scholarly journals Solar-Driven Chemical Looping Methane Reforming Using ZnO Oxygen Carrier for Syngas and Zn Production in a Cavity-Type Solar Reactor

Catalysts ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1356
Author(s):  
Srirat Chuayboon ◽  
Stéphane Abanades

Converting sunlight into chemical fuels and metal commodities, via solar thermochemical conversion processes, is an attractive prospect for the long-term storage of renewable energy. In this study, the combined methane reforming and ZnO reduction in a single reaction for co-production of hydrogen-rich syngas and metallic Zn was demonstrated in a flexible solar thermochemical reactor prototype, driven by highly concentrated sunlight. Using solar energy as the process heat source in chemical-looping methane reforming with the ZnO/Zn oxygen carrier is a means to reduce the dependence on conventional energy resources and to reduce emissions of CO2 and other pollutants, while upgrading the calorific value of the feedstock for the production of energy-intensive and high-value chemical fuels and materials. On-sun experiments were carried out with different operating parameters including operating temperatures (800–1000 °C), inlet methane flow-rates (0.1–0.4 NL/min), and inlet ZnO feeding-rates (0.5–1.0 g/min) both in batch and continuous modes under reduced (0.15 and 0.45 bar) and atmospheric pressures (0.90 bar), thereby demonstrating solar reactor flexibility and reliability. As a result, increasing the temperature promoted net ZnO conversion at the expense of favored methane cracking reaction, which can be lowered by decreasing pressure to vacuum conditions. Diminishing total pressure improved the net ZnO conversion but favored CO2 yield due to insufficient gas residence time. Rising ZnO feeding rate under a constant over-stoichiometric CH4/ZnO molar ratio of 1.5 enhanced ZnO and methane consumption rates, which promoted Zn and syngas yields. However, an excessively high ZnO feeding rate may be detrimental, as ZnO could accumulate when the ZnO feeding rate is higher than the ZnO consumption rate. In comparison, continuous operation demonstrated greater performance regarding higher ZnO conversion (XZnO) and lower methane cracking than batch operation. High-purity metallic Zn with a well-crystallized structure and of micrometric size was produced from both batch and continuous tests under vacuum and atmospheric pressures, demonstrating suitable reactor performance for the solar thermochemical methane-driven ZnO reduction process. The produced Zn metal can be further re-oxidized with H2O or CO2 in an exothermic reaction to produce pure H2 or CO by chemical-looping.

Author(s):  
N R McGlashan

The poor performance of internal combustion (IC) engines can be attributed to the departure from equilibrium in the combustion process. This departure is expressed numerically, as the difference between the working fluid's temperature and an ideal ‘combustion temperature’, calculated using a simple expression. It is shown that for combustion of hydrocarbons to be performed reversibly in a single reaction, impractically high working fluid temperatures are required — typically at least 3500 K. Chemical-looping combustion (CLC) is an alternative to traditional, single-stage combustion that performs the oxidation of fuels using two reactions, in separate vessels: the oxidizer and reducer. An additional species circulates between the oxidizer and reducer carrying oxygen atoms. Careful selection of this oxygen carrier can reduce the equilibrium temperature of the two redox reactions to below current metallurgical limits. Consequently, using CLC it is theoretically possible to approach a reversible IC engine without resorting to impractical temperatures. CLC also lends itself to carbon capture, as at no point is N2 from the air allowed to mix with the CO2 produced in the reduction process and therefore a post-combustion scrubbing plant is not required. Two thermodynamic criteria for selecting the oxygen carrier are established: the equilibrium temperature of both redox reactions should lie below present metallurgical limits. Equally, both reactions must be sufficiently hot to ensure that their reaction velocity is high. The key parameter determining the two reaction temperatures is the change in standard state entropy for each reaction. An analysis is conducted for an irreversible CLC system using two Rankine cycles to produce shaft work, giving an overall efficiency of 86.5 per cent. The analysis allows for irreversibilites in turbine, boiler, and condensers, but assumes reactions take place at equilibrium. However, using Rankine cycles in a CLC system is considered impractical because of the need for high-temperature, indirect heat exchange. An alternative arrangement, avoiding indirect heat exchange, is discussed briefly.


2014 ◽  
Vol 32 (9) ◽  
pp. 842-848 ◽  
Author(s):  
Yan'e ZHENG ◽  
Xing ZHU ◽  
Hua WANG ◽  
Kongzhai LI ◽  
Yuhao WANG ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document