Strength and Ductility of Ultrafine Grained Metallic Materials

2013 ◽  
pp. 557-566
Author(s):  
Yuri Estrin ◽  
Hyoung Seop Kim
Keyword(s):  
Metallic Materials ◽  
Ultrafine Grained ◽  
Strength And Ductility

The Processing of Ultrafine-Grained Materials Using High-Pressure Torsion

2007 ◽  
Vol 558-559 ◽  
pp. 1283-1294 ◽  
Author(s):  
Cheng Xu ◽  
Z. Horita ◽  
Terence G. Langdon
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
High Pressure ◽  
High Pressure Torsion ◽  
Metallic Materials ◽  
Grain Sizes ◽  
Ultrafine Grained ◽  
Wide Range ◽  
Ultrafine Grained Materials ◽  
Thin Disks

It is now well-established that processing through the application of severe plastic deformation (SPD) leads to a significant reduction in the grain size of a wide range of metallic materials. This paper examines the fabrication of ultrafine-grained materials using high-pressure torsion (HPT) where this process is attractive because it leads to exceptional grain refinement with grain sizes that often lie in the nanometer or submicrometer ranges. Two aspects of HPT are examined. First, processing by HPT is usually confined to samples in the form of very thin disks but recent experiments demonstrate the potential for extending HPT also to bulk samples. Second, since the strains imposed in HPT vary with the distance from the center of the disk, it is important to examine the development of inhomogeneities in disk samples processed by HPT.

Phase Mixture Models for Metallic Materials with Submicrometer Grain Size

2003 ◽  
Vol 791 ◽  
Author(s):  
Yuri Estrin ◽  
Hyoung Seop Kim ◽  
Mark Bush
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Mixture Models ◽  
Cell Walls ◽  
Mechanical Response ◽  
Metallic Materials ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
Model Predictions ◽  
Phase Mixture

ABSTRACTPhase mixture models describing the mechanical properties of submicrometer grained metals are presented. In this approach, grain boundaries or cell walls are treated as a separate phase. Two cases are considered: the mechanical response of an ultrafine grained material and the process of grain refinement by equal channel angular pressing. Model predictions with regard to the evolution of the microstructure, strength and texture are verified for Cu.

Analysis of precipitates in ultrafine-grained metallic materials

2018 ◽  
Vol 99 (1) ◽  
pp. 73-91 ◽  
Author(s):  
V.D. Sitdikov ◽  
R.K. Islamgaliev ◽  
M.A. Nikitina ◽  
G.F. Sitdikova ◽  
K. X. Wei ◽  
...  
Keyword(s):  
Metallic Materials ◽  
Ultrafine Grained

Grain Refinement of Copper Alloys by Equal Channel Angular Pressing

2004 ◽  
Vol 449-452 ◽  
pp. 177-180 ◽  
Author(s):  
Cha Yong Lim ◽  
Jae Hyuck Jung ◽  
Seung Zeon Han
Keyword(s):  
Grain Size ◽  
Equal Channel Angular Pressing ◽  
Copper Alloys ◽  
Metallic Materials ◽  
Fine Grained ◽  
Angular Pressing ◽  
Fine Grain ◽  
Transmission Electron ◽  
Ultrafine Grained ◽  
Average Grain Size

The equal channel angular pressing (ECAP) is one of the methods to refine the grain size of metallic materials. This study investigates the effect of ECAP process on the formation of the fine grain size in oxygen free Cu and Cu alloys. The average grain size has been refined from 150 µm before ECAP to 300 nm. Microstructure was analyzed by transmission electron micrography (TEM). The diffraction pattern of the selected area confirmed the formation of ultrafine-grained structure with high angle grain boundaries after 8 cycles of ECAP. Mechanical properties such as microhardness and tensile properties of the ultra-fine grained copper materials have been investigated.

Control of Microstructure by MaxStrain Device

2013 ◽  
Vol 762 ◽  
pp. 55-61
Author(s):  
Stan T. Mandziej ◽  
Marc Ruggeri
Keyword(s):  
Grain Refinement ◽  
Single Phase ◽  
Precipitation Hardening ◽  
Cast Alloy ◽  
Strain Rates ◽  
Metallic Materials ◽  
Plastic Deformations ◽  
Ultrafine Grained ◽  
Pure Metals ◽  
Multi Phase

Grain refinement should increase strength of metallic materials in a predictable manner. However, in applications of severe plastic deformations for this purpose, limits have been observed due to self-recovery and strain-induced precipitation assisted by generation of adiabatic heat. Pure metals and single-phase alloys have not been the best candidates for achieving ultrafine-grained microstructures therefore more often precipitation-hardening multi-phase alloys have been used in SPD experiments. To generate ultrafine-grained microstructures by accumulated multiple compressive strains executed at various strain rates during programmed thermal cycles the MaxStrainTM device was developed for GleebleTM physical simulator. This paper deals with processing of Al-6061 wrought alloy and Al-319 cast alloy by the MaxStrain device, and describes obtained microstructures.

Sign in / Sign up

Export Citation Format

Share Document