Suitability of the Subaxial Cervical Laminae for Laminar Screws in the Pediatric Population: A Radiologic Anatomical Study

<b><i>Introduction:</i></b> The laminar screw method was popularized during recent years. Since no data exist in the literature on its suitability for subaxial levels in the pediatric population, a radiologic anatomical study was planned to evaluate the suitability of the laminae for laminar screws in children. <b><i>Methods:</i></b> The laminar thicknesses from C3 to C7 were measured in axial sections in 120 pediatric patients using computed tomography. The patients were divided into 3 age-groups: ages 4–6, 7–9, and 10–12. Each age-group consisted of 20 boys and 20 girls. The suitability of the laminae was evaluated for 3.5-mm-thick commercially available screws and also for the 3-mm screws that could be produced in the future. If the height of the base of the spinous process is ≥ 9 mm, the segment was accepted as suitable for the bilateral screw, and ≥5 mm is for the unilateral screw. Additionally, laminar thickness and length were measured for possible short screws longer than 15 mm in the laminae that were distally thin but proximally thick. <b><i>Results:</i></b> The C4 and C5 levels had the thinnest (2.77 ± 0.6 mm and 2.81 ± 0.6 mm, respectively) and C7 had the thickest laminae (4.66 ± 0.6 mm) in all age-groups. No significant differences were found between boys and girls and right and left laminae. According to the age-groups, an increase in laminar thickness was possible by growing, but only C7 laminae thickness was statistically different between 10–12 and 4–6 age-groups (<i>p</i> &#x3c; 0.001). The last rate of the suitability was 9.1% for the 3.5-mm-thick screws and 13.75% for the 3-mm-thick screws after deletion of the bilateral insertion due to the short base of the spinous process and adding the possible short screws in the distally thin but proximally thick laminae. The rates increased with age, but the only statistically significant difference was found between 4–6- and 10–12-year-old age-groups (<i>p</i> &#x3c; 0.001). <b><i>Conclusions:</i></b> Laminar screws may be suitable for some levels of C7, C6, and C3 even in the young pediatric population. The use of thinner screws (3 mm) may increase the suitability rate. Therefore, laminar screw choice may be considered as a salvage method in pediatric patients, and all laminae may be evaluated individually for suitability. This study did not evaluate the safety and efficacy of the method in children, and these issues must be studied further.

BigBrain 3D atlas of cortical layers: cortical and laminar thickness gradients diverge in sensory and motor cortices

Histological atlases of the cerebral cortex, such as those made famous by Brodmann and von Economo, are invaluable for understanding human brain microstructure and its relationship with functional organization in the brain. However, these existing atlases are limited to small numbers of manually annotated samples from a single cerebral hemisphere, measured from 2D histological sections. We present the first whole-brain quantitative 3D laminar atlas of the human cerebral cortex. This atlas was derived from a 3D histological model of the human brain at 20 micron isotropic resolution (BigBrain), using a convolutional neural network to segment, automatically, the cortical layers in both hemispheres. Our approach overcomes many of the historical challenges with measurement of histological thickness in 2D and the resultant laminar atlas provides an unprecedented level of precision and detail.We utilized this BigBrain cortical atlas to test whether previously reported thickness gradients, as measured by MRI in sensory and motor processing cortices, were present in a histological atlas of cortical thickness, and which cortical layers were contributing to these gradients. Cortical thickness increased across sensory processing hierarchies, primarily driven by layers III, V and VI. In contrast, fronto-motor cortices showed the opposite pattern, with decreases in total and pyramidal layer thickness. These findings illustrate how this laminar atlas will provide a link between single-neuron morphology, mesoscale cortical layering, macroscopic cortical thickness and, ultimately, functional neuroanatomy.

Computed tomography morphometric analysis for axial and subaxial translaminar screw placement in the pediatric cervical spine

Object The management of upper cervical spinal instability in children continues to represent a technical challenge. Traditionally, a number of wiring techniques followed by halo orthosis have been applied; however, they have been associated with a high rate of nonunion and poor tolerance for the halo. Alternatively, C1–2 transarticular screws and C-2 pars/pedicle screws allow more rigid fixation, but their placement is technically demanding and associated with vertebral artery injuries. Recently, C-2 translaminar screws have been added to the armamentarium of the pediatric spine surgeon as a technically simple and biomechanically efficient means of fixation. However, the use of subaxial translaminar screws have not been described in the general pediatric population. There are no published data that describe the anatomical considerations and potential limitations of this technique in the pediatric population. Methods The cervical vertebrae of 69 pediatric patients were studied on CT scans. Laminar height and thickness were measured. Statistical analysis was performed using unpaired Student t-tests (p < 0.05) and linear regression analysis. Results The mean laminar heights at C-2, C-3, C-4, C-5, C-6, and C-7, respectively, were 9.76 ± 2.22 mm, 8.22 ± 2.24 mm, 8.09 ± 2.38 mm, 8.51 ± 2.34 mm, 9.30 ± 2.54 mm, and 11.65 ± 2.65 mm. Mean laminar thickness at C-2, C-3, C-4, C-5, C-6, and C-7, respectively, were 5.07 ± 1.07 mm, 2.67 ± 0.79 mm, 2.18 ± 0.73 mm, 2.04 ± 0.60 mm, 2.52 ± 0.66 mm, and 3.84 ± 0.96 mm. In 50.7% of C-2 laminae, the anatomy could accept at least 1 translaminar screw (laminar thickness ≥ 4 mm). Conclusions Overall, the anatomy in 30.4% of patients younger than 16 years old could accept bilateral C-2 translaminar screws. However, the anatomy of the subaxial cervical spine only rarely could accept translaminar screws. This study establishes anatomical guidelines to allow for accurate and safe screw selection and insertion. Preoperative planning with thin-cut CT and sagittal reconstruction is essential for safe screw placement using this technique.