Infrared Thermography for Investigation of Surface Quality in Dry Finish Turning of Ti6Al4V

The machining of titanium alloys always raises issues because of their peculiar chemical and physical characteristics as compared to traditional steel or aluminum alloys. A proper selection of parameters and their monitoring during the cutting operation makes it possible to minimize the surface roughness and cutting force. In this experimental study, infrared thermography was used as a control parameter of the surface roughness of Ti6A4V in dry finish turning. An analysis of variance was carried out to determine the effect of the main cutting parameters (cutting speed and feed rate) on the surface roughness and cutting temperature. In the examined range of the machining parameters, cutting speed and feed were found to have a primary effect on the surface roughness of the machined parts. Cutting speed also significantly affected the temperature of the cutting region, while feed was of second order. Higher cutting speeds and intermediate feed values gave the best surface roughness. A regression analysis defined some models to relate the cutting temperature and surface roughness to the machining parameters. Infrared thermography demonstrated that the cutting temperature could be related to roughness.

Effect of cutting parameters on tool life during end milling of AISI 4340 under MQL condition

Purpose The purpose of this paper is to study the cutting performance of high-speed regime end milling of AISI 4340 by investigating the tool life and wear mechanism of steel using the minimum quantity lubrication (MQL) technique to deliver the cutting fluid. Design/methodology/approach The experiments were designed using Taguchi L9 orthogonal array with the parameters chosen: cutting speed (between 300 and 400 m/min), feed rate (between 0.15 and 0.3 mm/tooth), axial depth of cut (between 0.5 and 0.7 mm) and radial depth of cut (between 0.3 and 0.7 mm). Toolmaker microscope, optical microscope and Hitachi SU3500 Variable Pressure Scanning Electron Microscope used to measure tool wear progression and wear mechanism. Findings Cutting speed 65.36%, radial depth of cut 24.06% and feed rate 6.28% are the cutting parameters that contribute the most to the rate of tool life. The study of the tool wear mechanism revealed that the oxide layer was observed during lower and high cutting speeds. The former provides a cushion of the protective layer while later reduce the surface hardness of the coated tool Originality/value A high-speed regime is usually carried out in dry conditions which can shorten the tool life and accelerate the tool wear. Thus, this research is important as it investigates how the use of MQL and cutting parameters can prolong the usage of tool life and at the same time to achieve a sustainable manufacturing process.

Method for an Effective Selection of Tools and Cutting Conditions during Precise Turning of Non-Alloy Quality Steel C45

The paper presents a constructing methodology for a modern approach to tools selection and solving the problem of assigning optimal cutting parameters for specific production conditions. The mathematical formulation determining the extreme values of the technological process optimality criteria is obtained. A system of technical and economic quality indicators for cutting tools is proposed. This system allows principles’ implementation of decentralization and interoperability “Industry 4.0” via finite element modeling of the cutting process based on solving the problem of orthogonal free cutting modeling. The proposed methodology further usage is possible by creating a standardized database on the parameters of the tool: the adhesive component of the friction cutting coefficient for processing of a specific pair of cutting and tool materials (or tool coating material) and the impacts of the cutting-edge radius on cutting efficiency of a particular material.

Improving machining stability of AISI-4140 with magnetic field

Several methods have been developed in order to improve the traditional machining processes and machining outputs. In this study, the effect of the magnetic field on the turning process was investigated. AISI-4140 was machined with different cutting speeds and magnetic flux density magnitudes. The magnetic field was generated with neodymium magnets. Machining stability, surface roughness, and maximum cutting temperature were measured. Additionally, chip shapes were examined. The machining stability was determined by measuring the vibration amplitude and other vibrational parameters (natural frequency, stiffness, and damping coefficients). Conventional turning and magnetic assisted turning were performed under the same cutting parameters consecutively, and the results were compared. According to the results, it was observed that neodymium magnets attached to the cutting tool improve machining stability and damping properties. Surface roughness was decreased between 6%–10% in magnetic assisted turning. Furthermore, it has been observed that the maximum cutting temperatures have been increased between 10%–45% in the magnetic assisted machining. Besides, it can be said that magnets contribute to improving chip control by collecting the chips on them while machining AISI-4140 steel.

Impact of Cutting Parameters on Cutting Force of AISI 410 and AISI 420 MSS during CNC Dry Milling

A CNC dry milling experiment was conducted for the machining parameter optimization of two grades of Martensitic Stainless steel (MSS). Optimization is done by employing Taguchi method (S/N ratio and ANOVA). The specimens used are MSS grades 410 and 420.The experiments were designed by employing L9 orthogonal array for 3 levels of feed and spindle speeds. The impact of these parameters on cutting force was analyzed. The analysis reveals that spindle speed constitute the maximum impact on cutting force for both MSS grades. Optimum cutting parameters are obtained at 30 mm/min (feed rate) and 1500 rpm (spindle speed). Due to higher Chromium and Carbon content in AISI 420 MSS resulted higher cutting force values compared with AISI 410 MSS. Optimum values of cutting parameters are estimated for improving productivity and quality. The predicted values at optimal conditions are estimated. The results indicate a good conformity with the outcome of experiment.

METHOD FOR CALCULATING CUTTING FORCES BY MODELING CAD WITH A SYSTEM OF GEOMETRIC CUTTING PARAMETERS WITH RADIAL MILLS

The accuracy of processing surfaces of a complex profile largely depends on the selected processing strategy, which will allow creating the same, within certain limits, power characteristics of the shaping process at the intervals of the programmed tool path. In this case, it becomes possible to include tuning modules in programs for CNC machines that form vector values of corrections in certain areas, as reactors for elastic deformations of the cutting process. Therefore, it is especially important to know the modulus and direction of the resulting cutting force vector, which does not necessarily coincide with the feed direction. The purpose of this work is to build a method for calculating cutting forces by modeling the geometric parameters of a cut with a CAD system, a cutter with a nonlinear generatrix. Solid modeling of the process is based on the Boolean operations of "intersection" and "subtraction" of 3D objects: the teeth of a radius cutter with a helical cutting edge and a workpiece "moving" at a feed rate. The tool for the implementation of this method is a software module created on the basis of API functions, the input data for which are: a 3D tool and a workpiece, the equation of the trajectory of its movement and the parameters of the infeed movement. Targeting API properties, the application makes it possible to simulate various trajectories, helical or trochoidal, when machining complex surfaces. In the future, it is possible to take into account the plastic deformation processes in the chip formation zone in the model by connecting external modules. In the course of the conducted research on milling with radial end mills with a helical cutting edge, when two or more teeth are within the arc of contact, it was determined by 3D modeling how much thickness and width the layer cuts off each of the teeth during the feed per revolution. Consequently, in the process of shaping, normal and tangential cutting forces, which are different in direction and modulus, are present as a function of the angle of rotation of the cutter. Therefore, the concept of "circumferential force on the cutter", accepted in the theory of cutting, as a certain constant component of the process, can introduce an error when considering the causes of the excitation mechanism of vibrations of different nature that arise in the processing zone.

Investigation and Mathematical Modelling of Optimized Cutting Parameters for Surface Roughness of EN-8 Alloy Steel

The work done in this work deals with the efficacy of cutting parameters on surface of EN-8 alloy steel. For knowing the optimal effects of cutting parameters response surface methodology was practiced subjected to central composite design matrix. The motive was to introduce an interaction among input parameters, i.e., cutting speed, feed and depth of cut and output parameter, surface roughness. For this, second order response surface model was modeled. The foreseen values obtained were found to be fairly close to observed values, showed that the model could be practiced to forecast the surface roughness on EN-8 within the range of parameter studied. Contours and 3-D plots are generated to forecast the value of surface roughness. It was revealed that surface roughness decreases with increases in cutting speed and it increases with feed. However, there were found negligible or almost no implication of depth of cut on surface roughness whereas feed rate affected the surface roughness most. For lower surface roughness, the optimum values of each one were also evaluated.