scholarly journals Intensifying the Charging Response of a Phase-Change Material with Twisted Fin Arrays in a Shell-And-Tube Storage System

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1619
Author(s):  
Mohammad Ghalambaz ◽  
Hayder I. Mohammed ◽  
Jasim M. Mahdi ◽  
Amir Hossein Eisapour ◽  
Obai Younis ◽  
...  
Keyword(s):  
Phase Change ◽  
Phase Change Material ◽  
Storage System ◽  
Heating Surface ◽  
Superior Performance ◽  
Three Dimensional Model ◽  
Reference Case ◽  
Storage Rate ◽  
Shell And Tube ◽  
Change Material

A twisted-fin array as an innovative structure for intensifying the charging response of a phase-change material (PCM) within a shell-and-tube storage system is introduced in this work. A three-dimensional model describing the thermal management with charging phase change process in PCM was developed and numerically analyzed by the enthalpy-porosity method using commercial CFD software. Efficacy of the proposed structure of fins for performing better heat communication between the active heating surface and the adjacent layers of PCM was verified via comparing with conventional longitudinal fins within the same design limitations of fin material and volume usage. Optimization of the fin geometric parameters including the pitch, number, thickness, and the height of the twisted fins for superior performance of the proposed fin structure, was also introduced via the Taguchi method. The results show that a faster charging rate, higher storage rate, and better uniformity in temperature distribution could be achieved in the PCMs with Twisted fins. Based on the design of twisted fins, it was found that the energy charging time could be reduced by up to 42%, and the energy storage rate could be enhanced up to 63% compared to the reference case of straight longitudinal fins within the same PCM mass limitations.

Thermal Energy Storage Through Melting of a Commercial Phase Change Material in an Annulus with Radially Divergent Longitudinal Fins

2020 ◽  
Vol 7 (1) ◽  
Author(s):  
Tonny Tabassum Mainul Hasan ◽  
Latifa Begum
Keyword(s):  
Energy Storage ◽  
Phase Change ◽  
Phase Change Material ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Storage System ◽  
Operating Conditions ◽  
Melting Time ◽  
Bottom Part ◽  
Change Material

This study reports on the unsteady two-dimensional numerical investigations of melting of a paraffin wax (phase change material, PCM) which melts over a temperature range of 8.7oC. The PCM is placed inside a circular concentric horizontal-finned annulus for the storage of thermal energy. The inner tube is fitted with three radially diverging longitudinal fins strategically placed near the bottom part of the annulus to accelerate the melting process there. The developed CFD code used in Tabassum et al., 2018 is extended to incorporate the presence of fins. The numerical results show that the average Nusselt number over the inner tube surface, the total melt fraction, the total stored energy all increased at every time instant in the finned annulus compared to the annulus without fins. This is due to the fact that in the finned annulus, the fins at the lower part of the annulus promotes buoyancy-driven convection as opposed to the slow conduction melting that prevails at the bottom part of the plain annulus. Fins with two different heights have been considered. It is found that by extending the height of the fin to 50% of the annular gap about 33.05% more energy could be stored compared to the bare annulus at the melting time of 82.37 min for the identical operating conditions. The effects of fins with different heights on the temperature and streamfunction distributions are found to be different. The present study can provide some useful guidelines for achieving a better thermal energy storage system.

scholarly journals Dynamics of Melting Process in Phase Change Material Windows Determined Based on Direct Light Transmission

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 721
Author(s):  
Dariusz Heim ◽  
Michał Krempski-Smejda ◽  
Pablo Roberto Dellicompagni ◽  
Dominika Knera ◽  
Anna Wieprzkowicz ◽  
...  
Keyword(s):  
Phase Change ◽  
Phase Change Material ◽  
Light Transmission ◽  
Melting Process ◽  
Refraction Index ◽  
Light Transmittance ◽  
Reference Case ◽  
Solar Radiation Intensity ◽  
Direct Light ◽  
Change Material

Detailed analyses of melting processes in phase change material (PCM) glazing units, changes of direct transmittance as well as investigation of refraction index were provided based on laboratory measurements. The main goal of the study was to determine the direct light transmittance versus time under constant solar radiation intensity and stable temperature of the surrounding air. The experiment was conducted on a triple glazed unit with one cavity filled with a paraffin RT21HC as a PCM. The unit was installed in a special holder and exposed to the radiation from an artificial sun. The vertical illuminance was measured by luxmeters and compared with a reference case to determine the direct light transmittance. The transmittance was determined for the whole period of measurements when some specific artefacts were identified and theoretically explained based on values of refractive indexes for paraffins in the solid and liquid state, and for a glass. The melting process of a PCM in a glass unit was identified as a complex one, with interreflections and refraction of light on semi layers characterized by a different physical states (solid, liquid or mushy). These optical phenomena caused nonuniformity in light transmittance, especially when the PCM is in a mushy state. It was revealed that light transmittance versus temperature cannot be treated as a linear function.

Thermal Behavior of Phase Change Material During Charging Inside a Finned Cylindrical Latent Heat Energy Storage System: Effects of the Arrangement and Number of Fins

2010 ◽  
Author(s):  
Dominic Groulx ◽  
Wilson Ogoh
Keyword(s):  
Energy Storage ◽  
Phase Change ◽  
Phase Change Material ◽  
Latent Heat ◽  
Storage System ◽  
Heat Energy ◽  
Hot Water ◽  
Heat Of Fusion ◽  
Melting Front ◽  
Change Material

One way of storing thermal energy is through the use of latent heat energy storage systems. One such system, composed of a cylindrical container filled with paraffin wax, through which a copper pipe carrying hot water is inserted, is presented in this paper. It is shown that the physical processes encountered in the flow of water, the heat transfer by conduction and convection, and the phase change behavior of the phase change material can be modeled numerically using the finite element method. Only charging (melting) is treated in this paper. The appearance and the behavior of the melting front can be simulated by modifying the specific heat of the PCM to account for the increased amount of energy, in the form of latent heat of fusion, needed to melt the PCM over its melting temperature range. The effects of adding fins to the system are also studied, as well as the effects of the water inlet velocity.

Sign in / Sign up

Export Citation Format

Share Document