Oxford HEXameter: Laboratory High Energy X-Ray Diffractometer for Bulk Residual Stress Analysis

2006 ◽  
Vol 524-525 ◽  
pp. 743-748 ◽  
Author(s):  
Alexander M. Korsunsky ◽  
Shu Yan Zhang ◽  
Daniele Dini ◽  
Willem J.J. Vorster ◽  
Jian Liu
Keyword(s):  
Accurate Determination ◽  
High Energy ◽  
Energy Dispersive ◽  
Detector Response ◽  
X Rays ◽  
X Ray Diffraction ◽  
X Ray ◽  
New Instrument ◽  
Synchrotron Beamlines

Diffraction of penetrating radiation such as neutrons or high energy X-rays provides a powerful non-destructive method for the evaluation of residual stresses in engineering components. In particular, strain scanning using synchrotron energy-dispersive X-ray diffraction has been shown to offer a fast and highly spatially resolving measurement technique. Synchrotron beamlines provide best available instruments in terms of flux and low beam divergence, and hence spatial and measurement resolution and data collection rate. However, despite the rapidly growing number of facilities becoming available in Europe and across the world, access to synchrotron beamlines for routine industrial and research use remains regulated, comparatively slow and expensive. A laboratory high energy X-ray diffractometer for bulk residual strain evaluation (HEXameter) has been developed and built at Oxford University. It uses a twin-detector setup first proposed by one of the authors in the energy dispersive X-ray diffraction mode and allows simultaneous determination of macroscopic and microscopic strains in two mutually orthogonal directions that lie approximately within the plane normal to the incident beam. A careful procedure for detector response calibration is used in order to facilitate accurate determination of lattice parameters by pattern refinement. The results of HEXameter measurements are compared with synchrotron X-ray data for several samples e.g. made from a titanium alloy and a particulate composite with an aluminium alloy matrix. Experimental results are found to be consistent with synchrotron measurements and strain resolution close to 2×10-4 is routinely achieved by the new instrument.

Energy-Dispersive X-Ray Techniques for Accurate Heavy Element Assay

1986 ◽  
Vol 30 ◽  
pp. 285-292 ◽  
Author(s):  
H. Ottmar ◽  
H. Eberle ◽  
P. Matussek ◽  
I. Michel-Piper
Keyword(s):  
Absorption Edge ◽  
Heavy Element ◽  
Accurate Determination ◽  
Energy Dispersive ◽  
X Rays ◽  
Specific Absorption ◽  
X Ray ◽  
Xrf Analysis ◽  
Analysis Technique

Energy-dispersive X-ray techniques can be employed in two different ways for the accurate determination of element concentrations in specimens: (1) spectrometry of fluoresced characteristic X-rays as widely applied in the various modes of the traditional XRF analysis technique, and (2) spectrometry of the energy-differential transmittance of an X-ray continuum at the element-specific absorption-edge energies.

Phase composition depth profiles using spatially resolved energy dispersive X-ray diffraction

2004 ◽  
Vol 37 (6) ◽  
pp. 967-976 ◽  
Author(s):  
Andrew C. Jupe ◽  
Stuart R. Stock ◽  
Peter L. Lee ◽  
Nikhila N. Naik ◽  
Kimberly E. Kurtis ◽  
...  
Keyword(s):  
Phase Composition ◽  
Spatial Resolution ◽  
Zinc Coating ◽  
High Energy ◽  
Sulfate Attack ◽  
Energy Dispersive ◽  
X Ray Diffraction ◽  
X Ray ◽  
Spatially Resolved ◽  
Composition Profiles

Spatially resolved energy dispersive X-ray diffraction, using high-energy synchrotron radiation (∼35–80 keV), was used nondestructively to obtain phase composition profiles along the radii of cylindrical cement paste samples to characterize the progress of the chemical changes associated with sulfate attack on the cement. Phase distributions were acquired to depths of ∼4 mm below the specimen surface with sufficient spatial resolution to discern features less than 200 µm thick. The experimental and data analysis methods employed to obtain quantitative composition profiles are described. The spatial resolution that could be achieved is illustrated using data obtained from copper cylinders with a thin zinc coating. The measurements demonstrate that this approach is useful for nondestructively visualizing the sometimes complex transformations that take place during sulfate attack on cement-based materials. These transformations can be spatially related to microstructure as seen by computed microtomography.

scholarly journals Electronic Excitations and Radiation Damage in Macromolecular Crystallography

Crystals ◽  
2018 ◽  
Vol 8 (7) ◽  
pp. 273 ◽  
Author(s):  
José Brandão-Neto ◽  
Leonardo Bernasconi
Keyword(s):  
Chemical Information ◽  
X Rays ◽  
Electronic Excitations ◽  
Macromolecular Crystallography ◽  
X Ray Diffraction ◽  
X Ray ◽  
Atomic Structures ◽  
Successful Approach ◽  
Structural Research

Macromolecular crystallography at cryogenic temperatures has so far provided the majority of the experimental evidence that underpins the determination of the atomic structures of proteins and other biomolecular assemblies by means of single crystal X-ray diffraction experiments. One of the core limitations of the current methods is that crystal samples degrade as they are subject to X-rays, and two broad groups of effects are observed: global and specific damage. While the currently successful approach is to operate outside the range where global damage is observed, specific damage is not well understood and may lead to poor interpretation of the chemistry and biology of the system under study. In this work, we present a phenomenological model in which specific damage is understood as the result of a single process, the steady excitation of crystal electrons caused by X-ray absorption, which acts as a trigger for the bulk effects that manifest themselves in the form of global damage and obscure the interpretation of chemical information from XFEL and synchrotron structural research.

A high-energy triple-axis X-ray diffractometer for the study of the structure of bulk crystals

2004 ◽  
Vol 37 (6) ◽  
pp. 901-910 ◽  
Author(s):  
C. Seitz ◽  
M. Weisser ◽  
M. Gomm ◽  
R. Hock ◽  
A. Magerl
Keyword(s):  
High Energy ◽  
X Rays ◽  
Bulk Crystals ◽  
X Ray Diffraction ◽  
X Ray ◽  
Peak Intensity ◽  
High Penetration ◽  
Massive Sample ◽  
Laue Geometry ◽  
The Ideal

A triple-axis diffractometer for high-energy X-ray diffraction is described. A 450 kV/4.5 kW stationary tungsten X-ray tube serves as the X-ray source. Normally, 220 reflections of thermally annealed Czochralski Si are employed for the monochromator and analyser. Their integrated reflectivity is about ten times higher than the ideal crystal value. With the same material as the sample, and working with the WKα line at 60 keV in symmetric Laue geometry for all axes, the full width at half-maximum (FWHM) values for the longitudinal and transversal resolution are 2.5 × 10−3and 1.1 × 10−4for ΔQ/Q, respectively, and the peak intensity for a non-dispersive setting is 3000 counts s−1. In particular, for a double-axis mode, an energy well above 100 keV from theBremsstrahlungspectrum can be used readily. High-energy X-rays are distinguished by a high penetration power and materials of several centimetre thickness can be analysed. The feasibility of performing experiments with massive sample environments is demonstrated.

scholarly journals Electronic Excitations and Radiation Damage in Macromolecular Crystallography

2018 ◽  
Author(s):  
José Brandão-Neto ◽  
Leonardo Bernasconi
Keyword(s):  
Chemical Information ◽  
X Rays ◽  
Electronic Excitations ◽  
Macromolecular Crystallography ◽  
X Ray Diffraction ◽  
X Ray ◽  
Atomic Structures ◽  
Successful Approach ◽  
Structural Research

Macromolecular crystallography at cryogenic temperatures has so far provided the majority of the experimental evidence that underpins the determination of the atomic structures of proteins and other biomolecular assemblies by means of single crystal X-ray diffraction experiments. One of the core limitations of the current methods is that crystal samples degrade as they are subject to X-rays, and two broad groups of effects are observed: global and specific damage. While the currently successful approach is to operate outside the range where global damage is observed, specific damage is not well understood and may lead to poor interpretation of the chemistry and biology of the system under study. In this work, we present a phenomenological model in which specific damage is understood as the result of a single process, the steady excitation of crystal electrons caused by X-ray absorption, which acts as a trigger for the bulk effects that manifest themselves in the form of global damage and obscure the interpretation of chemical information from XFEL and synchrotron structural research.

Layer stacking disorder in Mg-Fe chlorites based on powder X-ray diffraction data

2020 ◽  
Vol 105 (3) ◽  
pp. 353-362
Author(s):  
Katarzyna Luberda-Durnaś ◽  
Marek Szczerba ◽  
Małgorzata Lempart ◽  
Zuzanna Ciesielska ◽  
Arkadiusz Derkowski
Keyword(s):  
Accurate Determination ◽  
Unit Cell ◽  
Powder Xrd ◽  
X Ray Diffraction ◽  
Unit Cell Parameters ◽  
Xrd Pattern ◽  
X Ray ◽  
Cell Parameters ◽  
Layer Stacking

Abstract The primary aim of this study was the accurate determination of unit-cell parameters and description of disorder in chlorites with semi-random stacking using common X-ray diffraction (XRD) data for bulk powder samples. In the case of ordered chlorite structures, comprehensive crystallographic information can be obtained based on powder XRD data. Problems arise for samples with semi-random stacking, where due to strong broadening of hkl peaks with k ≠ 3n, the determination of unit-cell parameters is demanding. In this study a complete set of information about the stacking sequences in chlorite structures was determined based on XRD pattern simulation, which included determining a fraction of layers shifted by ±1/3b, interstratification with different polytypes and 2:1 layer rotations. A carefully selected series of pure Mg-Fe tri-trioctahedral chlorites with iron content in the range from 0.1 to 3.9 atoms per half formula unit cell was used in the study. In addition, powder XRD patterns were carefully investigated for the broadening of the odd-number basal reflections to determine interstratification of 14 and 7 Å layers. These type of interstratifications were finally not found in any of the samples. This result was also confirmed by the XRD pattern simulations, assuming interstratification with R0 ordering. Based on h0l XRD reflections, all the studied chlorites were found to be the IIbb polytype with a monoclinic-shaped unit cell (β ≈ 97°). For three samples, the hkl reflections with k ≠ 3n were partially resolvable; therefore, a conventional indexing procedure was applied. Two of the chlorites were found to have a monoclinic cell (with α, γ = 90°). Nevertheless, among all the samples, the more general triclinic (pseudomonoclinic) crystal system with symmetry C1 was assumed, to calculate unit-cell parameters using Le Bail fitting. A detailed study of semi-random stacking sequences shows that simple consideration of the proportion of IIb-2 and IIb-4/6 polytypes, assuming equal content of IIb-4 and IIb-6, is not sufficient to fully model the stacking structure in chlorites. Several, more general, possible models were therefore considered. In the first approach, a parameter describing a shift into one of the ±1/3b directions (thus, the proportion of IIb-4 and IIb-6 polytypes) was refined. In the second approach, for samples with slightly distinguishable hkl reflections with k ≠ 3n, some kind of segregation of individual polytypes (IIb-2/4/6) was considered. In the third approach, a model with rotations of 2:1 layers about 0°, 120°, 240° was shown to have the lowest number of parameters to be optimized and therefore give the most reliable fits. In all of the studied samples, interstratification of different polytypes was revealed with the fraction of polytypes being different than IIbb ranging from 5 to 19%, as confirmed by fitting of h0l XRD reflections.

scholarly journals The X-ray stellar population of the LMC

2008 ◽  
Vol 4 (S256) ◽  
pp. 20-29 ◽  
Author(s):  
Yaël Nazé
Keyword(s):  
Stellar Population ◽  
Main Sequence ◽  
Massive Stars ◽  
High Energy ◽  
Magellanic Clouds ◽  
X Rays ◽  
X Ray ◽  
Energy Domain ◽  
X Ray Binaries

AbstractIn the study of stars, the high energy domain occupies a place of choice, since it is the only one able to directly probe the most violent phenomena: indeed, young pre-main sequence objects, hot massive stars, or X-ray binaries are best revealed in X-rays. However, previously available X-ray observatories often provided only crude information on individual objects in the Magellanic Clouds. The advent of the highly efficient X-ray facilities XMM-Newton and Chandra has now dramatically increased the sensitivity and the spatial resolution available to X-ray astronomers, thus enabling a fairly easy determination of the properties of individual sources in the LMC.

In situ time-resolved X-ray diffraction of tobermorite formation process under hydrothermal condition: Influence of reactive al compound

2011 ◽  
Vol 26 (2) ◽  
pp. 134-137 ◽  
Author(s):  
K. Matsui ◽  
A. Ogawa ◽  
J. Kikuma ◽  
M. Tsunashima ◽  
T. Ishikawa ◽  
...  
Keyword(s):  
Hydrothermal Reaction ◽  
High Energy ◽  
Saturated Steam ◽  
Array Detector ◽  
Time Interval ◽  
X Rays ◽  
X Ray Diffraction ◽  
Formation Reaction ◽  
X Ray

Hydrothermal formation reaction of tobermorite in the autoclaved aerated concrete (AAC) process has been investigated by in situ X-ray diffraction. High-energy X-rays from a synchrotron radiation source in combination with a newly developed autoclave cell and a photon-counting pixel array detector were used. XRD measurements were conducted in a temperature range 100–190°C throughout 12 h of reaction time with a time interval of 4.25 min under a saturated steam pressure. To clarify the tobermorite formation mechanism in the AAC process, the effect of Al addition on the tobermorite formation reaction was studied. As intermediate phases, non-crystalline calcium silicate hydrate (C-S-H), hydroxylellestadite (HE), and katoite (KA) were clearly observed. Consequently, it was confirmed that there were two reaction pathways via C-S-H and KA in the tobermorite formation reaction of Al containing system. In addition, detailed information on the structural changes during the hydrothermal reaction was obtained.

X-ray diffraction cell for studying solid–gas reactions under gas pressures to 100 bar

2006 ◽  
Vol 39 (6) ◽  
pp. 850-855 ◽  
Author(s):  
E. MacA. Gray ◽  
D. J. Cookson ◽  
T. P. Blach
Keyword(s):  
Phase Transformation ◽  
Heat Flow ◽  
Real Time ◽  
High Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Time Determination ◽  
Gas Reactions ◽  
Gas Pressures

A pressure cell designed for high-energy X-ray diffraction in transmission mode is described. The cell is intended for use at temperatures up to 573 K with samples that are large enough to permit the real-time determination of the amount of absorbed gas by measuring the gas pressure. The design is driven by the need to ensure that the sample temperature is constant and uniform, despite the heat flow accompanying the reaction between the gas and the sample. The use of the cell is illustrated by its application to elucidating the hydriding phase transformation in the LaNi5–H2system.

Sign in / Sign up

Export Citation Format

Share Document