scholarly journals Device Optimization of a Lead-Free Perovskite/Silicon Tandem Solar Cell with 24.4% Power Conversion Efficiency

Energies ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3383
Author(s):  
Khaoula Amri ◽  
Rabeb Belghouthi ◽  
Michel Aillerie ◽  
Rached Gharbi
Keyword(s):  
Solar Cell ◽  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Doping Concentration ◽  
Power Conversion ◽  
Transport Layer ◽  
Lead Free ◽  
Electron Transport Layer ◽  
Tandem Solar Cell ◽  
Whole Cell

In this work, simulations were performed to optimize the parameters of a lead-free perovskite/silicon tandem solar cell for the improved efficiency and stability of commercial devices. The top sub-cell is based on a lead-free perovskite with a large bandgap of 1.8 eV, an electron transport layer of SnO2/PCBM, which is known for its anti-hysteresis effect, and a hole transport layer of NiO to improve stability, whereas the bottom sub-cell is based on n-type silicon to increase the efficiency of the whole cell. First, the two sub-cells were simulated under standalone conditions for calibration purposes. Then, the current matching condition was obtained by optimizing the thicknesses of the absorber layers of both sub-cells and the doping concentration of the back surface field (BSF) layer of the silicon sub-cell. As a result of this optimization phase, thicknesses of 380 nm and 20 µm for the top and bottom sub-cells, respectively, and a doping concentration of 1022 cm–3 were used in the configuration of the tandem cell, yielding a large open-circuit voltage of 1.76 V and a power conversion efficiency of 24.4% for the whole cell. Finally, the effect of the working temperature was evaluated, and the results reveal that the high performance of lead-free perovskite sub-cells is less affected by an increase in temperature compared to lead-based solar cells, such as those based on CH3NH3PbI3 perovskite.

scholarly journals Digital printing of a novel electrode for stable flexible organic solar cells with a power conversion efficiency of 8.5%

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
S. Wageh ◽  
Mahfoudh Raïssi ◽  
Thomas Berthelot ◽  
Matthieu Laurent ◽  
Didier Rousseau ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Organic Solar Cells ◽  
Power Conversion ◽  
Transport Layer ◽  
Electron Transport Layer ◽  
Solution Processed ◽  
Transparent Conducting

AbstractPoly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) mixed with single-wall nanotubes (SWNTs) (10:1) and doped with (0.1 M) perchloric acid (HClO4) in a solution-processed film, working as an excellent thin transparent conducting film (TCF) in organic solar cells, was investigated. This new electrode structure can be an outstanding substitute for conventional indium tin oxide (ITO) for applications in flexible solar cells due to the potential of attaining high transparency with enhanced conductivity, good flexibility, and good durability via a low-cost process over a large area. In addition, solution-processed vanadium oxide (VOx) doped with a small amount of PEDOT-PSS(PH1000) can be applied as a hole transport layer (HTL) for achieving high efficiency and stability. From these viewpoints, we investigate the benefit of using printed SWNTs-PEDOT-PSS doped with HClO4 as a transparent conducting electrode in a flexible organic solar cell. Additionally, we applied a VOx-PEDOT-PSS thin film as a hole transporting layer and a blend of PTB7 (polythieno[3,4-b] thiophene/benzodithiophene): PC71BM (phenyl-C71-butyric acid methyl ester) as an active layer in devices. Zinc oxide (ZnO) nanoparticles were applied as an electron transport layer and Ag was used as the top electrode. The proposed solar cell structure showed an enhancement in short-circuit current, power conversion efficiency, and stability relative to a conventional cell based on ITO. This result suggests a great carrier injection throughout the interfacial layer, high conductivity and transparency, as well as firm adherence for the new electrode.

scholarly journals Design of Dopant and Lead-Free Novel Perovskite Solar Cell for 16.85% Efficiency

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2110
Author(s):  
Syed Abdul Moiz ◽  
Ahmed N. M. Alahmadi
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Power Conversion ◽  
Perovskite Solar Cell ◽  
Hole Transport ◽  
Transport Layer ◽  
Lead Free ◽  
Hole Transport Layer

Halide based perovskite offers numerous advantages such as high-efficiency, low-cost, and simple fabrication for flexible solar cells. However, long-term stability as well as environmentally green lead-free applications are the real challenges for their commercialization. Generally, the best reported perovskite solar cells are composed of toxic lead (Pb) and unstable polymer as the absorber and electron/hole-transport layer, respectively. Therefore, in this study, we proposed and simulated the photovoltaic responses of lead-free absorber such as cesium titanium (IV) bromide, Cs2TiBr6 with dopant free electron phenyl-C61-butyric acid methyl ester (PCBM), and dopant free hole transport layer N,N′-Di(1-naphthyl)-N,N′-diphenyl-(1,1′-biphenyl)-4,4′-diamine (NPB) for the Ag/BCP/PCBM/Cs2TiBr6/NPB/ITO based perovskite solar cell. After comprehensive optimization of each layer through vigorous simulations with the help of software SCAPS 1D, it is observed that the proposed solar cell can yield maximum power-conversion efficiency up to 16.85%. This efficiency is slightly better than the previously reported power-conversion efficiency of a similar type of perovskite solar cell. We believe that the outcome of this study will not only improve our knowledge, but also triggers further investigation for the dopant and lead-free perovskite solar cell.

scholarly journals Flexible and efficient perovskite quantum dot solar cells via hybrid interfacial architecture

2020 ◽  
Author(s):  
Long Hu ◽  
Qian Zhao ◽  
Shujuan Huang ◽  
Jianghui Zheng ◽  
Xinwei Guan ◽  
...  
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
High Performance ◽  
Mechanical Stability ◽  
Power Conversion ◽  
Transport Layer ◽  
Electron Transport Layer

Abstract All-inorganic CsPbI3 perovskite quantum dots (QDs) have received intense research interest for photovoltaic applications because of the recently demonstrated higher power conversion efficiency compared to solar cells using other QD materials. These QD devices also exhibit good mechanical stability amongst various thin-film photovoltaic technologies. In this work, through developing a hybrid interfacial architecture consisting of CsPbI3 QD/PCBM heterojunctions, we report the formation of an energy cascade for efficient charge transfer at both QD heterointerfaces and QD/electron transport layer interfaces. The champion CsPbI3 QD solar cell has a best power conversion efficiency of 15.1%, which is among the highest report to date. Building on this strategy, we demonstrate the very first perovskite QD flexible solar cell with a record efficiency of 12.3%. A detailed morphological characterization reveals that the perovskite QD film can better retain structure integrity than perovskite bulk thin-film under external mechanical stress. This work is the first to demonstrate higher mechanical endurance of QD film compared to bulk thin-film, and highlights the importance of further research on high‐performance and flexible optoelectronic devices using solution-processed QDs.

scholarly journals Numerical Modeling and Optimization of Lead-Free Hybrid Double Perovskite Solar Cell by Using SCAPS-1D

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Syed Sajjad Hussain ◽  
Saira Riaz ◽  
Ghazi Aman Nowsherwan ◽  
Khizer Jahangir ◽  
Akram Raza ◽  
...  
Keyword(s):  
Solar Cell ◽  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Power Conversion ◽  
Perovskite Solar Cells ◽  
Double Perovskite ◽  
Perovskite Solar Cell ◽  
Lead Free ◽  
Inorganic Perovskite ◽  
Hybrid Perovskite

The highest power conversion efficiency (PCE) for organic-inorganic perovskite solar cells based on lead is reported as 25.2% in 2019. Lead-based hybrid perovskite materials are used in several photovoltaics applications, but these are not highly favored due to the toxicity of lead and volatility of organic cations. On the other hand, hybrid lead-free double perovskite has no such harm. In this research study, SCAPS numerical simulation is utilized to evaluate and compare the results of perovskite solar cell based on double perovskite FA 2 BiCuI 6 and standard perovskite CH 3 NH 3 PbI 3 as an active layer. The results show that the power conversion efficiency obtained in the case of FA 2 BiCuI 6 is 24.98%, while in the case of CH 3 NH 3 PbI 3 , it is reported as 26.42%. This indicates that the hybrid organic-inorganic double perovskite FA 2 BiCuI 6 has the ability to replace hybrid organic-inorganic perovskite CH 3 NH 3 PbI 3 to expand next-generation lead-free harmless materials for solar cell applications.

Sign in / Sign up

Export Citation Format

Share Document