Medial Placement of a Cementless Acetabular Component in a Modern Alumina-on-Alumina THA

2007 ◽  
Vol 330-332 ◽  
pp. 1243-1246
Author(s):  
Jeong Joon Yoo ◽  
Hee Joong Kim ◽  
Young Min Kim ◽  
Kang Sup Yoon ◽  
Kyung Hoi Koo ◽  
...  
Keyword(s):  
Acetabular Component ◽  
Polyethylene Wear ◽  
Clinical Results ◽  
Harris Hip Score ◽  
Bearing Surface ◽  
The Mean ◽  
Acetabular Components ◽  
Cementless Acetabular Component ◽  
Acetabular Wall

Medial placement of a cementless acetabular component into or beyond the medial wall of a shallow, dysplastic acetabulum is a technique to enhance its coverage during difficult total hip arthroplasty (THA). Dysplastic hips almost always need small size of acetabular component, so an accelerated polyethylene wear can occur when a conventional bearing surface is used. Modern alumina-on-alumina couplings can be an alternative for these patients. We evaluated the clinical results of 43 medially placed cementless acetabular components (PLASMACUP®SC) incorporating a modern alumina bearing surface (BIOLOX® forte). Acetabular components were inserted medially beyond the ilioischial line and, therefore, beyond the level of the cortical bone of the cotyloid notch, and followed up for more than 5 years (range, 60 – 93 months). In 14 hips, the medial acetabular wall was perforated purposefully and the medial aspect of the cup was placed beyond both the ilioischial and the iliopubic line on radiographs. The mean Harris hip score improved from 55.3 points preoperatively to 94.5 points postoperatively. Postoperatively, the hip center migrated 12.1 mm medially and 1.5 mm inferiorly. The average amount of cup protrusion beyond the ilioischial and the iliopubic line was 3.1 mm and 1.9 mm, respectively. The average superolateral coverage of the cup was 98.5 percent. During follow-up, no osteolysis or loosening of acetabular components was observed and no revision was required. Medial placement of a cementless acetabular component into or beyond the medial acetabular wall offers predictable clinical results and durable fixation in modern alumina-on-alumina THA.

Mid-Term Results of Ceramic-on-Ceramic Total Hip Arthroplasty with Sandwich Cup

2006 ◽  
Vol 309-311 ◽  
pp. 1357-1362
Author(s):  
Masahiro Hasegawa ◽  
Akihiro Sudo ◽  
Atsumasa Uchida
Keyword(s):  
Total Hip Arthroplasty ◽  
Hip Arthroplasty ◽  
Hip Dislocation ◽  
Clinical Results ◽  
Total Hip ◽  
The Mean ◽  
Acetabular Components ◽  
Mid Term Results ◽  
Ceramic On Ceramic

In ceramic-on-ceramic total hip arthroplasty (THA), modular acetabular component with a sandwich insertion was developed and evaluated mid-term clinical results. 35 hips had undergone cementless ceramic-on-ceramic THA with sandwich cup (Kyocera, Kyoto, Japan). The mean duration of follow-up was 5 years. 6 hips had undergone component revisions. The reasons for revision included infection in 1 hip, dislocation with loosening in 2 hips, alumina liner fractures in 2 hips, and cup dissociation in 1 hip. All femoral and acetabular components showed no loosening in the unrevised hips at the time of the last follow-up. None of the 29 unrevised hips had osteolysis.

Good mid-term clinical results of a cemented dual mobility cup: a single-centre experience

2017 ◽  
Vol 28 (1) ◽  
pp. 59-62 ◽  
Author(s):  
Gregor Kavčič ◽  
Pika Mirt ◽  
Klemen Bedenčič
Keyword(s):  
Final Analysis ◽  
Clinical Results ◽  
Harris Hip Score ◽  
Consecutive Series ◽  
Dual Mobility Cup ◽  
Dual Mobility ◽  
Single Centre Experience ◽  
The Mean ◽  
Hip Arthroplasties

Introduction and methods: From January 2004 to December 2008, 188 total hip arthroplasties were performed using a cemented dual mobility cup. 174 patients were available for final analysis. Their mean age was 76.8 (range 54-98 years). The mean follow-up was 7.7 years (range 5-10 years). Results: There were no dislocations. Survivorship rates of the femoral and acetabular components were 100% at a minimum of 5 years. At the latest follow-up, the mean Harris Hip Score significantly increased from 31.6 (only arthritic patients) points preoperatively to 84.5 points. No patients had progressive osteolysis, component migration, or loosening on radiographs. 2 patients presented with periprosthetic fractures treated conservatively. 2 patients presented with infection treated without implant removal and 1 patient presented with transient femoral palsy. Conclusions: The results of this consecutive series confirmed the good performance of the cemented dual mobility cup at mean 7.7 years follow-up with no revision and no dislocations.

scholarly journals Salvaging Unstable or Recurrent Dislocating Total Hip Arthroplasty with the Constrained Acetabular Component

2002 ◽  
Vol 10 (2) ◽  
pp. 165-169 ◽  
Author(s):  
DA Stanton ◽  
WJ Bruce ◽  
JA Goldberg ◽  
W Walsh
Keyword(s):  
Total Hip Arthroplasty ◽  
Acetabular Component ◽  
Hip Arthroplasty ◽  
Recurrent Dislocation ◽  
Total Hip ◽  
Hip Replacements ◽  
The Mean ◽  
Acetabular Components ◽  
Constrained Acetabular Component

Purpose. To review cases of implantation of constraining acetabular components for unstable or recurrent dislocating total hip arthroplasty at the Department of Orthopaedics, Concord Hospital, Sydney. Methods. A retrospective analysis was performed on prospectively collected data of 13 consecutively enrolled patients. Results. From 1989 to 2000, 13 constraining acetabular components were implanted into 13 patients as a revision procedure. The surgical approach for the implantation of the constrained liner was posterolateral in 11 cases; a modified Hardinge approach was applied in 2 cases. The mean clinical follow-up duration was 43 months (range, 14–121 months) and the mean age at the time of surgery was 73 years (range, 52–84 years). No patients were lost to follow-up. Indications for using the constrained acetabular component were recurrent dislocation in revision hip replacements (n=8), and intra-operative instability (n=5). There were no episodes of dislocation of the constrained arthroplasty. In 7 cases, the constrained component was implanted into a previously well-fixed shell. Conclusion. We recommend the judicious use of the constrained component in cases of hip instability during or after total hip arthroplasty when other methods are not successful.

Hip resurfacing with a highly cross-linked polyethylene acetabular liner and a titanium nitride-coated femoral component

2018 ◽  
Vol 28 (4) ◽  
pp. 422-428 ◽  
Author(s):  
James W Pritchett
Keyword(s):  
Titanium Nitride ◽  
Femoral Component ◽  
Acetabular Component ◽  
Polyethylene Wear ◽  
Hip Resurfacing ◽  
Harris Hip Score ◽  
Kaplan Meier ◽  
Joint Biomechanics ◽  
Cementless Femoral Component ◽  
The Mean

Aims: This study evaluated a specific hip resurfacing system to determine the: (1) function and complications, (2) implant survivorship, (3) acetabular bone conservation and joint biomechanics and (4) osteolysis and polyethylene wear. Methods: I performed 234 resurfacing procedures (192 patients) using a two-piece titanium acetabular component with a 4 mm highly cross-linked polyethylene liner and a cementless titanium nitride-coated titanium femoral component. Function was assessed with Harris Hip, WOMAC, SF-12, and UCLA scores. Radiography and CT scans were used to evaluate bone retention, component position, joint biomechanics, and osteolysis. Retrieved polyethylene liners were analyzed for wear. Results: Median follow-up was 8 years and patients averaged 48 years of age at surgery. The mean Harris Hip Score was 96 and all scores improved significantly. Kaplan-Meier survivorship was 97%. The mean medial acetabular thickness was 9 mm postoperatively versus 14 mm preoperatively ( p = 0.019). Femoral bone conservation (head:neck ratio) was 1.36 postoperatively versus 1.42 preoperatively ( p = 0.02). There was no polyethylene wear through or osteolysis. Eight polyethylene retrievals had a mean wear of 0.05 mm/yr. Conclusions: Resurfacing with a highly cross-linked polyethylene acetabular component and a titanium nitride-coated titanium cementless femoral component is a reliable and bone-conserving procedure at mid-term.

Highly crosslinked polyethylene wear rates and acetabular component orientation

2018 ◽  
Vol 100-B (7) ◽  
pp. 891-897 ◽  
Author(s):  
M. G. Teeter ◽  
B. A. Lanting ◽  
D. D. Naudie ◽  
R. W. McCalden ◽  
J. L. Howard ◽  
...  
Keyword(s):  
Wear Rate ◽  
Acetabular Component ◽  
Inclination Angle ◽  
Polyethylene Wear ◽  
Safe Zone ◽  
Anteversion Angle ◽  
Median Difference ◽  
Head Penetration ◽  
The Mean ◽  
Acetabular Components

Aims The aim of this study was to determine whether there is a difference in the rate of wear between acetabular components positioned within and outside the ‘safe zones’ of anteversion and inclination angle. Patients and Methods We reviewed 100 hips in 94 patients who had undergone primary total hip arthroplasty (THA) at least ten years previously. Patients all had the same type of acetabular component with a bearing couple which consisted of a 28 mm cobalt-chromium head on a highly crosslinked polyethylene (HXLPE) liner. A supine radiostereometric analysis (RSA) examination was carried out which acquired anteroposterior (AP) and lateral paired images. Acetabular component anteversion and inclination angles were measured as well as total femoral head penetration, which was divided by the length of implantation to determine the rate of polyethylene wear. Results The mean anteversion angle was 19.4° (-15.2° to 48°, sd 11.4°), the mean inclination angle 43.4° (27.3° to 60.5°, sd 6.6°), and the mean wear rate 0.055 mm/year (sd 0.060). Exactly half of the hips were positioned inside the ‘safe zone’. There was no difference (median difference, 0.012 mm/year; p = 0.091) in the rate of wear between acetabular components located within or outside the ‘safe zone’. When compared to acetabular components located inside the ‘safe zone’, the wear rate was no different for acetabular components that only achieved the target anteversion angle (median difference, 0.012 mm/year; p = 0.138), target inclination angle (median difference, 0.013 mm/year; p = 0.354), or neither target (median difference, 0.012 mm/year; p = 0.322). Conclusion Placing the acetabular component within or outside the ‘safe zone’ did not alter the wear rate of HXLPE at long-term follow-up to a level that risked osteolysis. HXLPE appears to be a forgiving bearing material in terms of articular surface wear, but care must still be taken to position the acetabular component correctly so that the implant is stable. Cite this article: Bone Joint J 2018;100-B:891-7.

Higher UHMWPE wear-rate in cementless compared with cemented cups with the Saturne® Dual-Mobility acetabular system

2018 ◽  
Vol 28 (2) ◽  
pp. 125-132 ◽  
Author(s):  
Steffan Tabori-Jensen ◽  
Christina Frølich ◽  
Torben B. Hansen ◽  
Søren Bøvling ◽  
Morten Homilius ◽  
...  
Keyword(s):  
Wear Rate ◽  
Polyethylene Wear ◽  
Walking Distance ◽  
Harris Hip Score ◽  
Evaluation Activity ◽  
Dual Mobility ◽  
Time Of Surgery ◽  
Activity Measurements ◽  
The Mean

Introduction: Dual mobility (DM) total hip arthroplasty (THA) may reduce dislocation risk, but might increase the risk of high polyethylene (PE) wear due to double wearing surfaces. Methods: 127 patients (97 female) with 129 hips operated with THA after displaced femoral neck fracture FNF between 2005 and 2011, were seen for a cross-sectional clinical follow-up. Acetabular components were Saturne® DM cups with 28mm chrome-cobalt heads in UHMWPE. Cementless cups (n = 73) were hydroxyapatite coated. Radiographs were obtained for analysis of cup placement, 2D polyethylene wear and wear-rate (PolyWare 3D), and further radiological evaluation. Activity measurements included Timed Up and Go test (TUG) and walking distance from Harris Hip Score (HHS). Results: At a mean follow-up of 2.83 (1.0-7.7) years the mean wear was 0.82 mm (range 0.17-4.51, SD 0.50), and the wear-rate was 0.37 mm (range 0.06-1.90, SD 0.29). Wear-rate of 0.43 mm/year (SD 0.30) in cementless cups was higher (p = 0.004) than 0.30 mm/year (SD 0.27) in cemented cups. Mean age at time of surgery was 75.1 years (range 30-95). There was no correlation between age at time of surgery and wear (p = 0.56). There was no correlation between cup inclination and wear-rate (p = 0.35). TUG was mean 13.4 seconds (range 4.5-30.1) and correlated with wear rate (p = 0.03). Conclusions: At short term follow-up, the mean wear-rate in old and low demand patients was high, correlated to activity, and was above the generally accepted osteolysis threshold (0.1 mm/yr.). Cementless HA-coated cups had higher wear-rate than cemented cups.

scholarly journals A double mobility acetabular implant for primary hip arthroplasty in patients at high risk of dislocation

2014 ◽  
Vol 96 (8) ◽  
pp. 597-601 ◽  
Author(s):  
NL Vasukutty ◽  
RG Middleton ◽  
P Young ◽  
C Uzoigwe ◽  
B Barkham ◽  
...  
Keyword(s):  
High Risk ◽  
Acetabular Component ◽  
Polyethylene Wear ◽  
Large Diameter ◽  
Wear Rates ◽  
Total Hip ◽  
Hip Function ◽  
The Mean ◽  
Acetabular Implant

Introduction Dislocation following total hip replacement continues to be a problem for which no completely satisfactory solution has been found. Several methods have been proposed to reduce the incidence of hip dislocations with varying degrees of success, including elevated rim liners, constrained liners and large diameter bearings. We present our experience with the double mobility acetabular component in patients at high risk of instability. Methods This was a retrospective review of 65 primary total hip arthroplasties in 55 patients (15 men, 40 women), performed between October 2005 and November 2009. The majority (80%) of patients had at least two and 26% had at least three risk factors for instability. The mean age was 76 years (range: 44–92 years). The patients were followed up for a mean duration of 60 months (range: 36–85 months). Results Fourteen patients died and one was lost to follow-up, leaving fifty hips for final assessment. Until the final follow-up appointment, no patients had dislocation and none required revision surgery. The mean Oxford hip score improved from 45.0 to 26.5 (p<0.0001). The mean Merle d’Aubigné pain score improved from 1.4 to 4.9 (p<0.0001), the walking score from 2.3 to 3.1 (p<0.07) and the absolute hip function score from 5.4 to 10.8 (p<0.0001). There were no clinical or radiographic signs of loosening. Conclusions The double mobility acetabular component was successful at preventing dislocation during early to medium-term follow-up. However, as data are still lacking with regard to polyethylene wear rates at the additional bearing surface, it would be prudent to restrict the use of this implant to selected patients at high risk of instability.

The Use of Basket and Cross Shell Reinforcement in Revision Acetabulum Arthroplasty

2018 ◽  
Vol 20 (2) ◽  
pp. 123-131
Author(s):  
Andrzej Pozowski ◽  
Mateusz Kowal ◽  
Patryk Pozowski ◽  
Małgorzata Paprocka-Borowicz
Keyword(s):  
Average Duration ◽  
Clinical Results ◽  
Harris Hip Score ◽  
Acetabular Bone ◽  
Huge Data ◽  
Biological Capacity ◽  
The Mean ◽  
Revision Operations ◽  
Basic Prerequisite

Background. In spite of many decades of experience and huge data resources to evaluate the results of increasingly difficult and extensive acetabulum revision operations, it is not possible to obtain fully satisfactory results. This article presents the indications for use, surgical technique, and distant and intermediate-range results in the operation of replacing a loosened acetabular component of an endoprosthesis with accompanying extensive cavitary or segmental floor defects. Material and methods. A retrospective evaluation was performed on 65 hips in 55 patients, including bila­teral procedures in 8 women and 2 men, operated on between 1994 and 2012. The mean age of the patients at the time of surgery was 66 +/- 16 years. The average duration of follow-up was 9 years and 3 months. Results. Clinical results at 36 months from the surgery showed that the Harris Hip Score had increased by a mean of 47.2 HHS points and the WOMAC index had increased by 37.7 points. Conclusions. 1. The use of the method described in the article in selected cases produces good and excellent results, especially with the use of double reinforcement. 2. A basic prerequisite for the use of the basket is stable support for at least 3 arms of the basket on the acetabular bone reinforcement ring and good protection of grafts in the bone stock with sufficient biological capacity.

scholarly journals Early low complication rate of ceramic-on-ceramic total hip arthroplasty by direct anterior approach

SICOT-J ◽  
2020 ◽  
Vol 6 ◽  
pp. 30 ◽  
Author(s):  
Paul Henri Bauwens ◽  
Camdon Fary ◽  
Elvire Servien ◽  
Sébastien Lustig ◽  
Cécile Batailler
Keyword(s):  
Clinical Outcomes ◽  
Anterior Approach ◽  
Polyethylene Wear ◽  
Direct Anterior Approach ◽  
Late Complications ◽  
Harris Hip Score ◽  
Total Hip ◽  
The Mean ◽  
Ceramic On Ceramic

Introduction: Ceramic-on-ceramic couplings are an alternative bearing surface to reduce the problems related to polyethylene wear and debris. However, ceramic articulations have their own risk of unique complications: fracture, squeaking, or dislocation. Few studies have assessed the outcomes of ceramic-on-ceramic total hip arthroplasties (THA) by direct anterior approach (DAA). The aim was to evaluate the early complications and revision rate of ceramic-on-ceramic THA by DAA. Material: A retrospective single-center study of 116 consecutive THAs was performed by DAA (106 patients) with ceramic-on-ceramic bearing from January 2015 to February 2018 with a minimum 24 months of follow-up. No patients were lost to follow-up. The mean age was of 55.3 years ± 11.3. The same cementless acetabular shell with a Biolox Delta ceramic insert and head were used. The complication and revision rates were collected at the last follow-up. The positioning of the acetabular implant was assessed on standard radiographs. Postoperative clinical outcomes were assessed by the Harris Hip Score. Results: At a mean follow-up of 31.9 months ± 5.5, no THA was revised. Five patients had late complications: 3 squeaking (2.6%) and 2 psoas impingements (1.7%) and were managed conservatively. All patients had satisfactory bony ingrowth of acetabular component, with no radiolucent lines and no osteolysis. Eight patients (6.9%) had an anterior overhang of the cup. The mean overhang for these patients was 4.1 mm. 111 hips (96%) were perceived as forgotten or having no limitations. Conclusion: This ceramic-on-ceramic coupling and shell by DAA produced excellent clinical outcomes and implant survival rate at a minimum two-year follow-up study. No serious complication was observed during the follow-up.

scholarly journals Hip Arthroplasty in Patients with Hip Dysplasia by Individual Augments: Early Results

2020 ◽  
Vol 26 (2) ◽  
pp. 50-59
Author(s):  
Ya. A. Rukin ◽  
A. V. Lychagin ◽  
V. Yu. Murylev ◽  
A. V. Garkavi ◽  
D. A. Tarasov ◽  
...  
Keyword(s):  
Femoral Head ◽  
Acetabular Component ◽  
Hip Arthroplasty ◽  
Hip Dysplasia ◽  
Harris Hip Score ◽  
Center Of Rotation ◽  
Anatomical Position ◽  
Early Results ◽  
Acetabular Components

Relevance. The altered hip anatomy makes total hip arthroplasty in patients with hip dysplasia a difficult and non-standard task. The acetabulum is deformed with femoral head in subluxation or dislocation. The most important task of surgery is to restore the anatomical position of the hip center of rotation.The study purpose — to evaluate the early results of hip arthroplasty with individual augments in the patients with hip dysplasia.Materials and Methods. Since 2017, nine patients with hip dysplasia have undergone surgery using individually printed augments. All patients were women with average age 51.3±14.5 years (23 to 67). The mean follow-up was 14.3±5.2 months (8 to 20). Patients were evaluated using follow-up X-rays, a visual analogue scale (VAS), Harris Hip Score (HHS), and Western Ontario and McMaster Universities Arthritis Index (WOMAC).Results. There was no a single case of endoprosthesis dislocation, loosening of components, prosthetic infection or revision surgery in the analyzed group of patients. The planned sizes of the acetabular components were equal to the placed in 7 cases (77.8%). In two cases (22.2%), the acetabular components were 2 mm larger because the surgeon wanted a greater degree of press-fit fixation. The restoration of the anatomical position of the acetabular component was noted. Before the surgery, the femoral head was on average 22.7±11.7 mm (10 to 43 mm) higher. After the surgery, the level of the acetabular component was on average only 0.75±2.1 mm (1.7 to 5 mm), p = 0.008. Also, there were a decrease in pain and quality of life improvement by VAS from 6.78±1.39 before surgery to 2.22±1.09 at follow-up (p = 0.007), HHS increase from 30.5±18. 1 to 77.59±14.26 (p = 0.008), and WOMAC decrease from 73.3±14.1 to 18.22±8.2 (p = 0.008).Conclusion. The individually printed augments have shown high efficacy for restoration of the anatomical center of rotation and good early results in the patients with hip dysplasia undergone hip arthroplasty.

Sign in / Sign up

Export Citation Format

Share Document