scholarly journals Theoretical and Experimental Investigation of the Effect of Pump Laser Frequency Fluctuations on Signal-to-Noise Ratio of Brillouin Dynamic Grating Measurement with Coherent FMCW Reflectometry

Sensors ◽  
2021 ◽  
Vol 21 (8) ◽  
pp. 2870
Author(s):  
Tatsuya Kikuchi ◽  
Ryohei Satoh ◽  
Iori Kurita ◽  
Kazumasa Takada
Keyword(s):  
Light Source ◽  
Signal To Noise Ratio ◽  
Experimental Result ◽  
Theoretical Formula ◽  
Pump Light ◽  
Signal To Noise ◽  
Technical Noise ◽  
Dynamic Grating ◽  
Frequency Fluctuations ◽  
Noise Ratio

Signal-dependent speckle-like noise has constituted a serious factor in Brillouin-grating based frequency-modulated continuous-wave (FMCW) reflectometry and it has been indispensable for improving the signal-to-noise ratio (S/N) of the Brillouin dynamic grating measurement to clarify the noise generation mechanism. In this paper we show theoretically and experimentally that the noise is generated by the frequency fluctuations of the pump light from a laser diode (LD). We could increase the S/N from 36 to 190 merely by driving the LD using a current source with reduced technical noise. On the basis of our experimental result, we derived the theoretical formula for S/N as a function of distance, which contained the second and fourth-order moments of the frequency fluctuations, by assuming that the pump light frequency was modulated by the technical noise. We calculated S/N along the 1.35 m long optical fiber numerically using the measured power spectral density of the frequency fluctuations, and the resulting distributions agreed with the measured values in the 10 to 190 range. Since higher performance levels are required if the pump light source is to maintain the S/N as the fiber length increases, we can use the formula to calculate the light source specifications including the spectral width and rms value of the frequency fluctuations to achieve a high S/N while testing a fiber of a given length.

scholarly journals Performance analysis of dual-media cooperative communication based on wireless and power line under hybrid fading

2019 ◽  
Vol 15 (5) ◽  
pp. 155014771985070
Author(s):  
Zhixiong Chen ◽  
Yifang Jing ◽  
Dongsheng Han ◽  
Lijiao Wang
Keyword(s):  
Cooperative Communication ◽  
Lognormal Distribution ◽  
Signal To Noise Ratio ◽  
Power Line ◽  
Maximal Ratio Combining ◽  
Total Output ◽  
Theoretical Formula ◽  
Signal To Noise ◽  
Generation Function ◽  
Noise Ratio

Wireless communication and power line communication are extensively applied in various fields, such as household Internet of things. For cooperative communication of amplify–forward relay using wireless access and power line transmission, the hybrid model of universal Nakagami wireless fading and lognormal power line fading was used in this study. A comparative analysis of similarities between Gamma and lognormal distributions and lognormal distribution characteristics of relay link signal-to-noise ratio was also carried out. Given the deficiencies of lognormal variable add approximation method, lognormal distribution parameters combined computing method based on moment generation function was proposed. Theoretical formulas of outage probability and bit error rate after amplify–forward relay and maximal-ratio combining was derived on the basis of moment generation function of the total output signal-to-noise ratio of the system. Effectiveness and reliability of the algorithm and theoretical formula were verified through simulation, and influence rules of hybrid channel fading and power distribution on the system performance were analyzed.

scholarly journals An Improved Impact Source Locating System Using FBG Rosette Array

Sensors ◽  
2019 ◽  
Vol 19 (16) ◽  
pp. 3453
Author(s):  
Chen ◽  
Shin
Keyword(s):  
Light Source ◽  
Signal To Noise Ratio ◽  
Fold Increase ◽  
Fiber Axis ◽  
Source Spectrum ◽  
Directional Sensitivity ◽  
Signal To Noise ◽  
Location Accuracy ◽  
System Sensitivity ◽  
Noise Ratio

For structures vulnerable to foreign object impact damages, it would be desirable to detect and locate any occurrence of such impacts. This can be achieved by monitoring the stress waves generated by an impact together with certain source localization algorithms. Being small, electromagnetic influence immune and durable, Fiber Bragg grating (FBG) sensors are advantageous for this task. One drawback of FBGs for this purpose is their uneven directional sensitivity, which limits its localization ability to within 50° on either side of the fiber axis. Beyond this range, the signal is too weak and masked by noises and the location errors increase abruptly. Two approaches have been tested on a 0.8 m × 0.8 m × 6 mm plate for possible improvement on the system accuracy: firstly, an interrogation scheme with stronger light source intensity and steeper edge filter is employed to enhance the signal-to-noise ratio and system sensitivity; secondly, rosettes with two orthogonal FBGs are cascaded together to replace single FBGs to alleviate the directional sensitivity problem. It was found that a four-fold increase in signal to noise ratio contributed by stronger light source does improve the location accuracy, but only marginally. For the rosette approach, the relative positions of the Bragg wavelength of the FBGs and the light source spectrum are crucial to accuracy. Three different wavelength configurations have been tested and the reasons for their success or failure are discussed. It was shown that with an optimal wavelength configuration, the rosette array can virtually extend the good location accuracy to all over the plate.

scholarly journals Signal-to-Noise Ratio of Brillouin Grating Measurement with Micrometer-Resolution Optical Low Coherence Reflectometry

Sensors ◽  
2020 ◽  
Vol 20 (3) ◽  
pp. 936
Author(s):  
Kazumasa Takada ◽  
Shin-ichi Satoh ◽  
Akiya Kawakami
Keyword(s):  
Dynamic Range ◽  
Signal To Noise Ratio ◽  
Pump Light ◽  
Logarithmic Scale ◽  
Signal To Noise ◽  
Light Power ◽  
Low Coherence ◽  
Beat Noise ◽  
Noise Ratio ◽  
Optical Low Coherence Reflectometry

Signal-dependent speckle-like noise was the dominant noise in a Brillouin grating measurement with micrometer-resolution optical low coherence reflectometry (OLCR). The noise was produced by the interaction of a Stokes signal with beat noise caused by a leaked pump light via square-law detection. The resultant signal-to-noise ratio (SNR) was calculated and found to be proportional to the square root of the dynamic range (DR) defined by the ratio of the Stokes signal magnitude to the variance of the beat noise. The calculation showed that even when we achieved a DR of 20 dB on a logarithmic scale, the SNR value was only 7 on a linear scale and the detected signal tended to fluctuate over ±14% with respect to the mean level. We achieved an SNR of 24 by attenuating the pump light power entering the balanced mixer by 55 dB, and this success enabled us to measure the Brillouin spectrum distributions of mated fiber connectors and a 3-dB fused fiber coupler with a micrometer resolution as examples of OLCR diagnosis.

Improved Signal-to-Noise Ratio in Hybrid 2-D Arrays: Experimental Confirmation

1997 ◽  
Vol 19 (2) ◽  
pp. 93-111 ◽  
Author(s):  
Charles D. Emery ◽  
Stephen W. Smith
Keyword(s):  
Signal To Noise Ratio ◽  
Open Circuit ◽  
Array Element ◽  
Coaxial Cable ◽  
Experimental Result ◽  
Signal To Noise ◽  
High Impedance ◽  
Receive Channel ◽  
Noise Ratio ◽  
Pulse Echo

2-D array transducers have shown significant promise for medical ultrasound over conventional linear arrays, at the cost of increasing the number of channels, difficulty of fabrication and array element impedance. The increase in element impedance reduces the power coupled to a 2-D array element from a conventional 50 Ω source in transmit mode. If the array is sparse, which is typical of 2-D arrays, then the net power coupled into the front acoustic load is reduced when compared to a fully sampled aperture. Furthermore, the received signal-to-noise ratio (SNR), when measured through a nonideal amplifier, is degraded because the high impedance 2-D array transducer element cannot efficiently drive the coaxial cable. The reduction in transmit sensitivity and received SNR can be circumvented with the application of multilayer piezoelectric elements. The improvement in transmit occurs because the transducer impedance is better matched to the impedance of the source. In receive, multilayer elements allow more of the open circuit received voltage to fall across the input of the high impedance preamplifier. In this case, the same number of layers are used in transmit and receive. Recently, it has been suggested that separate optimization of the transmit channel and receive channel (a hybrid array) would further improve the pulse-echo SNR. In this paper, we fabricated and tested a hybrid array operating at 1 MHz using a multilayer transmit element and single layer receive element. A 7 Ω transmitter and high impedance preamplifier were placed adjacent to the transmit and receive elements within the transducer assembly. The hybrid pulse-echo SNR improved by 26.4 dB over the conventional array. The experimental result showed good agreement with the KLM model. Furthermore, KLM simulations showed that as the operating frequency of the array increases, the overall improvement over the conventional array increases. For example, a 1.5-D array operating at 2 MHz had an improvement of 30 dB whereas a 7.5 MHz 1.5-D array showed an increase of approximately 38 dB. The separate optimization of the transmit and receive channel for 2-D arrays showed even greater improvement than for 1.5-D arrays. For example, a 2 MHz 2-D array had an improvement of over 44 dB.

Determination of the Best Emulsion for the Microscopy of Crystals

1981 ◽  
Vol 39 ◽  
pp. 32-33
Author(s):  
David A. Grano ◽  
Kenneth H. Downing
Keyword(s):  
Spatial Frequency ◽  
Information Transfer ◽  
Signal To Noise Ratio ◽  
Experimental Situation ◽  
Photographic Emulsion ◽  
Modulation Transfer ◽  
Signal To Noise ◽  
Frequency Space ◽  
Noise Ratio

The retrieval of high-resolution information from images of biological crystals depends, in part, on the use of the correct photographic emulsion. We have been investigating the information transfer properties of twelve emulsions with a view toward 1) characterizing the emulsions by a few, measurable quantities, and 2) identifying the “best” emulsion of those we have studied for use in any given experimental situation. Because our interests lie in the examination of crystalline specimens, we've chosen to evaluate an emulsion's signal-to-noise ratio (SNR) as a function of spatial frequency and use this as our critereon for determining the best emulsion.The signal-to-noise ratio in frequency space depends on several factors. First, the signal depends on the speed of the emulsion and its modulation transfer function (MTF). By procedures outlined in, MTF's have been found for all the emulsions tested and can be fit by an analytic expression 1/(1+(S/S0)2). Figure 1 shows the experimental data and fitted curve for an emulsion with a better than average MTF. A single parameter, the spatial frequency at which the transfer falls to 50% (S0), characterizes this curve.

Experiments in Bright-Field Imaging with Hollow-Cone Illumination

1981 ◽  
Vol 39 ◽  
pp. 226-227
Author(s):  
W. Kunath ◽  
K. Weiss ◽  
E. Zeitler
Keyword(s):  
Signal To Noise Ratio ◽  
Carbon Support ◽  
Electronic System ◽  
Optic Axis ◽  
Hollow Cone ◽  
Signal To Noise ◽  
Bright Field ◽  
Noise Ratio ◽  
Single Field ◽  
Field Imaging

Bright-field images taken with axial illumination show spurious high contrast patterns which obscure details smaller than 15 ° Hollow-cone illumination (HCI), however, reduces this disturbing granulation by statistical superposition and thus improves the signal-to-noise ratio. In this presentation we report on experiments aimed at selecting the proper amount of tilt and defocus for improvement of the signal-to-noise ratio by means of direct observation of the electron images on a TV monitor.Hollow-cone illumination is implemented in our microscope (single field condenser objective, Cs = .5 mm) by an electronic system which rotates the tilted beam about the optic axis. At low rates of revolution (one turn per second or so) a circular motion of the usual granulation in the image of a carbon support film can be observed on the TV monitor. The size of the granular structures and the radius of their orbits depend on both the conical tilt and defocus.

Information capacity and bandwidth limitations in the SEM

1989 ◽  
Vol 47 ◽  
pp. 84-85
Author(s):  
D. C. Joy ◽  
R. D. Bunn
Keyword(s):  
Signal To Noise Ratio ◽  
Critical Dimension ◽  
Information Capacity ◽  
Acquisition Time ◽  
Signal To Noise ◽  
Sem Image ◽  
Probe Size ◽  
Minimum Number ◽  
Noise Ratio ◽  
Signal Channel

The information available from an SEM image is limited both by the inherent signal to noise ratio that characterizes the image and as a result of the transformations that it may undergo as it is passed through the amplifying circuits of the instrument. In applications such as Critical Dimension Metrology it is necessary to be able to quantify these limitations in order to be able to assess the likely precision of any measurement made with the microscope.The information capacity of an SEM signal, defined as the minimum number of bits needed to encode the output signal, depends on the signal to noise ratio of the image - which in turn depends on the probe size and source brightness and acquisition time per pixel - and on the efficiency of the specimen in producing the signal that is being observed. A detailed analysis of the secondary electron case shows that the information capacity C (bits/pixel) of the SEM signal channel could be written as :

Speech Reception in the Presence of Classroom Noise

1979 ◽  
Vol 10 (4) ◽  
pp. 221-230 ◽  
Author(s):  
Veronica Smyth
Keyword(s):  
Signal To Noise Ratio ◽  
Learning Processes ◽  
Speech Discrimination ◽  
Signal To Noise ◽  
Speech Reception ◽  
Monosyllabic Words ◽  
Noise Ratio

Three hundred children from five to 12 years of age were required to discriminate simple, familiar, monosyllabic words under two conditions: 1) quiet, and 2) in the presence of background classroom noise. Of the sample, 45.3% made errors in speech discrimination in the presence of background classroom noise. The effect was most marked in children younger than seven years six months. The results are discussed considering the signal-to-noise ratio and the possible effects of unwanted classroom noise on learning processes.

Sign in / Sign up

Export Citation Format

Share Document