scholarly journals Reflective Fiber Surface Plasmon Resonance Sensor for High-Sensitive Mercury Ion Detection

2019 ◽  
Vol 9 (7) ◽  
pp. 1480 ◽  
Author(s):  
Zhenlin Chen ◽  
Kunlin Han ◽  
Ya-Nan Zhang
Keyword(s):  
Surface Plasmon Resonance ◽  
Surface Plasmon ◽  
Plasmon Resonance ◽  
Gold Film ◽  
Mercury Ion ◽  
Great Promise ◽  
Water Safety ◽  
Ion Sensor ◽  
Sensitive Film ◽  
Resonance Sensor

This paper proposes a reflective fiber mercury ion sensor based on the surface plasmon resonance (SPR) principle and chitosan (CS)/polyacrylic acid (PAA) multilayer sensitive film. By optimizing the coating parameters of the gold film, the refractive index (RI) sensitivity of the reflective SPR sensor is demonstrated to be 2110.33 nm/RIU. Then, a multi-layer CS/PAA film is fixed on the surface of the gold film as a mercury ion sensitive film to form a reflective SPR fiber mercury ion sensor. Experimental results demonstrate that the sensor can be used to detect different concentrations of mercury ions with a high sensitivity of 0.5586 nm/μM and good specificity and repeatability. Therefore, the reflective SPR fiber mercury ion sensor shows great promise for future applications of environmental monitoring and drinking water safety.

Preparation and Characterization of Nanoporous Gold Film Based Surface Plasmon Resonance Sensor

2018 ◽  
Vol 38 (2) ◽  
pp. 0228002
Author(s):  
王丽 Wang Li ◽  
万秀美 Wan Xiumei ◽  
高然 Gao Ran ◽  
逯丹凤 Lu Danfeng ◽  
祁志美 Qi Zhimei
Keyword(s):  
Surface Plasmon Resonance ◽  
Surface Plasmon ◽  
Plasmon Resonance ◽  
Gold Film ◽  
Nanoporous Gold ◽  
Surface Plasmon Resonance Sensor ◽  
Resonance Sensor

scholarly journals Microstructured Surface Plasmon Resonance Sensor Based on Inkjet 3D Printing Using Photocurable Resins with Tailored Refractive Index

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2518
Author(s):  
Nunzio Cennamo ◽  
Lorena Saitta ◽  
Claudio Tosto ◽  
Francesco Arcadio ◽  
Luigi Zeni ◽  
...  
Keyword(s):  
Surface Plasmon Resonance ◽  
3D Printing ◽  
Surface Plasmon ◽  
Plasmon Resonance ◽  
Optical Sensor ◽  
Low Cost ◽  
3D Print ◽  
Spr Sensor ◽  
Resonance Sensor ◽  
3D Printed

In this work, a novel approach to realize a plasmonic sensor is presented. The proposed optical sensor device is designed, manufactured, and experimentally tested. Two photo-curable resins are used to 3D print a surface plasmon resonance (SPR) sensor. Both numerical and experimental analyses are presented in the paper. The numerical and experimental results confirm that the 3D printed SPR sensor presents performances, in term of figure of merit (FOM), very similar to other SPR sensors made using plastic optical fibers (POFs). For the 3D printed sensor, the measured FOM is 13.6 versus 13.4 for the SPR-POF configuration. The cost analysis shows that the 3D printed SPR sensor can be manufactured at low cost (∼15 €) that is competitive with traditional sensors. The approach presented here allows to realize an innovative SPR sensor showing low-cost, 3D-printing manufacturing free design and the feasibility to be integrated with other optical devices on the same plastic planar support, thus opening undisclosed future for the optical sensor systems.

scholarly journals Design and validation of fiber optic localized surface plasmon resonance sensor for thyroglobulin immunoassay with high sensitivity and rapid detection

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Hyeong-Min Kim ◽  
Dae Hong Jeong ◽  
Ho-Young Lee ◽  
Jae-Hyoung Park ◽  
Seung-Ki Lee
Keyword(s):  
Surface Plasmon Resonance ◽  
Optical Fiber ◽  
Surface Plasmon ◽  
Plasmon Resonance ◽  
Localized Surface Plasmon Resonance ◽  
Optical Fiber Sensor ◽  
Fiber Sensor ◽  
Localized Surface Plasmon ◽  
Simple Method ◽  
Resonance Sensor

AbstractA simple optical fiber sensor based on localized surface plasmon resonance was constructed for direct and rapid measurement of thyroglobulin (Tg). Specific tests for Tg in patients that have undergone thyroidectomy are limited because of insufficient sensitivity, complicated procedures, and in some cases, a long time to yield a result. A sensitive, fast, and simple method is necessary to relieve the psychological and physical burden of the patient. Various concentrations of Tg were measured in a microfluidic channel using an optical fiber sensor with gold nanoparticles. The sensor chip has a detection limit of 93.11 fg/mL with no specificity for other antigens. The potential applicability of the Tg sensing system was evaluated using arbitrary samples containing specific concentrations of Tg. Finally, the sensor can be employed to detect Tg in the patient’s serum, with a good correlation when compared with the commercial kit.

scholarly journals An Enhanced Plastic Optical Fiber-Based Surface Plasmon Resonance Sensor with a Double-Sided Polished Structure

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1516
Author(s):  
Lian Liu ◽  
Shijie Deng ◽  
Jie Zheng ◽  
Libo Yuan ◽  
Hongchang Deng ◽  
...  
Keyword(s):  
Surface Plasmon Resonance ◽  
Optical Fiber ◽  
Surface Plasmon ◽  
Plasmon Resonance ◽  
Low Cost ◽  
Fiber Axis ◽  
Plastic Optical Fiber ◽  
Au Film ◽  
Spr Sensor ◽  
Resonance Sensor

An enhanced plastic optical fiber (POF)-based surface plasmon resonance (SPR) sensor is proposed by employing a double-sided polished structure. The sensor is fabricated by polishing two sides of the POF symmetrically along with the fiber axis, and a layer of Au film is deposited on each side of the polished region. The SPR can be excited on both polished surfaces with Au film coating, and the number of light reflections will be increased by using this structure. The simulation and experimental results show that the proposed sensor has an enhanced SPR effect. The visibility and full width at half maximum (FWHM) of spectrum can be improved for the high measured refractive index (RI). A sensitivity of 4284.8 nm/RIU is obtained for the double-sided POF-based SPR sensor when the measured liquid RI is 1.42. The proposed SPR sensor is easy fabrication and low cost, which can provide a larger measurement range and action area to the measured samples, and it has potential application prospects in the oil industry and biochemical sensing fields.

Dual-mode surface plasmon resonance sensor chip using a grating 3D-printed prism

2021 ◽  
Vol 1147 ◽  
pp. 23-29
Author(s):  
Chutiparn Lertvachirapaiboon ◽  
Akira Baba ◽  
Kazunari Shinbo ◽  
Keizo Kato
Keyword(s):  
Surface Plasmon Resonance ◽  
Surface Plasmon ◽  
Plasmon Resonance ◽  
Sensor Chip ◽  
Surface Plasmon Resonance Sensor ◽  
Dual Mode ◽  
Resonance Sensor ◽  
3D Printed
Sign in / Sign up

Export Citation Format

Share Document