VANITE

Alloy Digest ◽  
1986 ◽  
Vol 35 (5) ◽  
Keyword(s):  
Wear Resistance ◽  
Tool Steel ◽  
High Speed ◽  
Heat Treating ◽  
High Carbon ◽  
Steel Company ◽  
Cutting Efficiency ◽  
High Speeds ◽  
Aisi Type ◽  
Fine Surface

Abstract VANITE is a high-carbon, high-vanadium modification of the 18W-4Cr-IV (AISI Type T1) high-speed tool steel. Its increased alloy content provides increases in cutting efficiency and wear resistance. Vanite is especially suitable for light cuts at high speeds that produce a fine surface finish. It will hold a keen cutting edge and because of this it is used primarily for broaches, reamers and finishing tools. This datasheet provides information on composition, physical properties, and hardness. It also includes information on heat treating and machining. Filing Code: TS-458. Producer or source: Columbia Tool Steel Company.

SANDVIK APM 2730

Alloy Digest ◽  
2019 ◽  
Vol 68 (4) ◽  
Keyword(s):  
Wear Resistance ◽  
Compressive Strength ◽  
Physical Properties ◽  
Abrasive Wear ◽  
Tool Steel ◽  
High Speed ◽  
Heat Treating ◽  
Abrasive Wear Resistance ◽  
Steel Company ◽  
High Compressive Strength

Abstract Sandvik APM 2730 is a powder metallurgical alloyed hot-isostatic-pressed high-speed tool steel with abrasive wear resistance and high-compressive strength. This datasheet provides information on composition, physical properties, and elasticity. It also includes information on heat treating and machining. Filing Code: TS-763. Producer or source: Sandvik Steel Company.

LESCO T-15 PM

Alloy Digest ◽  
1990 ◽  
Vol 39 (8) ◽  
Keyword(s):  
Powder Metallurgy ◽  
Physical Properties ◽  
Tool Steel ◽  
Abrasion Resistance ◽  
High Speed ◽  
Heat Treating ◽  
High Carbon ◽  
Steel Company ◽  
Good Retention ◽  
Hot Hardness

Abstract LESCOT-15 PM is a special purpose tungsten type high-speed tool steel containing cobalt for good retention of hot hardness and high carbon and vanadium for enhanced abrasion resistance. It is produced by powder metallurgy. This datasheet provides information on composition, physical properties, microstructure, hardness, and elasticity. It also includes information on heat treating and machining. Filing Code: TS-498. Producer or source: Latrobe Steel Company. Originally published August 1989, revised August 1990.

SANDVIK APM 2723

Alloy Digest ◽  
2019 ◽  
Vol 68 (3) ◽  
Keyword(s):  
Wear Resistance ◽  
Compressive Strength ◽  
Physical Properties ◽  
Abrasive Wear ◽  
Tool Steel ◽  
High Speed ◽  
Heat Treating ◽  
Abrasive Wear Resistance ◽  
Steel Company ◽  
High Compressive Strength

Abstract Sandvik APM 2723 is a powder metallurgical alloyed hot-isostatic-pressed high-speed tool steel with abrasive wear resistance and high-compressive strength. This datasheet provides information on composition, physical properties, and elasticity. It also includes information on heat treating. Filing Code: TS-758. Producer or source: Sandvik Steel Company.

CARPENTER FOUR-STAR

Alloy Digest ◽  
1972 ◽  
Vol 21 (5) ◽  
Keyword(s):  
Fracture Toughness ◽  
Wear Resistance ◽  
Tool Steel ◽  
High Speed ◽  
High Strength ◽  
Heat Treating ◽  
High Carbon

Abstract CARPENTER FOUR-STAR is a molybdenum-tungsten high-speed tool steel with high carbon and vanadium contents. It has excellent wear resistance along with high strength. This datasheet provides information on composition and hardness as well as fracture toughness. It also includes information on forming, heat treating, machining, and joining. Filing Code: TS-242. Producer or source: Carpenter.

LSS H13 HC

Alloy Digest ◽  
2013 ◽  
Vol 62 (3) ◽  
Keyword(s):  
Wear Resistance ◽  
Physical Properties ◽  
Tool Steel ◽  
Heat Treating ◽  
High Carbon ◽  
Steel Company ◽  
Hot Work Tool Steel ◽  
Carbon Modification ◽  
Specialty Steel

Abstract LSS H13 HC is a hot work tool steel that is a high-carbon modification of LSS H13 (Alloy Digest TS-708, October 2012). This version has improved wear resistance. This datasheet provides information on composition, physical properties, hardness, and elasticity. It also includes information on wear resistance as well as forming, heat treating, and machining. Filing Code: TS-715. Producer or source: Latrobe Specialty Steel Company.

LSS D7

Alloy Digest ◽  
2014 ◽  
Vol 63 (8) ◽  
Keyword(s):  
Fracture Toughness ◽  
Wear Resistance ◽  
Tool Steel ◽  
Heat Treating ◽  
High Carbon ◽  
Steel Company ◽  
High Chromium ◽  
Specialty Steel

Abstract LSS D7 is a high-carbon, high-chromium, air-hardening stainless tool steel with great wear resistance. This datasheet provides information on composition and hardness as well as fracture toughness. It also includes information on wear resistance as well as heat treating and machining. Filing Code: TS-725. Producer or source: Latrobe Specialty Steel Company.

AISI TYPE A6

Alloy Digest ◽  
1973 ◽  
Vol 22 (9) ◽  
Keyword(s):  
Fracture Toughness ◽  
Wear Resistance ◽  
Physical Properties ◽  
Tool Steel ◽  
High Strength ◽  
Heat Treating ◽  
Bend Strength ◽  
High Carbon ◽  
Steel Mills ◽  
Aisi Type

Abstract AISI Type A6 is an air-hardening high-carbon tool steel designed for a combination of high strength, good wear resistance, and good toughness. It is easy to heat treat with a minimum of distortion and is used extensively for plastic molds. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and bend strength as well as fracture toughness and fatigue. It also includes information on forming, heat treating, machining, and joining. Filing Code: TS-262. Producer or source: Tool steel mills.

ALLEGHENY LUDLUM EXOHARD

Alloy Digest ◽  
1971 ◽  
Vol 20 (6) ◽  
Keyword(s):  
Fracture Toughness ◽  
Wear Resistance ◽  
Physical Properties ◽  
Tool Steel ◽  
High Speed ◽  
Heat Treating ◽  
Aisi Type ◽  
Steel Aisi

Abstract ALLEGHENY LUDLUM EXOHARD is an ultrahard high-speed tool steel (AISI Type M47) suited for machining hard and otherwise difficult-to-machine materials. This datasheet provides information on composition, physical properties, and hardness as well as fracture toughness. It also includes information on wear resistance as well as heat treating, machining, and joining. Filing Code: TS-234. Producer or source: Allegheny Ludlum Corporation.

AISI TYPE A10

Alloy Digest ◽  
1969 ◽  
Vol 18 (6) ◽  
Keyword(s):  
Fracture Toughness ◽  
Wear Resistance ◽  
Tool Steel ◽  
Roller Bearing ◽  
High Hardness ◽  
Heat Treating ◽  
High Carbon ◽  
Aisi Type ◽  
Drawing Dies

Abstract AISI Type A10 is a high-carbon graphitic tool steel capable of developing high hardness and wear resistance. It is recommended for shear blades, blanking and forming dies, drawing dies and wear plates. This datasheet provides information on composition and hardness as well as fracture toughness. It also includes information on forming, heat treating, machining, and joining. Filing Code: TS-220. Producer or source: Timken Roller Bearing Company.

CHROMEWEAR 300

Alloy Digest ◽  
1981 ◽  
Vol 30 (12) ◽  
Keyword(s):  
Wear Resistance ◽  
Surface Treatment ◽  
Tool Steel ◽  
Abrasion Resistance ◽  
Heat Treating ◽  
High Carbon ◽  
Wear Resistant ◽  
High Chromium ◽  
Chromium Steels ◽  
Aisi Type

Abstract CHROMEWEAR 300 is an air-hardening tool steel developed for applications that require extremely high abrasion resistance. It far exceeds the wear-resistance properties of the air-hardening high-carbon high-chromium steels, and is even superior in wear resistance to the high wear-resistant AISI Type A7 (CHROMEWEAR) tool steel. Its many applications include brick-mold liners, granulator knives, liners for sand slingers and extrusion punches for ceramics. This datasheet provides information on composition and hardness. It also includes information on wear resistance as well as forming, heat treating, machining, and surface treatment. Filing Code: TS-392. Producer or source: Teledyne Vasco.

Sign in / Sign up

Export Citation Format

Share Document