scholarly journals Laboratory-Based Correlation between Liquefaction Resistance and Shear Wave Velocity of Sand with Fines

Geotechnics ◽  
2021 ◽  
Vol 1 (2) ◽  
pp. 219-242
Author(s):  
Anthi I. Papadopoulou ◽  
Theodora M. Tika
Keyword(s):  
Shear Wave ◽  
Laboratory Investigation ◽  
Wave Velocity ◽  
Effective Stress ◽  
Shear Wave Velocity ◽  
Test Results ◽  
Laboratory Studies ◽  
Bender Element ◽  
Liquefaction Resistance ◽  
Overburden Stress

This paper presents the results of a laboratory investigation into the effect of non-plastic fines on the correlation between liquefaction resistance and the shear wave velocity of sand. For this purpose, undrained stress-controlled cyclic triaxial and bender element tests were performed on clean sand and its mixtures with non-plastic silt. It is shown that the correlation between liquefaction resistance and shear wave velocity depends on fines content and confining effective stress. Based on the test results, correlation curves between field liquefaction resistance and overburden stress corrected shear wave velocity for sand containing various contents of fines are derived. These curves are compared to other previously proposed by field and laboratory studies.

scholarly journals Correlation between shear wave velocity and effective confining pressure using cyclic triaxial testing apparatus

2019 ◽  
Vol 92 ◽  
pp. 04009
Author(s):  
Guojun Liu ◽  
Noriyuki Yasufuku ◽  
Ryohei Ishikura ◽  
Qiang Liu
Keyword(s):  
Shear Wave ◽  
Wave Velocity ◽  
Effective Stress ◽  
Shear Wave Velocity ◽  
Confining Pressure ◽  
Similar Rate ◽  
Bender Elements ◽  
Confining Stress ◽  
Liquefaction Resistance ◽  
Ground Shaking

The 2016 Kumamoto earthquakes struck Kumamoto and Ōita regions and caused several devastating liquefaction induced damages. The primary damage was due to the extreme ground shaking of the foreshock and main shock sequence. Therefore, it is essential to develop a quick reliable approach with a high accuracy to assess the ground situation after foreshock or several shocks. Velocity of small shear wave (Vs) was widely used for evaluating the potential liquefaction. This study investigates the possibility of using Vs as a new indicator of the stress state in the soil after earthquake and evaluation of post liquefaction resistance of soil. Cyclic tri-axial apparatus equipped with bender elements were used to conduct two consecutives liquefaction tests on sandy soil. The Vs measured by bender elements was discussed on the relationship with effective stress during the liquefying processes. The results showed that for the sandy soils, a) Vs could not clearly reflect the significant reduction in resistance at re-liquefaction stages by directly comparing the Vs at the end of consolidation between first and stages, b) The shear wave velocity is significantly affected by effective confining pressure c) the shear wave velocity of 190 m/s was at confining pressure of 100 kPa. The shear wave velocity reaches to after 100 m/s after consolidations and re-consolidations. The shear wave velocity was found to reduce to 100 m/s when the effective confining stress reaches to 0 and to around 25 m/s when the double amplitude reaches to 5%; d) the velocity and effective stress decreases with a similar rate in liquefying process.

scholarly journals The Polito Surface Wave flat-file Database (PSWD): statistical properties of test results and some inter-method comparisons

2021 ◽  
Vol 19 (6) ◽  
pp. 2343-2370
Author(s):  
Federico Passeri ◽  
Cesare Comina ◽  
Sebastiano Foti ◽  
Laura Valentina Socco
Keyword(s):  
Surface Wave ◽  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Active Surface ◽  
Statistical Properties ◽  
Test Results ◽  
Flat File ◽  
Research Fields ◽  
Database Content

AbstractThe compilation and maintenance of experimental databases are of crucial importance in all research fields, allowing for researchers to develop and test new methodologies. In this work, we present a flat-file database of experimental dispersion curves and shear wave velocity profiles, mainly from active surface wave testing, but including also data from passive surface wave testing and invasive methods. The Polito Surface Wave flat-file Database (PSWD) is a gathering of experimental measurements collected within the past 25 years at different Italian sites. Discussion on the database content is reported in this paper to evaluate some statistical properties of surface wave test results. Comparisons with other methods for shear wave velocity measurements are also considered. The main novelty of this work is the homogeneity of the PSWD in terms of processing and interpretation methods. A common processing strategy and a new inversion approach were applied to all the data in the PSWD to guarantee consistency. The PSWD can be useful for further correlation studies and is made available as a reference benchmark for the validation and verification of novel interpretation procedures by other researchers.

Soil Liquefaction Evaluation of Offshore Site Based on In Situ Shear Wave Velocity Measurements

2013 ◽  
Vol 405-408 ◽  
pp. 470-473
Author(s):  
Sheng Jie Di ◽  
Ming Yuan Wang ◽  
Zhi Gang Shan ◽  
Hai Bo Jia
Keyword(s):  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Wind Farm ◽  
Soil Liquefaction ◽  
Offshore Wind ◽  
Velocity Measurements ◽  
Liquefaction Resistance ◽  
Liquefaction Potential

A procedure for evaluating liquefaction resistance of soils based on the shear wave velocity measurements is outlined in the paper. The procedure follows the general formal of the Seed-Idriss simplified procedure. In addition, it was developed following suggestions from industry, researchers, and practitioners. The procedure correctly predicts moderate to high liquefaction potential for over 95% of the liquefaction case histories. The case study for the site of offshore wind farm in Jiangsu province is provided to illustrate the application of the proposed procedure. The feature of the soils and the shear wave velocity in-situ tested in site are discussed and the liquefaction potential of the layer is evaluated. The application shows that the layers of the non-cohesive soils in the depths 3-11m may be liquefiable according to the procedure.

scholarly journals Empirical relationships of shear wave velocity, SPT-N value and vertical effective stress for different soils in Mashhad, Iran

2015 ◽  
Vol 58 (3) ◽  
Author(s):  
Azam Ghazi ◽  
Naser Hafezi Moghadas ◽  
Hosein Sadeghi ◽  
Mohamad Ghafoori ◽  
Gholam Reza Lashkaripur
Keyword(s):  
Shear Wave ◽  
Wave Velocity ◽  
Effective Stress ◽  
Shear Wave Velocity ◽  
Response Analysis ◽  
Empirical Relationships ◽  
Data Set ◽  
Fine Grain ◽  
Geophysical Investigations ◽  
Vertical Effective Stress

<p>Shear wave velocity, V<sub>s</sub>, is one of the important input parameters in seismic response analysis of the ground. Various methods have been examined to measure the soil V<sub>s</sub> directly. Direct measurement of V<sub>s</sub> is time consuming and costly, therefore many researchers have been trying to update empirical relationships between V<sub>s</sub> and other geotechnical properties of soils such as SPT Blow count, SPT-N. In this study the existence of a statistical relationship between V<sub>s</sub>, SPT-N<sub>60 </sub>and vertical effective stress, signa<sub>nu</sub>´, is investigated. Data set we used in this study was gathered from geotechnical and geophysical investigations reports. The data have been extracted from more than 130 numbers of geotechnical boreholes from different parts of Mashhad city. In each borehole the V<sub>s</sub> has been measured by downhole method at two meter intervals. The SPT test also has performed at the same depth. Finally relationships were developed by regression analysis for gravels, sands and fine grain soils. The proposed relationships indicate that V<sub>s</sub> is strongly dependent on signa<sub>nu</sub>´. In this paper the effect of fine percent also is considered on the V<sub>s</sub> estimation.</p>

Measurement of small-strain shear modulus Gmax of dry and saturated sands by bender element, resonant column, and torsional shear tests

2008 ◽  
Vol 45 (10) ◽  
pp. 1426-1438 ◽  
Author(s):  
Jun-Ung Youn ◽  
Yun-Wook Choo ◽  
Dong-Soo Kim
Keyword(s):  
Shear Modulus ◽  
Shear Wave ◽  
Shear Wave Velocity ◽  
Small Strain ◽  
Resonant Column ◽  
Test Results ◽  
Bender Element ◽  
Small Strain Shear Modulus ◽  
Torsional Shear ◽  
Saturated Sands

The bender element method is an experimental technique used to determine the small-strain shear modulus (Gmax) of a soil by measuring the velocity of shear wave propagation through a sample. Bender elements have been applied as versatile transducers to measure the Gmax of wet and dry soils in various laboratory apparatuses. However, certain aspects of the bender element method have yet to be clearly specified because of uncertainties in determining travel time. In this paper, the bender element (BE), resonant column (RC), and torsional shear (TS) tests were performed on the same specimens using the modified Stokoe-type RC and TS testing equipment. Two clean sands, Toyoura and silica sands, were tested at various densities and mean effective stresses under dry and saturated conditions. Based on the test results, methods of determining travel time in BE tests were evaluated by comparing the results of RC, TS, and BE tests. Also, methods to evaluate Gmax of saturated sands from the shear-wave velocity (Vs) obtained by RC and BE tests were investigated by comparing the three sets of test results. Biot’s theory on frequency dependence of shear-wave velocity was adopted to consider dispersion of a shear wave in saturated conditions. The results of this study suggest that the total mass density, which is commonly used to convert Gmax from the measured Vs in saturated soils, should not be used to convert Vs to Gmax when the frequency of excitation is 10% greater than the characteristic frequency (fc) of the soil.

scholarly journals Shear modulus of hydrate bearing calcareous sand-fines mixture

2019 ◽  
Vol 92 ◽  
pp. 04002
Author(s):  
Litong Ji ◽  
Abraham C.F. Chiu ◽  
Lu Ma ◽  
Chao Jian
Keyword(s):  
Shear Modulus ◽  
Shear Wave ◽  
Wave Velocity ◽  
Shear Wave Velocity ◽  
Hydrate Formation ◽  
Confining Pressure ◽  
Specimen Preparation ◽  
Bender Element ◽  
Calcareous Sand ◽  
Bender Element Test

This article presents a laboratory study on the maximum shear modulus of a THF hydrate bearing calcareous sand (CS)–fines mixture. The maximum shear modulus was inferred from the shear wave velocity measured from the bender elements installed in a temperature-controlled triaxial apparatus. The specimen preparation procedures were specially designed to mimic the hydrate formation inside the internal pores of CS. A trial test was conducted to validate whether the shear wave velocity is a feasible parameter to monitor the formation and dissociation of hydrate in the CS-fines mixture. Based on the bender element test results, hydrate has a more profound effect than confining pressure on enhancing the maximum shear modulus of CS-fines mixture.

Sign in / Sign up

Export Citation Format

Share Document