V&M T24

Alloy Digest ◽  
2001 ◽  
Vol 50 (2) ◽  
Keyword(s):  
Fracture Toughness ◽  
Corrosion Resistance ◽  
Power Plant ◽  
Physical Properties ◽  
Tensile Properties ◽  
Heat Treating ◽  
Operating Parameters ◽  
Power Plant Boiler ◽  
Plant Boiler

Abstract Vallourec and Mannesmann Tubes alloy T24 is a development in power-plant boiler-tubing alloys. It was developed to resist increasing operating parameters of pressure and temperature, particularly in ultra-super-critical boilers. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness and creep. It also includes information on corrosion resistance as well as forming and heat treating. Filing Code: SA-508. Producer or source: Vallourec & Mannesmann.

V&M T23

Alloy Digest ◽  
2001 ◽  
Vol 50 (1) ◽  
Keyword(s):  
Fracture Toughness ◽  
Power Plant ◽  
Physical Properties ◽  
Tensile Properties ◽  
Heat Treating ◽  
Operating Parameters ◽  
Power Plant Boiler ◽  
Plant Boiler

Abstract Vallourec and Mannesmann (V and M) Tubes T23 is a power plant boiler tubing alloy developed to resist increasing operating parameters of pressure and temperature. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness and creep. It also includes information on forming, heat treating, and joining. Filing Code: SA-507. Producer or source: Vallourec & Mannesmann.

ALLEGHENY LUDLUM AL276

Alloy Digest ◽  
1996 ◽  
Vol 45 (1) ◽  
Keyword(s):  
Corrosion Resistance ◽  
High Temperature ◽  
Power Plant ◽  
Physical Properties ◽  
Surface Treatment ◽  
Tensile Properties ◽  
Crevice Corrosion ◽  
Heat Treating ◽  
Chemical Plants ◽  
Temperature Performance

Abstract Allegheny Ludlum AL276 is widely used in the most severe environments found in chemical plants and in power plant desulfurization systems. The high molybdenum level with tungsten gives excellent pitting and crevice corrosion resistance. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on low and high temperature performance, and corrosion resistance as well as forming, heat treating, joining, and surface treatment. Filing Code: Ni-497. Producer or source: Allegheny Ludlum Corporation.

INCONEL ALLOY 725

Alloy Digest ◽  
1994 ◽  
Vol 43 (1) ◽  
Keyword(s):  
Fracture Toughness ◽  
Corrosion Resistance ◽  
Shear Strength ◽  
Physical Properties ◽  
Tensile Properties ◽  
High Strength ◽  
Heat Treating ◽  
Inconel Alloy ◽  
Alloy 625

Abstract INCONEL ALLOY 725 is an age-hardenable alloy that displays high strength along with excellent ductility and toughness. Its corrosion resistance is comparable to alloy 625. Good flattening properties are exhibited in age-hardened tubing. This datasheet provides information on composition, physical properties, hardness, tensile properties, and shear strength as well as fracture toughness. It also includes information on corrosion resistance as well as heat treating and machining. Filing Code: Ni-445. Producer or source: Inco Alloys International Inc.

MONEL ALLOY R-405

Alloy Digest ◽  
1963 ◽  
Vol 12 (2) ◽  
Keyword(s):  
Fracture Toughness ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Surface Treatment ◽  
Tensile Properties ◽  
Copper Alloy ◽  
Heat Treating ◽  
Nickel Copper

Abstract MONEL alloy R-405 is a machining grade of nickel-copper alloy that combines toughness, strength and corrosion resistance of MONEL alloy 400 with excellent machinability. The alloy is designed especially for use in automatic screw machines. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness and fatigue. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: Ni-79. Producer or source: Huntington Alloy Products Division.

COPPER ALLOY No. C93500

Alloy Digest ◽  
1982 ◽  
Vol 31 (6) ◽  
Keyword(s):  
Fracture Toughness ◽  
Compressive Strength ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Copper Alloy ◽  
Heat Treating ◽  
Good Resistance ◽  
Corrosion Resistant ◽  
Low Strength

Abstract Copper Alloy No. C93500 is a cast bronze containing nominally 9% lead and 5% tin. It has excellent machinability, low strength and good resistance to corrosion. It is used for corrosion-resistant castings, small bearings and bushings. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and compressive strength as well as fracture toughness. It also includes information on corrosion resistance as well as casting, heat treating, machining, and joining. Filing Code: Cu-439. Producer or source: Copper alloy foundries.

MEEHANITE GF-20

Alloy Digest ◽  
1973 ◽  
Vol 22 (2) ◽  
Keyword(s):  
Fracture Toughness ◽  
Corrosion Resistance ◽  
Shear Strength ◽  
Cast Iron ◽  
Physical Properties ◽  
Surface Treatment ◽  
Tensile Properties ◽  
Gray Cast Iron ◽  
Heat Treating ◽  
Gray Cast

Abstract MEEHANITE GF-20 is a gray cast iron designed principally for high machinability and is used where strength is not an important factor. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength as well as fracture toughness and fatigue. It also includes information on corrosion resistance as well as casting, heat treating, machining, joining, and surface treatment. Filing Code: CI-39. Producer or source: Meehanite Metal Corporation.

BUNTING ALLOY 907

Alloy Digest ◽  
1977 ◽  
Vol 26 (3) ◽  
Keyword(s):  
Fracture Toughness ◽  
Compressive Strength ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Heat Treating ◽  
Tin Bronze ◽  
Standard Alloy

Abstract BUNTING Alloy 907 is a cast copper-tin alloy (tin bronze) recommended for severe service requirements. It is used widely for bearings and gears. It is a standard alloy for the manufacture of cast gear blanks and has long been known as Phosphor Gear Bronze. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and compressive strength as well as fracture toughness. It also includes information on corrosion resistance as well as casting, heat treating, machining, and joining. Filing Code: Cu-328. Producer or source: NL Industries Inc., Bearing Division.

LUMEN ALLOY 9

Alloy Digest ◽  
1957 ◽  
Vol 6 (12) ◽  
Keyword(s):  
Fracture Toughness ◽  
Compressive Strength ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Sea Water ◽  
Heat Treating

Abstract UMEN ALLOY 9 is a manganese bronze having excellent combination of strength and corrosion resistance in fresh and sea water. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and compressive strength as well as fracture toughness and fatigue. It also includes information on corrosion resistance as well as casting, heat treating, machining, and joining. Filing Code: Cu-57. Producer or source: Lumen Bearing Company.

AISI C1060

Alloy Digest ◽  
1969 ◽  
Vol 18 (12) ◽  
Keyword(s):  
Fracture Toughness ◽  
Wear Resistance ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Alloy Steel ◽  
Heat Treating ◽  
Spring Steel ◽  
High Carbon ◽  
Steel Mills

Abstract AISI C1060 is a high-carbon water or oil hardening tool and spring steel recommended for heavy machinery parts, shafts, springs and miscellaneous tools requiring strength and wear resistance. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as heat treating, machining, and joining. Filing Code: CS-32. Producer or source: Carbon and alloy steel mills.

COPPER ALLOY No. 230

Alloy Digest ◽  
1972 ◽  
Vol 21 (3) ◽  
Keyword(s):  
Fracture Toughness ◽  
Corrosion Resistance ◽  
Shear Strength ◽  
High Temperature ◽  
Physical Properties ◽  
Tensile Properties ◽  
Copper Alloy ◽  
Single Phase ◽  
Heat Treating ◽  
Temperature Performance

Abstract COPPER ALLOY No. 230 is a single-phase brass containing 15% zinc which is the most widely used of the low zinc brasses. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength as well as fracture toughness and creep. It also includes information on low and high temperature performance, and corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Cu-252. Producer or source: Brass mills.

Sign in / Sign up

Export Citation Format

Share Document