Improving the Performance of Light Trapping in Crystalline Silicon Solar Cell through Effective Surface Texturing

2015 ◽  
Vol 1132 ◽  
pp. 144-159 ◽  
Author(s):  
A.A. Fashina ◽  
K.K. Adama ◽  
M.G. Zebaze Kana ◽  
Winston O. Soboyejo
Keyword(s):  
Solar Cells ◽  
Surface Morphology ◽  
Crystalline Silicon ◽  
Light Trapping ◽  
Surface Texturing ◽  
Visible Spectrum ◽  
Silicon Solar Cells ◽  
Etching Time ◽  
Crystalline Silicon Solar Cell ◽  
Light Rays

We investigate the effect of surface texturing on the light trapping properties of Silicon wafers as a function of reflection reduction and surface morphology. This was achieved by structuring a random square-based pyramids pattern on the surface of Silicon substrate using anisotropy etching. The light trapping effect was optimized for silicon solar cells by investigating the dependence of the silicon surface texturing on the process parameters such as etchant concentration, etching time and temperature. We study the surface morphology by analyzing the surface behaviour of the textured substrate using the atomic force microscope and scanning electron microscope. The results of roughness and optical reflection were obtained using the surface profiler and the UV/VIS the spectrometer respectively. In addition, an analytical modelling method was developed to determine the angles of incidence of light rays with each of the facets of the pyramids and the coordinate of the reflected light rays. The method used here is based on 3-D vector geometry of the pyramidal facets. The optimum parameters are found to be 40min, a temperature of 80oC and with KOH/IPA/DI in the ratio [2:4:46] by volume, yielding a surface roughness over 600 nm and a relative optical reflectance in the visible spectrum less than 10%, using polished Si as reference. The results and analysis of both the modelled and measured reflectance, suggest that the performance of the light trapping technique has a big potential in silicon solar cells application.

scholarly journals Performance of Silicon Solar Cells under the Climatic Conditions of Bangladesh, Part III. Performance of PV Cells under Defuse Light and Applicability for Home Lighting

1970 ◽  
Vol 46 (1) ◽  
pp. 117-122 ◽  
Author(s):  
M Eusuf ◽  
M Khanam ◽  
S Khatun
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Solid Surface ◽  
Tilt Angle ◽  
Crystalline Silicon ◽  
Climatic Conditions ◽  
Solar Panel ◽  
Silicon Solar Cells ◽  
Crystalline Silicon Solar Cell ◽  
Solar Home System

In part II of this series, it was reported that the solar home system (SHS) supplied by REB in some islands of the Meghna river in the district of Narsingdi could not meet the demand of the recipients in the rainy season when the sky remained overcast with cloud. The tilt angle for all installations was 45° facing south. In this study, effects of direct and diffuse sunlight with variation of tilt angles from 0° to 45° were studied using a mono crystalline silicon cell. Pyranometer and the solar panel were kept under identical conditions. Energy absorbed by the solar panel in diffuse sunlight was found 0.55% of that received by the Pyranometer under similar conditions showing that mono crystalline silicon solar cell of the type under study was not suitable for use in SHS. Moreover, the gap between the panel and the solid surface below it has significant effects on the efficiency of the solar cell. Further similar study using different kinds of cells- mono crystalline, poly crystalline and amorphous is needed for proper designs of SHS. Optimization of the gap between the panel and the solid surface below it is important for roof-mounted and ground-mounted panels. Key words: Silicon solar cells; Tilt angle; Diffuse light; Home lighting; Monocrystaline. DOI: http://dx.doi.org/10.3329/bjsir.v46i1.8114 Bangladesh J. Sci. Ind. Res. 46(1), 117-122, 2011   

scholarly journals Hexagonal sphere gratings for enhanced light trapping in crystalline silicon solar cells

2013 ◽  
Vol 22 (S1) ◽  
pp. A111 ◽  
Author(s):  
Johannes Eisenlohr ◽  
Jan Benick ◽  
Marius Peters ◽  
Benedikt Bläsi ◽  
Jan Christoph Goldschmidt ◽  
...  
Keyword(s):  
Solar Cells ◽  
Crystalline Silicon ◽  
Light Trapping ◽  
Silicon Solar Cells ◽  
Crystalline Silicon Solar Cells

Investigation of soldering for crystalline silicon solar cells

2016 ◽  
Vol 28 (4) ◽  
pp. 222-226 ◽  
Author(s):  
Hong Yang ◽  
He Wang ◽  
Dingyue Cao
Keyword(s):  
Solar Cells ◽  
Crystalline Silicon ◽  
Quality Criterion ◽  
Silicon Solar Cells ◽  
Crystalline Silicon Solar Cell ◽  
Solar Module ◽  
Content Type ◽  
Crystalline Silicon Solar Cells ◽  
Soldering Process ◽  
Thermal Expansion Coefficients

Purpose Tabbing and stringing are the critical process for crystalline silicon solar module production. Because of the mismatch of the thermal expansion coefficients between silicon and metal, phenomenon of cell bowing, microcracks formation or cell breakage emerge during the soldering process. The purpose of this paper is to investigate the effect of soldering on crystalline silicon solar cells and module, and reveal soldering law so as to decrease the breakage rates and improve reliability for crystalline silicon solar module. Design/methodology/approach A microscopic model of the soldering process is developed by the study of the crystalline silicon solar cell soldering process in this work. And the defects caused by soldering were analyzed systematically. Findings The defects caused by soldering are analyzed systematically. The optimal soldering conditions are derived for the crystalline silicon solar module. Originality/value The quality criterion of soldering for crystalline silicon solar module is built for the first time. The optimal soldering conditions are derived for the crystalline silicon solar module. This study provides insights into solder interconnection reliability in the photovoltaic (PV) industry.

Effects of Electrochemical Etching Time on the Performance of Porous Silicon Solar Cells on Crystalline n-Type (100) and (111)

2017 ◽  
Vol 46 ◽  
pp. 45-56 ◽  
Author(s):  
Khalid Omar ◽  
Khaldun A. Salman
Keyword(s):  
Solar Cells ◽  
Porous Silicon ◽  
Crystalline Silicon ◽  
Electrochemical Etching ◽  
Silicon Layer ◽  
Porous Silicon Layer ◽  
Silicon Solar Cells ◽  
Etching Time ◽  
Crystalline Silicon Solar Cells ◽  
Coating Layers

Electrochemical etching was carried out to produce porous silicon based on crystalline silicon n-type (100) and (111) wafers. Etching times of 10, 20, and 30 min were applied. Porous silicon layer was used as anti-reflection coating on crystalline silicon solar cells. The optimal etching time is 20 min for preparing porous silicon layers based on crystalline silicon n-type (100) and (111) wafers. Nanopores with high porosity were produced on the porous silicon layer based on crystalline silicon n-type (100) and (111) wafers with average diameters of 5.7 and 5.8 nm, respectively. Average crystallite sizes for the porous silicon layer based on crystalline silicon n-type (100) and (111) wafers were 20.57 and 17.45 nm at 20 and 30 min, respectively, due to the increase in broadening of the full width at half maximum. Photoluminescence peaks for porous silicon layers based on crystalline silicon n-type (100) and (111) wafers increased with growing porosity and a great blue shift in luminescence. The minimum effective coefficient of reflection was obtained from porous silicon layers based on the crystalline silicon n-type (100) wafer compared with n-type (111) wafer and as-grown at different etching times. Porous silicon layers based on the crystalline silicon n-type (100) wafer at 20 min etching time exhibited excellent light trapping at wavelengths ranging from 400 to 1000 nm. Thus, fabricated crystalline silicon solar cells based on porous silicon (100) anti-reflection coating layers achieved the highest efficiency at 15.50% compared to porous silicon (111) anti-reflection coating layers. The efficiency is characterized applying I-V characterization system under 100 mW/cm2 illumination conditions.

Sign in / Sign up

Export Citation Format

Share Document