Production Optimisation with Hydraulic Fracturing: Application of Fluid Technology to Control Fracture Height Growth in Deep Hard Rock Formation

Author(s):  
Mohammad Al-Dhamen ◽  
Areiyando Makmun ◽  
Ahmed Hilal
2022 ◽  
Author(s):  
Martin Rylance ◽  
Yaroslav Korovaychuk

Abstract For as long as we have been performing hydraulic fracturing, we have been trying to ensure that we stay out of undesirable horizons, potentially containing water and/or gas. The holy grail of hydraulic fracturing, an absolute control of created fracture height, has eluded the industry for more than 70 years. Of course, there have been many that have claimed solutions, but all the marketed approaches have at best merely created a delay to the inevitable growth and at worst been a snake-oil approach with little actual merit. Fundamentally, the applied techniques have attempted to delay or influence the underlying equations of net-pressure and stress variation; but having to ultimately honour them and by doing so then condemned themselves to limited success or outright failure. Fast forward to 2020, and a reassessment of the relative importance of height-growth constraint and what may have changed to help us achieve this. The development of unconventionals are focused on creating as much surface area as possible in micro/nano-Darcy environments, across almost any phase, but with typically poor line of sight to profit. However, the more valuable business of conventional oil and gas is working in thinner and thinner reservoirs with an often-deteriorating permeability, but with a significantly higher potential economic return. What unconventional has successfully delivered however, is a rapid deployment and acceleration in a range of completion technologies that were unavailable just a few years ago. We will demonstrate that these technologies potentially offer the capability of finally being able to control fracture height-growth. Consideration of a range of previously applied height-growth approaches will demonstrate how they attempted to fool or fudge height growth creation mechanisms. With this clarity, we can consider what advances in completion technology may offer in terms of delivering height growth control. We suggest that with the technology and approaches that are currently available today, that height-growth control is finally within reach. We will go on to describe a multi-well Pilot program, in deployment and execution in 2020/021 in Western Siberia; where billions of barrels remain to be recovered in thin oil-rim, low permeability sandstone reservoirs below gas or above water. A comprehensive assessment of the myriad of height-growth approaches that have been utilized over the last 70 years was performed, but in each case demonstrated the fallibility and limitations of each of these. However, rather than the interpretation that such control is not achievable, instead we will show a mathematically sound approach, along with field data and evidence that this is possible. The presentation will demonstrate that completion advances over the last 10 - 15 years make this approach a reality in the present day; and that broader field implementation is finally within reach.


2018 ◽  
Author(s):  
Hamzah Kamal ◽  
Prakoso Noke Fajar ◽  
Yudhanto Geraldus ◽  
Soetikno Luciana ◽  
Marbun Ricki Daniel ◽  
...  

2012 ◽  
Vol 27 (01) ◽  
pp. 8-19 ◽  
Author(s):  
M. Kevin Fisher ◽  
Norman R. Warpinski

2021 ◽  
Author(s):  
Abu M. Sani ◽  
Hatim S. AlQasim ◽  
Rayan A. Alidi

Abstract This paper presents the use of real-time microseismic (MS) monitoring to understand hydraulic fracturing of a horizontal well drilled in the minimum stress direction within a high-temperature high-pressure (HTHP) tight sandstone formation. The well achieved a reservoir contact of more than 3,500 ft. Careful planning of the monitoring well and treatment well setup enabled capture of high quality MS events resulting in useful information on the regional maximum horizontal stress and offers an understanding of the fracture geometry with respect to clusters and stage spacing in relation to fracture propagation and growth. The maximum horizontal stress based on MS events was found to be different from the expected value with fracture azimuth off by more than 25 degree among the stages. Transverse fracture propagation was observed with overlapping MS events across stages. Upward fracture height growth was dominant in tighter stages. MS fracture length and height in excess of 500 ft and 100 ft, respectively, were created for most of the stages resulting in stimulated volumes that are high. Bigger fracture jobs yielded longer fracture length and were more confined in height growth. MS events fracture lengths and heights were found to be on average 1.36 and 1.30 times, respectively, to those of pressure-match.


2022 ◽  
Author(s):  
Hashem Al-Obaid ◽  
Sultan A. Asel ◽  
Jon Hansen ◽  
Rio Wijaya

Abstract Many techniques have been used to model, diagnose and detect fracture dimension and propagation during hydraulic fracturing. Diagnosing fracture dimension growth vs time is of paramount importance to reach the desired geometry to maximize hydrocarbon production potential and prevent contacting undesired fluid zones. The study presented here describes a technique implemented to control vertical fracture growth in a tight sandstone formation being stimulated near a water zone. This gas well was completed vertically as openhole with Multi- Stage Fracturing (MSF). Pre-Fracturing diagnostic tests in combination with high-resolution temperature logs provided evidence of vertical fracture height growth downward toward water zone. Pre-fracturing flowback indicated water presence that was confirmed by lab test. Several actions were taken to mitigate fracture vertical growth during the placement of main treatment. An artificial barrier with proppant was placed in the lower zone of the reservoir before main fracturing execution. The rate and viscosity of fracturing fluids were also adjusted to control the net pressure aiming to enhance fracture length into the reservoir. The redesigned proppant fracturing job was placed into the formation as planned. Production results showed the effectiveness of the artificial lower barrier placed to prevent fracture vertical growth down into the water zone. Noise log consists of Sonic Noise Log (SNL) and High Precision Temperature (HPT) was performed. The log analysis indicated that two major fractures were initiated away from water-bearing zone with minimum water production. Additionally, in- situ minimum stress profile indicated no enough contrast between layers to help confine fracture into the targeted reservoir. Commercial gas production was achieved after applying this stimulation technique while keeping water production rate controlled within the desired range. The approach described in this paper to optimize gas production in tight formation with nearby water contact during hydraulic fracturing treatments has been applied with a significant improvement in well production. This will serve as reference for future intervention under same challenging completion conditions.


Sign in / Sign up

Export Citation Format

Share Document