Scientific Fundamentals of Industrial Safety in the Multivolume Series «Safety of Russia. Legal, Socio-Economic and Scientific-Technical Aspects»

2020 ◽  
pp. 17-26
Author(s):  
N.A. Makhutov ◽  
◽  
M.M. Gadenin ◽  
S.N. Buinovsky ◽  
A.I. Grazhdankin ◽  
...  
Keyword(s):  
Industrial Safety ◽  
Technical Aspects ◽  
Scientific Technical

Music and neuroimaging: Technical aspects

2003 ◽  
Author(s):  
Julian Paul Keenan ◽  
Jennifer Romanowski ◽  
William Chistiana ◽  
Gottfried Schlaug
Keyword(s):  
Technical Aspects

Discussion on “Industrial safety” at the London Section of the Institution

1939 ◽  
Vol 18 (5) ◽  
pp. 212
Author(s):  
G.W. Clarke ◽  
F. Southwell ◽  
Garrett ◽  
Chambers
Keyword(s):  
Industrial Safety

Clinical Application and Results of the Assessment of Coronary Blood Flow by the Regional Precordial Xenon Residue Detection Technique

1978 ◽  
Vol 17 (04) ◽  
pp. 161-171
Author(s):  
H.-J. Engel ◽  
H. Hundeshagen ◽  
P. R. Lichtlen
Keyword(s):  
Wall Motion ◽  
High Flow ◽  
Detection Technique ◽  
Fatty Tissue ◽  
Technical Aspects ◽  
Residue Detection ◽  
High Affinity ◽  
Artery Disease ◽  
The Right ◽  
Drug Interventions

Methodological and technical aspects as well as application and results of the precordial Xenon-residue-detection technique are critically reviewed. The results concern mainly normal flow in various regions of the heart esp. in the free wall of the right and left ventricle, poststenotic flow in patients with coronary artery disease in relation to the degree of proximal nar-rowings as well as wall motion of the corresponding LV segment, bypassgraft flow and flow after drug interventions esp. nitrates, betablockers, the calcium-antagonist Nifedipine and the coronary dilator Dipyridamole. In spite of its serious limitations (high affinity of Xenon for fatty tissue, geometrical problems in the assessment of flow and its relation to anatomy, gas exchange in situations of high flow etc.), the technique is found to be a usefull investigatory tool. Due to its technical display and the related high costs routine application is, however, prohibitive.

Drying and heating of scrap metal at steelmaking: industrial safety, economics, ecology

2020 ◽  
Vol 76 (12) ◽  
pp. 1353-1258
Author(s):  
V. A. Spirin ◽  
V. E. Nikol’skii ◽  
D. V. Vokhmintsev ◽  
A. A. Moiseev ◽  
P. G. Smirnov ◽  
...  
Keyword(s):  
Energy Efficiency ◽  
High Efficiency ◽  
Steel Production ◽  
Scrap Metal ◽  
Industrial Safety ◽  
Technical Solution ◽  
Metal Charge ◽  
Basic Task ◽  
Scrap Heating ◽  
Winter Time

At steel production based on scrap metal utilization, the scrap heating before charging into a melting facility is an important way of energy efficiency increase and ecological parameters improving. In winter time scrap metal charging with ice inclusions into a metal melt can result in a considerable damage of equipment and even accidents. Therefore, scrap preliminary drying is necessary to provide industrial safety. It was shown, that in countries with warm and low-snow climate with no risk of scrap metal icing up during its transportation and storing in the open air, the basic task being solved at the scrap drying is an increase of energy efficiency of steelmaking. InRussiathe scrap metal drying first of all provides the safety of the process and next - energy saving. Existing technologies of scrap metal drying and heating considered, as well as advantages and drawbacks of technical solutions used at Russian steel plants. In winter time during scrap metal heating at conveyers (Consteel process) hot gases penetrate not effectively into its mass, the heat is not enough for evaporation of wetness in the metal charge. At scrap heating by the furnace gases, a problem of dioxines emissions elimination arises. Application of shaft heaters results in high efficiency of scrap heating. However, under conditions of Russian winter the upper scrap layers are not always heated higher 0 °С and after getting into a furnace bath the upper scrap layers cause periodical vapor explosions. The shaft heaters create optimal conditions for dioxines formation, which emit into atmosphere. It was shown, that accounting Russian economic and nature conditions, the metal charge drying and heating in modified charging buckets by the heat of burnt natural gas or other additional fuel is optimal. The proposed technical solution enables to burnt off organic impurities ecologically safely, to melt down ice, to evaporate the wetness in the scrap as well as to heat the charge as enough as the charging logistics enables it. The method was implemented at several Russian steel plants. Technical and economical indices of scrap metal drying in buckets under conditions of EAF-based shop, containing two furnaces ДСП-100, presented.

Sign in / Sign up

Export Citation Format

Share Document