Study of the recrystallization of AW-5049 and AW-5754 twin-roll cast alloys by EBSD

2009 ◽  
Vol 100 (6) ◽  
pp. 875-879 ◽  
Author(s):  
Jaromír Uhlíř ◽  
Margarita Slámovᆠ◽  
Petr Homola
Keyword(s):  
Cast Alloys ◽  
Twin Roll Cast ◽  
Twin Roll

The Effect of Thermo-Mechanical Processing on the Properties of some Al-Fe-Si Alloys with High Fe/Si Ratio

2007 ◽  
Vol 555 ◽  
pp. 559-563 ◽  
Author(s):  
Kemal Delijić ◽  
V. Asanović ◽  
Dragan Radonjić
Keyword(s):  
Corrosion Resistance ◽  
Heat Exchangers ◽  
Food Industry ◽  
Plastic Anisotropy ◽  
Processing Parameters ◽  
Mechanical Processing ◽  
Annealing Conditions ◽  
Cast Alloys ◽  
Twin Roll Cast ◽  
Twin Roll

The paper deals with the effects of thermo-mechanical processing parameters on the properties of two Al-Fe-Si foil alloys. Two twin roll cast alloys with high Fe/Si ratios (Fe/Si≈6) were processed under different combinations of homogenization, deformation and annealing treatments. The influence of small additions of manganese on the mechanical behavior and plastic anisotropy of sheets in hardening and annealing conditions are described. The corrosion resistance of tested sheets in chloride ambience is also presented, because this type of Al foils is dominantly used in the packaging (food) industry and heat exchangers.

scholarly journals Analysis of defects in a twin roll cast Mg‐Y‐Zn magnesium alloy

2021 ◽  
Author(s):  
Kristina Kittner ◽  
Madlen Ullmann ◽  
Falko Arndt ◽  
Susanne Berndorf ◽  
Thorsten Henseler ◽  
...  
Keyword(s):  
Magnesium Alloy ◽  
Twin Roll Cast ◽  
Twin Roll

An XPS Study of Native Oxide and Isothermal Oxidation Kinetics at 300 °C of AZ31 Twin Roll Cast Magnesium Alloy

2013 ◽  
Vol 81 (5-6) ◽  
pp. 529-548 ◽  
Author(s):  
H. Saleh ◽  
T. Weling ◽  
J. Seidel ◽  
M. Schmidtchen ◽  
R. Kawalla ◽  
...  
Keyword(s):  
Magnesium Alloy ◽  
Oxidation Kinetics ◽  
Isothermal Oxidation ◽  
Native Oxide ◽  
Cast Magnesium Alloy ◽  
Cast Magnesium ◽  
Xps Study ◽  
Twin Roll Cast ◽  
Twin Roll

Impact of As-Cast Structure on Structure and Properties of Twin-Roll Cast AA8006 Alloy

2000 ◽  
Vol 331-337 ◽  
pp. 161-166 ◽  
Author(s):  
Margarita Slámová ◽  
Z. Juříček ◽  
Vladivoj Očenášek
Keyword(s):  
Structure And Properties ◽  
Cast Structure ◽  
Twin Roll Cast ◽  
Twin Roll

scholarly journals The Influence of Annealing on Microstructure and Microhardness of Twin-roll Cast Al-Mg-Sc-Zr Alloy

2018 ◽  
Vol 134 (1) ◽  
pp. 145-149
Author(s):  
M. Cieslar ◽  
J. Bajer ◽  
M. Šlapáková ◽  
B. Křivská ◽  
M. Zimina ◽  
...  
Keyword(s):  
Twin Roll Cast ◽  
Twin Roll ◽  
Zr Alloy

Effect of Processing Parameters on Microstructure and Properties of Continuously Cast Al-Mg Sheets

2005 ◽  
Vol 482 ◽  
pp. 279-282 ◽  
Author(s):  
Margarita Slámová ◽  
P. Sláma ◽  
Petr Homola ◽  
Miroslav Karlík
Keyword(s):  
High Strength ◽  
Cost Effective ◽  
Processing Parameters ◽  
Direct Chill ◽  
Continuously Cast ◽  
Chill Cast ◽  
Direct Chill Cast ◽  
Twin Roll Cast ◽  
Twin Roll ◽  
Al Mg Alloys

Inner panels of modern ecological cars are nowadays manufactured from Al-Mg alloys. Continuously twin-roll cast sheets are a cost effective substitution for direct-chill cast sheets. The effect of composition and down-stream processing on sheet properties should be well understood in order to produce high quality products, which exhibit good formability and high strength. Finegrained microstructure and well-balanced texture are the necessary pre-requisites. Results of the investigation of twin-roll cast AlMg2Mn0.8 and AlMg3 alloys are reported. Sheets of 1.0 mm gauge were prepared using different processing routes. The route involving homogenisation results in grain coarsening and anisotropy, however, deep-drawing ability is affected only a little.

Sign in / Sign up

Export Citation Format

Share Document