STUDIES OF PROCESSES OF THE PRECURSOR FORMATION FOR PRODUCTION OF CuAlO NANOCERAMICS AT THE EFFECT OF DOUBLE LASER PULSES ON AD1 AND M2 ALLOYS IN THE AIR ATMOSPHERE

Проведено исследование процессов образования смешанных нанопорошков Al, оксидов меди и алюминия, прекурсоров для получения нанокерамик типа CuAlO и CuAlO при воздействии сдвоенных лазерных импульсов энергией 53 мДж и между импульсным интервалом 10 мкс на мишень, состоящую из пластинок алюминия марки АД1 и меди марки М2, склеенных между собой и помещенную в закрытую стеклянную прямоугольную кювету. Установлено, что последовательное воздействие серий сдвоенных лазерных на мишень из алюминия, а затем на мишень из меди приводит к многократному увеличению выхода субоксидов AlO, ионов и атомов алюминия и меди в лазерном факеле, направляемом на подложку, при напылении пленок, по сравнению с воздействием одиночными лазерными импульсами. Изучены процессы, происходящие на поверхности подложки при напылении пленок. Показана возможность получения прекурсоров для получения нанокерамик типа CuAlO и CuAlO. A study of formation of mixed Al nanopowders, copper and aluminum oxides, and precursors for production of CuAlO and CuAlO nanoceramics under the influence of double laser pulses with energy of 53 mJ and the interpulse interval of 10 microseconds on a target consisting of plates of aluminum grade AD1 and copper grade M2, 0,4 mm thick, glued together and placed in a closed rectangular glass cuvette. It is found that the successive exposure of a series of double laser beams to an aluminum target and then to a copper target leads to a multiple increase in the yield of AlO suboxides, aluminum and copper ions and atoms in the laser torch, compared with the exposure to single laser pulses. To better understand the hidden mechanisms of this dependence, we study the processes occurring both on the surface and in the near-surface laser plasma inside the resulting microchannel when the target is broken by a series of single and double laser pulses. The possibility of obtaining precursors for the production of nanoceramics such as CuAlO, CuAlO is shown.

Времяпролетные характеристики лазерного факела при абляции мишени MnSi в атмосфере аргона

The Langmuir-probe technique has been used to study the time-of-flight characteristics of a laser torch during MnSi-target ablation in vacuum and argon atmosphere by pulsed 532-nm laser radiation at 15-ns pulse duration. It is established that the amplitude of the signal of fast particles in the laser torch nonmonotonically depends on the buffer-gas pressure. Mechanisms determining this dependence of laser-torch characteristics on the pressure are considered. The influence of buffer-gas pressure on the ion-velocity distribution function is determined.

Circuits for Optical Based Line of Sight Voice Communication

We present here line of sight communication between a person and his neighbour with the help of optical signal produced by a laser torch which act as a carrier. It is therefore a wireless communication and the transmission can go up to 500 meters. We used photodiode to receive the signal at the receiver. The transmitter circuit comprises condenser microphone transistor amplifier BC547 followed by an op-amp stage built around µA741. When we give a voice signal from the mike, it converts the voice signal into the electrical signal. This electrical signal is fed to IC741 (op-amp) for amplification. The gain of the op-amp can be controlled with the help of 1-mega-ohm potentiometer. The AF output from IC is coupled to the base of a class B amplifier which, in turn, modulates the signal. The transmitter uses 5V power supply. However, the 3-volt laser torch (after removal of its battery) can be directly connected to the circuit-with the body of the torch connected to the class B. The photodiode converts the optical signal into electrical signal and again this signal is amplified using IC741 and a combination of class B push pull amplifiers. The receiver circuit uses an NPN photodiode as the light sensor that is followed by a two-stage transistor preamplifier and IC741 based audio Power amplifier. The receiver does not need any complicated alignment. Just keep the photodiode oriented towards the remote transmitter’s laser point and adjust the volume control for a clear sound. The sensor must not directly face the sun.