The Effect of Grain Boundary State on Deformation Process Development in Nanostructured Metals Produced by the Methods of Severe Plastic Deformation

2011 ◽  
Vol 683 ◽  
pp. 69-79 ◽  
Author(s):  
Evgeny V. Naydenkin ◽  
Galina P. Grabovetskaya ◽  
Konstantin Ivanov
Keyword(s):  
Plastic Deformation ◽  
Grain Boundary ◽  
Severe Plastic Deformation ◽  
Deformation Process ◽  
Process Development ◽  
Grain Boundary Sliding ◽  
Total Deformation ◽  
Nanostructured Metals ◽  
Boundary State ◽  
Boundary Sliding

In this review the investigations of deformation process development are discussed which were carried out by tension and creep in the temperature range Т<0.4Tm (here Тm is the absolute melting point of material) for nanostructured metals produced by the methods of severe plastic deformation. The contribution of grain boundary sliding to the total deformation in the above temperature interval is also considered. An analysis is made of the effect of grain size and grain boundary state on the evolution of grain boundary sliding and cooperative grain boundary sliding in nanostructured metals.

Superplasticity of Aerospace 7075 (Al-Zn-Mg-Cu) Aluminium Alloy Obtained by Severe Plastic Deformation

2018 ◽  
Vol 385 ◽  
pp. 39-44 ◽  
Author(s):  
Fernando Carreño ◽  
Oscar A. Ruano
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Aluminium Alloy ◽  
Room Temperature ◽  
Grain Boundary Sliding ◽  
Strain Rates ◽  
Aerospace Applications ◽  
Boundary Sliding ◽  
Processing Stress

The 7075 (Al-Zn-Mg-Cu) aluminium alloy is the reference alloy for aerospace applications due to its specific mechanical properties at room temperature, showing excellent tensile strength and sufficient ductility. Formability at high temperature can be improved by obtaining superplasticity as a result of fine, equiaxed and highly misoriented grains prone to deform by grain boundary sliding (GBS). Different severe plastic deformation (SPD) processing routes such as ECAP, ARB, HPT and FSP have been considered and their effect on mechanical properties, especially at intermediate to high temperatures, are studied. Refined grains as fine as 100 nm and average misorientations as high as 39o allow attainment of high strain rate superplasticity (HSRSP) at lower than usual temperatures (250-300oC). It is shown that increasing misorientations are obtained with increasing applied strain, and increasing grain refinement is obtained with increasing processing stress. Thus, increasing superplastic strains at higher strain rates, lower stresses and lower temperatures are obtained with increasing processing strain and, specially, processing stress.

Effect of Grain Boundary State on Diffusion and Diffusion-Controlled Processes in Ultrafine-Grained Materials Processed by Severe Plastic Deformation

2015 ◽  
Vol 5 ◽  
pp. 111-126
Author(s):  
Evgeny V. Naydenkin ◽  
Galina P. Grabovetskaya ◽  
I.P. Mishin
Keyword(s):  
Plastic Deformation ◽  
Grain Boundary ◽  
Severe Plastic Deformation ◽  
Grain Boundaries ◽  
Experimental Studies ◽  
Boundary State ◽  
Diffusion Controlled ◽  
Ultrafine Grained ◽  
Ultrafine Grained Materials ◽  
And Diffusion

Experimental studies on the grain boundary diffusion and processes controlled by it in the ultrafine-grained metallic materials produced by various methods of severe plastic deformation are reviewed. Correlation between the increased diffusion permeability of grain boundaries and features of recrystallization and deformation development in these materials possessing the non-equilibrium state of grain boundaries formed during severe plastic deformation in the temperature range of T < 0.35Tm is demonstrated and analyzed.

Deformation Characteristics of Quasicrystalline Al–Cu–Fe Alloys

1997 ◽  
Vol 12 (8) ◽  
pp. 2043-2047 ◽  
Author(s):  
J. E. Shield ◽  
M. J. Kramer
Keyword(s):  
Grain Size ◽  
High Temperature ◽  
Grain Boundary ◽  
Deformation Process ◽  
Microstructural Analysis ◽  
Grain Boundary Sliding ◽  
High Temperature Creep ◽  
Deformation Characteristics ◽  
Boundary Sliding ◽  
Fe Alloys

The deformation characteristics of icosahedral Al–Cu–Fe quasicrystals were determined by high temperature creep experiments between 680 and 720 °C and 15 and 41 MPa. The deformation process was determined to be controlled by grain boundary mechanisms. Both the stress and grain size sensitivity exponents were found to be 2, suggesting that grain boundary sliding was the rate-controlling deformation mechanism. Microstructural analysis supported this conclusion, as no intragranular defects were produced during the deformation experiments.

Sign in / Sign up

Export Citation Format

Share Document