Determine variation of poisson ratios and thermal creep stresses and strain rates in an isotropic disc

Purpose The purpose of this paper is to present study of thermal creep stresses and strain rates in a circular disc with shaft having variable density by using Seth’s transition theory. Design/methodology/approach Seth’s transition theory is applied to the problem of thermal creep transition stresses and strain rates in a thin rotating disc with shaft having variable density by finite deformation. Neither the yield criterion nor the associated flow rule is assumed here. The results obtained here are applicable to compressible materials. If the additional condition of incompressibility is imposed, then the expression for stresses corresponds to those arising from Tresca yield condition. Findings Thermal effect increased value of radial stress at the internal surface of the rotating disc made of incompressible material as compared to tangential stress and this value of radial stress further much increases with the increase in angular speed as compared to without thermal effect. Strain rates have maximum values at the internal surface for compressible material. Originality/value The model proposed in this paper is used in mechanical and electronic devices. They have extensive practical engineering application such as in steam and gas turbines, turbo generators, flywheel of internal combustion engines, turbojet engines, reciprocating engines, centrifugal compressors and brake disks.

Download Full-text

Comparison of Recovery and Recrystallization in Stainless Steel Following Plane-Wave Shock Loading and Explosive Forming

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100069132 ◽

1970 ◽

Vol 28 ◽

pp. 428-429 ◽

Cited By ~ 2

Author(s):

J. A. Korbonski ◽

L. E. Murr

Keyword(s):

Stainless Steel ◽

Shock Loading ◽

Pressure Pulse ◽

Shock Pressure ◽

304 Stainless Steel ◽

Strain Rates ◽

Two Dimensional ◽

Aisi 304 Stainless Steel ◽

Aisi 304 ◽

Explosive Forming

Comparison of recovery rates in materials deformed by a unidimensional and two dimensional strains at strain rates in excess of 104 sec.−1 was performed on AISI 304 Stainless Steel. A number of unidirectionally strained foil samples were deformed by shock waves at graduated pressure levels as described by Murr and Grace. The two dimensionally strained foil samples were obtained from radially expanded cylinders by a constant shock pressure pulse and graduated strain as described by Foitz, et al.

Download Full-text

Solid Solution Effects and Deformation Micros trueture of Shock-Loaded Iron Manganese Alloys

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100069090 ◽

1970 ◽

Vol 28 ◽

pp. 420-421

Author(s):

A. Christou ◽

J. V. Foltz ◽

N. Brown

Keyword(s):

Solid Solution ◽

Shock Loading ◽

High Strain ◽

Local Stress ◽

Strain Rates ◽

Local Stress Concentration ◽

Bcc Metals ◽

Manganese Alloys ◽

Iron Manganese ◽

Transmission Microscope

In general, all BCC transition metals have been observed to twin under appropriate conditions. At the present time various experimental reports of solid solution effects on BCC metals have been made. Indications are that solid solution effects are important in the formation of twins. The formation of twins in metals and alloys may be explained in terms of dislocation mechanisms. It has been suggested that twins are nucleated by the achievement of local stress-concentration of the order of 15 to 45 times the applied stress. Prietner and Leslie have found that twins in BCC metals are nucleated at intersections of (110) and (112) or (112) and (112) type of planes.In this paper, observations are reported of a transmission microscope study of the iron manganese series under conditions in which twins both were and were not formed. High strain rates produced by shock loading provided the appropriate deformation conditions. The workhardening mechanisms of one alloy (Fe - 7.37 wt% Mn) were studied in detail.

Download Full-text

The effects of strain and strain rate on residual microstructures in copper

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100143687 ◽

1986 ◽

Vol 44 ◽

pp. 420-421

Author(s):

M. F. Stevens ◽

P. S. Follansbee

Keyword(s):

Strain Rate ◽

Applied Stress ◽

Threshold Stress ◽

Rate Sensitivity ◽

Viscous Drag ◽

Strain Rates ◽

Strain And Strain Rate ◽

Threshold Strength ◽

Mechanism Transition ◽

Intrinsic Strength

The strain rate sensitivity of a variety of materials is known to increase rapidly at strain rates exceeding ∼103 sec-1. This transition has most often in the past been attributed to a transition from thermally activated guide to viscous drag control. An important condition for imposition of dislocation drag effects is that the applied stress, σ, must be on the order of or greater than the threshold stress, which is the flow stress at OK. From Fig. 1, it can be seen for OFE Cu that the ratio of the applied stress to threshold stress remains constant even at strain rates as high as 104 sec-1 suggesting that there is not a mechanism transition but that the intrinsic strength is increasing, since the threshold strength is a mechanical measure of intrinsic strength. These measurements were made at constant strain levels of 0.2, wnich is not a guarantee of constant microstructure. The increase in threshold stress at higher strain rates is a strong indication that the microstructural evolution is a function of strain rate and that the dependence becomes stronger at high strain rates.

Download Full-text