scholarly journals Soft Magnetic Property of Ternary Fe-9.8Si-6.0Al Alloy Using by Recycling Fe-Si Electrical Steel Sheet Scrap

2017 ◽  
Vol 24 (1) ◽  
pp. 1-8
Author(s):  
Won Sik Hong ◽  
Hyoung Woo Yang ◽  
Ji-Yeon Park ◽  
Chulmin Oh ◽  
Woo Sung Lee ◽  
...  
Keyword(s):  
Magnetic Property ◽  
Steel Sheet ◽  
Electrical Steel ◽  
Soft Magnetic Property ◽  
Soft Magnetic ◽  
Electrical Steel Sheet

Vector magnetic property of electrical steel sheet and its influence on distributions of magnetic field and iron loss for electrical machines

2013 ◽  
Vol 33 (1/2) ◽  
pp. 14-27 ◽  
Author(s):  
Heesung Yoon ◽  
Chang Seop Koh
Keyword(s):  
Magnetic Field ◽  
Magnetic Property ◽  
Steel Sheet ◽  
Electrical Steel ◽  
Electrical Machines ◽  
Iron Loss ◽  
Element Analysis ◽  
Content Type ◽  
Electrical Steel Sheet ◽  
The Magnetic Field

Purpose – The purpose of this paper is to present the vector magnetic properties of the electrical steel sheet and investigate its influences on the magnetic field and iron loss distributions for the electrical machines. Design/methodology/approach – The vector magnetic property of the electrical steel sheet is measured by using a two-dimensional single sheet tester and modelled through an E&S vector hysteresis model to be applied to finite element analysis. Findings – The magnetic field and iron loss distributions are calculated by finite element analysis combined with the E&S vector hysteresis model for the three-phase transformer and induction motor models. Originality/value – The influences of the vector magnetic property on the electrical machines are verified by comparing with the numerical results from a scalar magnetic property.

Examination of Measurement Method for Magnetostriction of Electrical Steel Sheet with Lock-in Amplifier

2012 ◽  
Vol 132 (11) ◽  
pp. 1033-1038
Author(s):  
Yuichiro Kai ◽  
Yuji Tsuchida ◽  
Takashi Todaka ◽  
Masato Enokizono
Keyword(s):  
Measurement Method ◽  
Steel Sheet ◽  
Electrical Steel ◽  
Lock In ◽  
Electrical Steel Sheet

scholarly journals Verification of electric steel punching simulation results using microhardness

2021 ◽  
Author(s):  
Sampsa Vili Antero Laakso ◽  
Ugur Aydin ◽  
Peter Krajnik
Keyword(s):  
Plastic Deformation ◽  
High Speed ◽  
Steel Sheet ◽  
Electrical Steel ◽  
High Speed Steel ◽  
Experimental Methods ◽  
Fem Simulations ◽  
Iron Losses ◽  
Simulation Results ◽  
Electrical Steel Sheet

AbstractOne of the most dominant manufacturing methods in the production of electromechanical devices from sheet metal is punching. In punching, the material undergoes plastic deformation and finally fracture. Punching of an electrical steel sheet causes plastic deformation on the edges of the part, which affects the magnetic properties of the material, i.e., increases iron losses in the material, which in turn has a negative effect on the performance of the electromagnetic devices in the final product. Therefore, punching-induced iron losses decrease the energy efficiency of the device. FEM simulations of punching have shown significantly increased plastic deformation on the workpiece edges with increasing tool wear. In order to identify the critical tool wear, after which the iron losses have increased beyond acceptable limits, the simulation results must be verified with experimental methods. The acceptable limits are pushed further in the standards by the International Electrotechnical Commission (IEC). The new standard (IEC TS 60034-30-2:2016) has much stricter limits regarding the energy efficiency of electromechanical machines, with an IE5 class efficiency that exceeds the previous IE4 class (IEC 60034-30-1:2014) requirements by 30%. The simulations are done using Scientific Forming Technologies Corporation Deform, a finite element software for material processing simulations. The electrical steel used is M400-50A, and the tool material is Vanadis 23, a powder-based high-speed steel. Vanadis 23 is a high alloyed powder metallurgical high-speed steel with a high abrasive wear resistance and a high compressive strength. It is suitable for cold work processing like punching. In the existing literature, FEM simulations and experimental methods have been incorporated for investigating the edge deformation properties of sheared surfaces, but there is a research gap in verifying the simulation results with the experimental methods. In this paper, FEM simulation of the punching process is verified using an electrical steel sheet from real production environment and measuring the deformation of the edges using microhardness measurements. The simulations show high plastic deformation 50 μm into the workpiece edge, a result that is shown to be in good agreement with the experimental results.

Sign in / Sign up

Export Citation Format

Share Document