacing ◽  
The Impact

In order to improve working efficiency of the tunneling process and extend working life of disc cutter, explore the impact of cutter spacing and loading for the cutter rock-breaking effect. With the theory of rock crushing, Based on the finite element analysis software ABAQUS, the process of disc cutter breaking rock is simulated, considering the adjacent cutters sequential constraints, then, to make sure two cutter space with the method of SE in experiment.The simulation results showed that the optimal cutter spacings were both about 80mm in the same loading and the sequentially loading, but the rock-breaking effect of sequentially loading is better than the same loading. The experimental data showed that the minimum specific energy of rock breaking is appeared cutter spacing between 80mm and 90mm. Thus, the correctness and rationality of the simulation was verified. The study is good for understanding the rock-breaking mechanism of double disc cutter and has a certain promoting value to optimize TBM cutter system.Keywords:TBM, rock fragmentation, ABAQUS, cutter spacing, sequentially cutting

Sign in / Sign up

Export Citation Format

Share Document