The Effects of Backpressure on the Performance of Internal Combustion Engine and Automobile Exhaust Thermoelectric Generator

The maximum generated power of automobile exhaust thermoelectric generator (AETEG) can be enhanced by applying inserted fins to its heat exchanger, for the temperature difference of thermoelectric modules (TEMs) is increased. However, the heat exchanger will result in undesired backpressure, which may deteriorate the performance of the internal combustion engine (ICE). To evaluate the backpressure on the performance of both the ICE and the AETEG, the model of ICE integrated with AETEG was established with the GT-power software and validated with the AETEG test bench. The heat exchangers with chaos shape and fishbone shape were proposed, their pressure drop with different engine speeds was studied, and their effects on the performance of both the AETEG and the ICE were analyzed. The results showed that compared with the fishbone-shaped structure, the pressure drop of chaos-shaped heat exchanger is larger at the same engine speed, which contributes to the increased maximum power and hot side temperature of the AETEG. Moreover, compared with the ICE without heat exchanger, the brake torque, brake power, volumetric efficiency and pumping mean effective pressure of the ICE assembled with chaos-shape and fishbone-shape heat exchanger reduce, and the corresponding brake specific fuel consumption, CO emission and CO2 emission increase because of the raised backpressure caused by the heat exchanger.

Enhancing the Thermoelectric Performance through the Mutual Interaction between Conjugated Polyelectrolytes and Single-walled Carbon Nanotubes

We present a method of constructing composites composed of conjugated polyelectrolytes (CPEs) and single-walled carbon nanotubes (SWCNTs) to obtain a high-performing flexible thermoelectric generator. In this approach, three kinds of polymers, namely, poly[(1,4-(2,5-didodecyloxybenzene)-alt-2,5-thiophene] (P1), poly[(1,4-(2,5-bis-sodium butoxysulfonate-phenylene)-alt-2,5-thiophene] (P2), and poly[(1,4-(2,5-bis-acid butoxysulfonic-phenylene)-alt-2,5-thiophene] (P3) are designed, synthesized and complexed with SWCNTs as thermoelectric composites. The electrical conductivities of CPEs/SWCNTs (P2/SWCNTs, and P3/SWCNTs) nanocomposites are much higher than those of non-CPEs/SWCNTs (P1/SWCNTs) nanocomposites. Among them, the electrical conductivity of P2/SWCNTs with a ratio of 1:4 reaches 3686 S cm-1, which is 12.4 times that of P1/SWCNTs at the same SWCNT mass ratio. Moreover, CPEs/SWCNTs composites (P2/SWCNTs) display remarkably improved thermoelectric properties with the highest power factor (PF) of 163 μW m-1 K-2. In addition, a thermoelectric generator is fabricated with P2/SWCNTs composite films, and the output power and power density of this generator reach 1.37 μW and 1.4 W m-2 (cross-section) at ΔT=70 K. This result is over three times that of the thermoelectric generator composed of non-CPEs/SWCNTs composite films (P1/SWCNTs, 0.37 μW). The remarkably improved electrical conductivities and thermoelectric properties of the CPEs/SWCNTs composites (P2/SWCNTs) are attributed to the enhanced interaction. This method for constructing CPEs/SWCNTs composites can be applied to produce thermoelectric materials and devices.

Energy and Environmental Analysis of a Solar Evacuated Tube Heat Pipe Integrated Thermoelectric Generator Using IoT

This paper investigates the solar evacuated tube heat pipe system (SEHP) coupled with a thermoelectric generator (TEG) using the internet of things (IoT). The TEGs convert heat energy into electricity through the Seebeck effect that finds application in the waste heat recovery process for the generation of power. The present work deals with the theoretical study on solar evacuated tube heat pipe integrated TEG and it is validated experimentally using with and without parabolic trough concentrating collector. And the carbon credit of the TEG system is determined to find its potential in the environmental aspect. Also, the boost type converter is used to raise the power output by increasing the voltage from the TEG for rural electrifications. However, it is found that the maximum power output due to the influence of the parabolic trough concentrator results in increased efficiency when compared with the non-concentrating SEHP-TEG system. The TEG output power can be boosted up to a maximum of 5.98 V using a power electronic boost converter. Besides, the recorded real sensor data with Arduino is implemented in the experimental process for automatic remote monitoring of the temperature.