Fracturing Technology - Can We Finally Control Fracture Height?

2022 ◽  
Author(s):  
Martin Rylance ◽  
Yaroslav Korovaychuk

Abstract For as long as we have been performing hydraulic fracturing, we have been trying to ensure that we stay out of undesirable horizons, potentially containing water and/or gas. The holy grail of hydraulic fracturing, an absolute control of created fracture height, has eluded the industry for more than 70 years. Of course, there have been many that have claimed solutions, but all the marketed approaches have at best merely created a delay to the inevitable growth and at worst been a snake-oil approach with little actual merit. Fundamentally, the applied techniques have attempted to delay or influence the underlying equations of net-pressure and stress variation; but having to ultimately honour them and by doing so then condemned themselves to limited success or outright failure. Fast forward to 2020, and a reassessment of the relative importance of height-growth constraint and what may have changed to help us achieve this. The development of unconventionals are focused on creating as much surface area as possible in micro/nano-Darcy environments, across almost any phase, but with typically poor line of sight to profit. However, the more valuable business of conventional oil and gas is working in thinner and thinner reservoirs with an often-deteriorating permeability, but with a significantly higher potential economic return. What unconventional has successfully delivered however, is a rapid deployment and acceleration in a range of completion technologies that were unavailable just a few years ago. We will demonstrate that these technologies potentially offer the capability of finally being able to control fracture height-growth. Consideration of a range of previously applied height-growth approaches will demonstrate how they attempted to fool or fudge height growth creation mechanisms. With this clarity, we can consider what advances in completion technology may offer in terms of delivering height growth control. We suggest that with the technology and approaches that are currently available today, that height-growth control is finally within reach. We will go on to describe a multi-well Pilot program, in deployment and execution in 2020/021 in Western Siberia; where billions of barrels remain to be recovered in thin oil-rim, low permeability sandstone reservoirs below gas or above water. A comprehensive assessment of the myriad of height-growth approaches that have been utilized over the last 70 years was performed, but in each case demonstrated the fallibility and limitations of each of these. However, rather than the interpretation that such control is not achievable, instead we will show a mathematically sound approach, along with field data and evidence that this is possible. The presentation will demonstrate that completion advances over the last 10 - 15 years make this approach a reality in the present day; and that broader field implementation is finally within reach.

2003 ◽  
Author(s):  
M. Bai ◽  
R.H. Morales ◽  
R. Suarez-Rivera ◽  
W.D. Norman ◽  
S. Green

2018 ◽  
Author(s):  
Hamzah Kamal ◽  
Prakoso Noke Fajar ◽  
Yudhanto Geraldus ◽  
Soetikno Luciana ◽  
Marbun Ricki Daniel ◽  
...  

2022 ◽  
Author(s):  
Alexey Yudin ◽  
Mohamed ElSebaee ◽  
Vladimir Stashevskiy ◽  
Omar Almethen ◽  
Ahmed AlJanahi ◽  
...  

Abstract The Ostracod formation in the Awali brownfield is an extremely challenging layer to develop because the tight carbonate rock is interbedded with shaly streaks and because of the presence of a nearby water-bearing zone. Although the Ostracod formation has been in development since 1960, oil recovery has not yet reached 5% because past stimulation attempts experienced rapid production decline. The current project incorporated aggressive fracture design coupled with a unique height growth control (HGC) workflow, improving the development of Ostracod reserves. The HGC technology is a combination of an engineering workflow supported by geomechanical modeling and an advanced simulator of in-situ kinetics and materials transport to model the placement of a customized, impermeable mixture of particles that will restrict fracture growth. The optimized treatment design included injections of the HGC mixture prior to the main fracturing treatment. This injection was done with a nonviscous fluid to improve settling to create an artificial barrier. After the success of a trial campaign in vertical wells, the technique was adjusted for the horizontal wellbores. The high clay content within the Ostracod layers creates a significant challenge for successful stimulation. The high clay content prevents successful acid fracturing and leads to severe embedment with conventional proppant fracturing designs. We introduced a new approach to stimulate this formation with an aggressive tip-screenout design incorporating a large volume of 12/20-mesh proppant to obtain greater fracture width and conductivity, resulting in a significant and sustained oil production gain. The carefully designed HGC technique was efficient in avoiding fracture breakthrough into the nearby water zone, enabling treatments of up to 450,000 lbm to be successfully contained above a 20-ft-thick shaly barrier with small horizontal stress contrast. Independent measurements proved that the fracture height was successfully contained. This trial campaign in vertical wells proved that the combination of aggressive, large fracture designs with the HGC method could help unlock the Ostracod’s potential. Three horizontal wells were drilled and simulated, each with four stages of adjusted HGC technique to verify if this aggressive method was applicable to challenging sand admittance in case of transverse fractures. This rare implementation of HGC mixtures in horizontal wells showed operational success and proof of fracture containment based on pressure signatures and production monitoring. The applied HGC technique was modified with additional injections and improved by advanced modeling that only recently became available. These contributed to a significant increase of treatment volume, making the jobs placed in the Ostracod some of the world’s largest utilizing HGC techniques. The experience gained in this project can be of a paramount value to any project dealing with hydraulic fracturing near a water formation with insufficient or uncertain stress barriers.


2019 ◽  
Vol 3 (1) ◽  
pp. 1-14
Author(s):  
Miriam R. Aczel ◽  
Karen E. Makuch

High-volume hydraulic fracturing combined with horizontal drilling has “revolutionized” the United States’ oil and gas industry by allowing extraction of previously inaccessible oil and gas trapped in shale rock [1]. Although the United States has extracted shale gas in different states for several decades, the United Kingdom is in the early stages of developing its domestic shale gas resources, in the hopes of replicating the United States’ commercial success with the technologies [2, 3]. However, the extraction of shale gas using hydraulic fracturing and horizontal drilling poses potential risks to the environment and natural resources, human health, and communities and local livelihoods. Risks include contamination of water resources, air pollution, and induced seismic activity near shale gas operation sites. This paper examines the regulation of potential induced seismic activity in Oklahoma, USA, and Lancashire, UK, and concludes with recommendations for strengthening these protections.


2020 ◽  
Vol 35 (6) ◽  
pp. 325-339
Author(s):  
Vasily N. Lapin ◽  
Denis V. Esipov

AbstractHydraulic fracturing technology is widely used in the oil and gas industry. A part of the technology consists in injecting a mixture of proppant and fluid into the fracture. Proppant significantly increases the viscosity of the injected mixture and can cause plugging of the fracture. In this paper we propose a numerical model of hydraulic fracture propagation within the framework of the radial geometry taking into account the proppant transport and possible plugging. The finite difference method and the singularity subtraction technique near the fracture tip are used in the numerical model. Based on the simulation results it was found that depending on the parameters of the rock, fluid, and fluid injection rate, the plugging can be caused by two reasons. A parameter was introduced to separate these two cases. If this parameter is large enough, then the plugging occurs due to reaching the maximum possible concentration of proppant far from the fracture tip. If its value is small, then the plugging is caused by the proppant reaching a narrow part of the fracture near its tip. The numerical experiments give an estimate of the radius of the filled with proppant part of the fracture for various injection rates and leakages into the rock.


2012 ◽  
Vol 27 (01) ◽  
pp. 8-19 ◽  
Author(s):  
M. Kevin Fisher ◽  
Norman R. Warpinski

Sign in / Sign up

Export Citation Format

Share Document