A study of preparing silver iodide nanocolloid by electrical spark discharge method and its properties

This study employed an electric discharge machine (EDM) and the Electrical Spark Discharge Method (ESDM) to prepare silver iodide nanocolloid (AgINC). Povidone–iodine (PVP-I) was dissolved in deionized water to create a dielectric fluid. Silver material was melted using the high temperature generated by an electric arc, and the peeled-off material was reacted with PVP-I to form AgI nanoparticles (AgINPs). Six discharge pulse wave parameter combinations (Ton–Toff) were employed, and the resultant particle size and suspension of the prepared samples were examined. The results revealed that AgINPs were successfully created using the ESDM. When Ton–Toff was set at 90–90 μs, the zeta potential of the AgINC was − 50.3 mV, indicating excellent suspension stability. The AgINC particle size was 16 nm, verifying that the parameters yielded AgINPs with the smallest particle size distribution and highest zeta potential. Ultraviolet–visible spectrum analyser was performed to analyse the samples, and the spectra indicated that the characteristic wavelength was 420 nm regardless of the Ton–Toff values. X-ray diffraction analysis determined that the AgINPs exhibited two crystal structures, namely β-AgI and Ag. Transmission electron microscopy was performed and revealed that the particles were irregularly shaped and that some of the larger particles had aggregated. The crystal structure was determined to be a mixture of Ag and β-AgI, with a lattice spacing of 0.235 nm and 0.229 nm, respectively. The lattice spacing of the Ag was 0.235 nm. X-ray diffraction analysis indicated that the prepared AgINC were composed of only Ag and I; no additional chemical elements were detected.

Characteristic Analysis and Electrical Conductivity of Graphene and Graphene-Nanosilver Prepared by Electrical Spark Discharge Method

This study used an electric discharge machine (EDM) to perform the electrical spark discharge method (ESDM) to prepare a graphene colloid and a graphene-Ag colloid. The characteristic wavelengths of graphene, and graphene-Ag are both 262 nm. They had the properties of high dispersion and are unlikely to aggregate. The XRD patterns of graphene and graphene-Ag are typical carbon diffraction peak angles and crystal orientations. Graphene-Ag in DW can increase the Raman signal intensity of graphene. Regarding the graphene colloid and graphene-Ag colloid, their average sheet resistance values are 0.0329 MΩ/sq and 0.00136 MΩ/sq, respectively. Moreover, when AgNPs composited with graphene layers, the average sheet resistance is only 1/24 that of graphene layers, indicating that graphene-Ag has superior conductivity.

A Study of Nanosilver Colloid Prepared by Electrical Spark Discharge Method and Its Antifungal Control Benefits

This is a study of an antimicrobial test, including yeast, Aspergillus Niger, and Aspergillus Flavus, on a nanosilver colloid solution. The antibiosis is compared with a standard silver ion solution at the same concentration as in the experimental process. This study proved that the nanosilver colloid prepared by the electrical spark discharge method (ESDM) is free of any chemical additives, has a microbial control effect, and that the effect is much better than the Ag+ standard solution at the same concentration. 3M Count Plate (YM) is used to test and observe the colony counts. The microbial control test for yeast, Aspergillus Niger, and Aspergillus Flavus is implemented in the nanosilver colloid. In addition to Aspergillus flavus, an Ag+ concentration of 16 ppm is enough to inhibit the growth of the samples. At the same concentration, the nanosilver colloid has a much better microbial control effect than the Ag+ standard solution, which may be because the nanoparticle can release Ag+ continuously, so the solution using the ESDM has a more significant microbial control effect.

Parameters and properties for the preparation of Cu nanocolloids containing polyvinyl alcohol using the electrical spark discharge method

Through the use of an electric discharge machine, this study performed the electrical spark discharge method in deionised water under normal temperature and pressure for Cu nanocolloid (CuNC) preparation. The CuNCs had a zeta potential of 12.3 mV, indicating poor suspension stability. The suspension stability was effectively increased (zeta potential 32.5 mV) through the addition of polyvinyl alcohol (PVA) to form PVA-containing CuNCs PVA/CuNCs. Next, the following pulse-width modulation (Ton:Toff) parameters were tested to determine the optimal setting for PVA/CuNC preparation: 10:10, 30:30, 50:50, 70:70 and 90:90 µs. The optimal preparation parameter was then determined according to the absorbance, zeta potential and size distribution results. Finally, the surface properties and crystal structure of the PVA/CuNCs were characterised through transmission electron microscopy (TEM) and X-ray diffraction (XRD). When the Ton:Toff was set to 30:30 µs, preparation efficiency was optimal, as was suspension stability, as indicated by the absorbance value (0.534), zeta potential (32.5 mV) and size distribution (85.47 nm). Transmission electron microscopy revealed that Cu nanoparticles that were more dispersed in the PVA/CuNCs had a diameter smaller than 10 nm and a crystal line width of 0.2028 nm. X-ray diffraction showed that the PVA/CuNCs contained intact Cu crystal structures.

Deriving Optimized PID Parameters of Nano-Ag Colloid Prepared by Electrical Spark Discharge Method

Using the electrical spark discharge method, this study prepared a nano-Ag colloid using self-developed, microelectrical discharge machining equipment. Requiring no additional surfactant, the approach in question can be used at the ambient temperature and pressure. Moreover, this novel physical method of preparation produced no chemical pollution. This study conducted an in-depth investigation to establish the following electrical discharge conditions: gap electrical discharge, short circuits, and open circuits. Short circuits affect system lifespan and cause electrode consumption, resulting in large, non-nanoscale particles. Accordingly, in this study, research for and design of a new logic judgment circuit set was used to determine the short-circuit rate. The Ziegler–Nichols proportional–integral–derivative (PID) method was then adopted to find optimal PID values for reducing the ratio between short-circuit and discharge rates of the system. The particle size, zeta potential, and ultraviolet spectrum of the nano-Ag colloid prepared using the aforementioned method were also analyzed with nanoanalysis equipment. Lastly, the characteristics of nanosized particles were analyzed with a transmission electron microscope. This study found that the lowest ratio between short-circuit rates was obtained (1.77%) when PID parameters were such that Kp was 0.96, Ki was 5.760576, and Kd was 0.039996. For the nano-Ag colloid prepared using the aforementioned PID parameters, the particle size was 3.409 nm, zeta potential was approximately −46.8 mV, absorbance was approximately 0.26, and surface plasmon resonance was 390 nm. Therefore, this study demonstrated that reducing the short-circuit rate can substantially enhance the effectiveness of the preparation and produce an optimal nano-Ag colloid.

Parameter control and property analysis in the preparation of platinum iodide nanocolloids through the electrical spark discharge method

This study employed the electrical spark discharge method to prepare platinum iodide nanocolloids at normal temperature and pressure.