Hot Spot Stress Analysis of Fatigue for Tsing Ma Bridge Critical Members under Traffic Using Finite Element Method

2007 ◽  
Vol 353-358 ◽  
pp. 925-928 ◽  
Author(s):  
Tai Quan Zhou ◽  
Tommy Hung Tin Chan
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Analysis ◽  
Hot Spot ◽  
Suspension Bridge ◽  
Element Analysis ◽  
Hot Spot Stress ◽  
Traffic Loading ◽  
Tsing Ma Bridge ◽  
Fatigue Evaluation

The suspension bridge has more flexibility and repetitive vehicles produce stress cycles in members. Then fatigue of the member is accumulated with the daily traffic loadings. In order to evaluate the working condition of the Tsing Ma Bridge, the online monitoring health system has been installed in long suspension bridge. The location of the strain sensor is not exactly at the critical member locations. The hot spot stress analysis for critical members is necessary for accurate fatigue evaluation of the bridge. The global finite element analysis of the Tsing Ma Bridge under traffic loading is performed to determine the critical fatigue member locations. A detailed local finite element analysis for the welded connections is performed to determine the hot spot stress of critical fatigue location. As a case for study, the calculated stress concentration factor is combined with the nominal representative stress block cycle to obtain the representative hot spot stress range cycle block under traffic loading from online health monitoring system. The comparison result shows that the nominal stress approach cannot consider the most critical stress of the fatigue damage location and the hot spot stress approach is more appropriate for fatigue evaluation.

scholarly journals Use of 3D Scan of Weld Joint in Finite Element Analysis and Stochastic Analysis of Hot-Spot Stresses in Tubular Joint for Fatigue Life Estimation

2019 ◽  
Author(s):  
Mikkel L. Larsen ◽  
Vikas Arora ◽  
Marie Lützen ◽  
Ronnie R. Pedersen ◽  
Eric Putnam
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Welded Joints ◽  
Hot Spot ◽  
Strain Range ◽  
Fe Model ◽  
Design Codes ◽  
Element Analysis ◽  
Hot Spot Stress ◽  
Weld Toe

Abstract Several methods for modelling and finite element analysis of tubular welded joints are described in various design codes. These codes provide specific recommendations for modelling of the welded joints, using simple weld geometries. In this paper, experimental hot-spot strain range results from a full-scale automatically welded K-node test are compared to corresponding finite element models. As part of investigating the automatically welded K-joint, 3D scans of the weld surfaces have been made. These scans are included in the FE models to determine the accuracy of the FE models. The results are compared to an FE model with a simple weld geometry based on common offshore design codes and a model without any modelled weld. The results show that the FE model with 3D scanned welds is more accurate than the two simple FE models. As the weld toe location of the 3D scanned weld is difficult to locate precisely in the FE model and as misplacement of strain gauges are possible, stochastic finite element modelling is performed to analyse the resulting probabilistic hot-spot stresses. The results show large standard deviations, showing the necessity to evaluate the hot-spot stress method when using 3D scanned welds.

Finite Element Analysis of Drum on the New Type Self-Driven Towing Machine for Cable

2011 ◽  
Vol 55-57 ◽  
pp. 664-669
Author(s):  
Jin Ning Nie ◽  
Hui Wang ◽  
De Feng Xie
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Analysis ◽  
Compressive Stress ◽  
Wire Rope ◽  
Ansys Software ◽  
Element Analysis ◽  
Structure Improvement ◽  
Improvement Measures ◽  
New Type

According to the situation that the dual-friction drums on the new type towing machine lack stress analysis when designed, the safety is difficult to test and verify. The pull of wire rope in various positions was derived and calculated, so both compressive stress and tangent friction force generated by the pull of wire rope were calculated. The result made by ANSYS software demonstrates the safety of the left drum which suffers from larger loads, structure improvement measures are put forward for the drum.

Stress Analysis and Structure Optimization for the Opening Flat Cover of Pressure Vessels

2012 ◽  
Vol 538-541 ◽  
pp. 3253-3258 ◽  
Author(s):  
Jun Jian Xiao
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Concentration ◽  
Stress Analysis ◽  
Structure Optimization ◽  
Pressure Vessels ◽  
Secondary Stress ◽  
Element Analysis ◽  
Primary Stress ◽  
Flat Cover

According to the results of finite element analysis (FEA), when the diameter of opening of the flat cover is no more than 0.5D (d≤0.5D), there is obvious stress concentration at the edge of opening, but only existed within the region of 2d. Increasing the thickness of flat covers could not relieve the stress concentration at the edge of opening. It is recommended that reinforcing element being installed within the region of 2d should be used. When the diameter of openings is larger than 0.5D (d>0.5D), conical or round angle transitions could be employed at connecting location, with which the edge stress decreased remarkably. However, the primary stress plus the secondary stress would be valued by 3[σ].

Strength-based design of a sunflower stalk cutter machine design using finite element analysis and experimental validation

2021 ◽  
pp. 095440622110597
Author(s):  
Gürkan İrsel
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Analysis ◽  
Strain Gage ◽  
Experimental Validation ◽  
Experimental Studies ◽  
Fatigue Analysis ◽  
Structural Stress ◽  
Element Analysis ◽  
Strength Based

In this study, the total algorithm of the strength-based design of the system for mass production has been developed. The proposed algorithm, which includes numerical, analytical, and experimental studies, was implemented through a case study on the strength-based structural design and fatigue analysis of a tractor-mounted sunflower stalk cutting machine (SSCM). The proposed algorithm consists of a systematic engineering approach, material selection and testing, design of the mass criteria suitability, structural stress analysis, computer-aided engineering (CAE), prototype production, experimental validation studies, fatigue calculation based on an FE model and experimental studies (CAE-based fatigue analysis), and an optimization process aimed at minimum weight. Approximately 85% of the system was designed using standard commercially available cross-section beams and elements using the proposed algorithm. The prototype was produced, and an HBM data acquisition system was used to collect the strain gage output. The prototype produced was successful in terms of functionality. Two- and three-dimensional mixed models were used in the structural analysis solution. The structural stress analysis and experimental results with a strain gage were 94.48% compatible in this study. It was determined using nCode DesignLife software that fatigue damage did not occur in the system using the finite element analysis (FEA) and experimental data. The SSCM design adopted a multi-objective genetic algorithm (MOGA) methodology for optimization with ANSYS. With the optimization solved from 422 iterations, a maximum stress value of 57.65 MPa was determined, and a 97.72 kg material was saved compared to the prototype. This study provides a useful methodology for experimental and advanced CAE techniques, especially for further study on complex stress, strain, and fatigue analysis of new systematic designs desired to have an optimum weight to strength ratio.

Sign in / Sign up

Export Citation Format

Share Document