Radiological imaging in treatment planning and monitoring for patients with destructive pulmonary tuberculosis and the use of valvular bronchial blocking

MedAlliance ◽  
2020 ◽  
Vol 8 (4) ◽  
pp. 73-79

In the Russian Federation, most cases of valvular bronchial blocking are associated with the treatment of destructive pulmonary tuberculosis. Bronchial blocking is indicated when there are cavities in various forms of pulmonary tu-berculosis that do not close for long (4 months or more). Bronchial blocking in these cases is meant to close cavi-ties, and bronchopleural fistulas, eliminate bleeding and spontaneous pneumothorax, and treat pleural empyema. Radiological diagnostic techniques are key elements in the planning and control of valvular bronchial blocking. At the planning stage, indications and contraindications for valve placement are assessed, as well as anatomical features that can predict ineffectiveness of the interven-tion, including, as the most important ones, signs of col-lateral ventilation. The most informative method of radio-logical imaging at this stage is computed tomography, which allows a detailed assessment of changes in the lung tissue of the zone of interest, including its surroun-ding, bronchial tree and pleura. When monitoring treat-Рис. 1. Эндобронхиальные клапаны российского производства [14]ment, depending on the clinical situation, it is possible to use both classical X-ray examination and computed tomo graphy. The article presents the tactics of radiologi-cal ima ging methods' application at the stage of selection and control of treatment for patients with destructive pul-monary tuberculosis. Various changes in the target lobe of the lungs after bronchial blocking are shown. Valvular bronchial blocking is an effective addition to the complex treatment of destructive pulmonary tuberculosis, includ-ing its complications, and contributes to the reduction of bacterial shedding. Computed tomography increases the efficiency of valvular bronchial blocking results' forecast, and also is an important monitoring technique after the valve placement

2020 ◽  
Vol 98 (6) ◽  
pp. 47-51
Author(s):  
E. A. Borodulinа ◽  
A. V. Kolsаnov ◽  
P. V. Rogozhkin ◽  
A. A. Mаnukyan

The clinical experience demonstrates the importance of 3D modeling when planning surgical intervention in patients with pulmonary tuberculosis. The 3D model was built up based computed tomography data using Avtoplan software with plug-ins for segmentation of the lung, pathological foci, vascular structures, and bronchial tree. The data obtained during 3D modeling allowed us to plan surgery and the data were fully confirmed during the operation. The 3D model with color mapping reveals syntopy, which is extremely difficult to determine using standard computed tomography and allows the wider use of minimally invasive endoscopic surgical interventions.


1997 ◽  
Vol 18 (10) ◽  
pp. 622-627 ◽  
Author(s):  
David B. Thordarson ◽  
Thomas P. Hedman ◽  
Dominic Gross ◽  
George Magre

Simulated syndesmosis injuries were created in 12 fresh-frozen, below-knee cadaver specimens. Six specimens were repaired with a 4.5 mm stainless steel screw, and six were repaired with a 4.5 mm polylactide screw. Three specimens of each group were tested in load to failure by axially loading with 1400 N and externally rotating to 90°. Three specimens in each group underwent fatigue testing by axially loading with 700 N and applying 2.5 N-m of torque for 57,700 cycles. Radiographs and computed tomography scans were evaluated. None of the screws broke or failed. Similar load to failure was noted in polylactide and control groups. Fatigue testing revealed no significant change in stiffness. No significant screw damage was evident on radiographic or computed tomography evaluation. The data suggest that a polylactide screw has sufficient fatigue and failure strength to allow for healing of this injury in a clinical situation.


2000 ◽  
Vol 42 (5) ◽  
pp. 757
Author(s):  
Myung Hee Chung ◽  
Hae Giu Lee ◽  
Won Jong Yu ◽  
Hong Jun Chung ◽  
Bo Sung Yang ◽  
...  

Author(s):  
D.L. Roke

The growth in horticultural and some industrial development in selected areas of Northland has led to a need for more specific and careful planning and control of limited resources in a number of major catchments. The potential irrigation demands for horhculture comprise over 60% of Northland's potential water requirements. By contrast, farm water supply needs are only 11% of these needs. Because of their importance to the Northland economy, and in the legislation these needs are given a high priority in water resource management planning. Land uses, including pastoral farming, require careful operation to reduce diffuse sources of pollution.


Soviet Review ◽  
1973 ◽  
Vol 14 (2) ◽  
pp. 24-38 ◽  
Author(s):  
N. Fedorenko ◽  
K. Gofman

Sign in / Sign up

Export Citation Format

Share Document