scholarly journals Nonlinear Analysis of Tie Confined Columns

2020 ◽  
Vol 3 (1) ◽  
pp. 130-138
Author(s):  
Ranajay Bhowmick
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Distribution Patterns ◽  
Complex Stress ◽  
Element Analysis ◽  
Suitable Material ◽  
Dimensional Finite Element ◽  
Static And Dynamic Loads ◽  
Three Dimensional Finite Element ◽  
Concentric Loading

Columns, being a very important component of the building structure, are required to be strong enough and also sufficiently deformable to withstand all possible static and dynamic loads to maintain the integrity of the structure throughout their entire life. The strength and the deformability of the columns can be increased by confining the concrete with lateral reinforcements provided in the form of the spirals, hoops or ties. Several experimental and analytical studies have been carried out by various researchers over the years to determine the extent of improvement that can be made to the strength and ductility of the columns, subjected to concentric loading, by confining them using lateral reinforcements. In the present study three-dimensional finite element models of confined concrete columns have been made using ANSYS and analyzed under the application of static concentric loading to find out the effects of lateral confinement. Suitable material models for both concrete and steel have been chosen and nonlinear finite element analysis (FEA) of laterally confined three-dimensional concrete column models have been carried out. The numerical methodology, at first, has been verified against previous experimental results. Then different types of lateral confinements have been modeled and the stress-strain responses and the complex stress distribution patterns have been studied and compared to find out the better type of confinement.

All-on-4 Concept: A 3-Dimensional Finite Element Analysis

2015 ◽  
Vol 41 (2) ◽  
pp. 163-171 ◽  
Author(s):  
Gianpaolo Sannino
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Distribution Patterns ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Biomechanical Behavior ◽  
Dimensional Finite Element ◽  
Von Mises ◽  
Three Dimensional Finite Element

The aim of this work was to study the biomechanical behavior of an All-on-4 implant-supported prosthesis through a finite element analysis comparing 3 different tilt degrees of the distal implants. Three-dimensional finite element models of an edentulous maxilla restored with a prosthesis supported by 4 implants were reconstructed to carry out the analysis. Three distinct configurations, corresponding to 3 tilt degrees of the distal implants (15°, 30°, and 45°) were subjected to 4 loading simulations. The von Mises stresses generated around the implants were localized and quantified for comparison. Negligible differences in von Mises stress values were found in the comparison of the 15° and 30° models. From a stress-level viewpoint, the 45° model was revealed to be the most critical for peri-implant bone. In all the loading simulations, the maximum stress values were always found at the neck of the distal implants. The stress in the distal implants increased in the apical direction as the tilt degree increased. The stress location and distribution patterns were very similar among the evaluated models. The increase in the tilt degree of the distal implants was proportional to the increase in stress concentration. The 45° model induced higher stress values at the bone-implant interface, especially in the distal aspect, than the other 2 models analyzed.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

scholarly journals Three-Dimensional Finite Element Analysis of Stress Distribution in a Tooth Restored with Full Coverage Machined Polymer Crown

2021 ◽  
Vol 11 (3) ◽  
pp. 1220
Author(s):  
Azeem Ul Yaqin Syed ◽  
Dinesh Rokaya ◽  
Shirin Shahrbaf ◽  
Nicolas Martin
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
Intraoral Scanner ◽  
Element Analysis ◽  
Dental Ceramic ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Ceramic Crown

The effect of a restored machined hybrid dental ceramic crown–tooth complex is not well understood. This study was conducted to determine the effect of the stress state of the machined hybrid dental ceramic crown using three-dimensional finite element analysis. Human premolars were prepared to receive full coverage crowns and restored with machined hybrid dental ceramic crowns using the resin cement. Then, the teeth were digitized using micro-computed tomography and the teeth were scanned with an optical intraoral scanner using an intraoral scanner. Three-dimensional digital models were generated using an interactive image processing software for the restored tooth complex. The generated models were imported into a finite element analysis software with all degrees of freedom concentrated on the outer surface of the root of the crown–tooth complex. To simulate average occlusal load subjected on a premolar a total load of 300 N was applied, 150 N at a buccal incline of the palatal cusp, and palatal incline of the buccal cusp. The von Mises stresses were calculated for the crown–tooth complex under simulated load application was determined. Three-dimensional finite element analysis showed that the stress distribution was more in the dentine and least in the cement. For the cement layer, the stresses were more concentrated on the buccal cusp tip. In dentine, stress was more on the cusp tips and coronal 1/3 of the root surface. The conventional crown preparation is a suitable option for machined polymer crowns with less stress distribution within the crown–tooth complex and can be a good aesthetic replacement in the posterior region. Enamic crowns are a good viable option in the posterior region.

Sign in / Sign up

Export Citation Format

Share Document