scholarly journals Exposure assessment of nanotitanium oxide powder handling using real-time size-selective particle number concentration measurements and X-ray fluorescence spectrometry —The possibility of exposure to nonagglomerated nanomaterials during the handling of nanomaterial fine powders—

Author(s):  
Mitsutoshi TAKAYA ◽  
Maromu YAMADA ◽  
Kenichi KOBAYASHI ◽  
Ichiro HIGASHIKUBO ◽  
Masayoshi HAGIWARA ◽  
...  
2013 ◽  
Vol 47 (10) ◽  
pp. 5251-5258 ◽  
Author(s):  
Farhad Salimi ◽  
Mandana Mazaheri ◽  
Sam Clifford ◽  
Leigh R. Crilley ◽  
Rusdin Laiman ◽  
...  

2008 ◽  
Vol 1 (1) ◽  
pp. 435-449
Author(s):  
N. K. Meyer ◽  
A. Lauber ◽  
T. Nussbaumer ◽  
H. Burtscher

Abstract. The efficiency of an electrostatic precipitator (ESP) for reducing wood combustion emissions was investigated. Real-time measurements were conducted by directly reading the change in frequency of the tapered element in a Thermo Scientific 1400a TEOM. The measurements have been shown to be influenced by the charge on the aerosols reaching the tapered element such that the TEOM overestimates mass concentration. This electrostatic effect was cross-checked with particle number concentration measurements where no influence was observed. Placing a radioactive neutraliser prior to the TEOM leads to agreement between observed ESP efficiencies as measured by both the TEOM and a CPC.


2008 ◽  
Vol 8 (3) ◽  
pp. 9641-9672 ◽  
Author(s):  
M. Krudysz ◽  
K. Moore ◽  
M. Geller ◽  
C. Sioutas ◽  
J. Froines

Abstract. Ultrafine particle (UFP) number concentrations vary significantly on small spatial and temporal scales due to their short atmospheric lifetimes and multiplicity of sources. To determine UFP exposure gradients within a community, simultaneous particle number concentration measurements at a network of sites are necessary. Concurrent particle size distribution measurements aid in identifying UFP sources, while providing data to investigate local scale effects of both photochemical and physical processes on UFP. From April to December 2007, we monitored particle size distributions at 13 sites within 350 m to 11 km of each other in the vicinity of the Ports of Los Angeles and Long Beach using Scanning Mobility Particle Sizers (SMPS). Typically, three SMPS units were simultaneously deployed and rotated among sites at 1–2 week intervals. Total particle number concentration measurements were conducted continuously at all sites. Seasonal and diurnal size distribution patterns are complex, highly dependent on local meteorology, nearby PM sources, and times of day, and cannot be generalized over the study area nor inferred from one or two sampling locations. Spatial variation in particle number size distributions was assessed by calculating the coefficient of divergence (COD) and correlation coefficients (r) between site pairs. Results show an overall inverse relationship between particle size and CODs, implying that number concentrations of smaller particles (<40 nm) differ from site to site, whereas larger particles tend to have similar concentrations at various sampling locations. In addition, variations in r values as a function of particle size are not necessarily consistent with corresponding COD values, indicating that using results from correlation analysis alone may not accurately assess spatial variability.


2016 ◽  
Vol 27 (S1) ◽  
pp. 59-71 ◽  
Author(s):  
Angelo Lupi ◽  
Maurizio Busetto ◽  
Silvia Becagli ◽  
Fabio Giardi ◽  
Christian Lanconelli ◽  
...  

Atmosphere ◽  
2020 ◽  
Vol 11 (6) ◽  
pp. 573
Author(s):  
Kristof Starost ◽  
James Njuguna

Graphene oxide (GO) nanoparticles are increasingly being used to tailor industrial composites. However, despite the advantages, GO has shown conceivable health risks and toxicity to humans and the environment if released. This study investigates the influence that GO concentrations have on nanoparticle emissions from epoxy-reinforced carbon fiber hybrid composites (EP/CF) during a lifecycle scenario, that is, a drilling process. The mechanical properties are investigated and an automated drilling methodology in which the background noise is eliminated is used for the nanoparticle emissions measurements. Real-time measurements are collected using a condensation particle counter (CPC), a scanning mobility particle sizer spectrometer (SMPS), a real-time fast mobility particle spectrometer (DMS50) and post-test analytical methods. The results observe that all three nanoparticle reinforced samples demonstrated a statistically significant difference of up to a 243% increase in mean peak particle number concentration in comparison to the EP/CF sample. The results offer a novel set of data comparing the nanoparticle release of GO with varying filler weight concentration and correlating it the mechanical influence of the fillers. The results show that the release characteristics and the influence in particle number concentration are primarily dependent on the matrix brittleness and not necessarily the filler weight concentration within the nanocomposite.


2021 ◽  
Vol 55 (8) ◽  
pp. 4357-4367
Author(s):  
Bin Zhao ◽  
Jerome D. Fast ◽  
Neil M. Donahue ◽  
Manish Shrivastava ◽  
Meredith Schervish ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document