Interface structure in graphite-fiber-reinforced metal-matrix composites

2001 ◽  
Vol 31 (7) ◽  
pp. 692-700 ◽  
Author(s):  
Suraj P. Rawal
Keyword(s):  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Interface Structure ◽  
Matrix Composites ◽  
Graphite Fiber ◽  
Fiber Reinforced

scholarly journals Tensile and fatigue properties of fiber-reinforced metal matrix composites Cf/5056Al

2021 ◽  
Vol 30 ◽  
pp. 2633366X2092971
Author(s):  
Ying Ba ◽  
Shu Sun
Keyword(s):  
Metal Matrix Composites ◽  
Metal Matrix ◽  
High Strength ◽  
Longitudinal Direction ◽  
Fatigue Properties ◽  
Matrix Composites ◽  
Weak Interface ◽  
Fiber Reinforced ◽  
Alloy Matrix ◽  
Medium Strength

Fiber-reinforced metal matrix composites have mechanical properties highly dependent on directions, possessing high strength and fatigue resistance in fiber longitudinal direction achieved by weak interface bonding. However, the disadvantage of weak interface combination is the reduction of transversal performances. In this article, tensile and fatigue properties of carbon fiber-reinforced 5056 aluminum alloy matrix (Cf/5056Al) composite under the condition of medium-strength interface combination are carried out. The fatigue damage mechanisms of Cf/5056Al composite under tension–tension and tension–compression loads are not the same, but the fatigue life curves are close, which may be the result of the medium-strength interface combination.

Damage of Short-Fiber-Reinforced Metal Matrix Composites Considering Cooling and Thermal Cycling

1999 ◽  
Vol 122 (2) ◽  
pp. 203-208 ◽  
Author(s):  
Chuwei Zhou ◽  
Wei Yang ◽  
Daining Fang
Keyword(s):  
Thermal Cycling ◽  
Metal Matrix Composites ◽  
Stress Drop ◽  
Metal Matrix ◽  
Failure Modes ◽  
Short Fiber ◽  
Uniaxial Tensile ◽  
Matrix Composites ◽  
Fiber Reinforced ◽  
Matrix Damage

Mechanical properties and damage evolution of short-fiber-reinforced metal matrix composites (MMC) are studied under a micromechanics model accounting for the history of cooling and thermal cycling. A cohesive interface is formulated in conjunction with the Gurson-Tvergaard matrix damage model. Attention is focused on the residual stresses and damages by the thermal mismatch. Substantial stress drop in the uniaxial tensile response is found for a computational cell that experienced a cooling process. The stress drop is caused by debonding along the fiber ends. Subsequent thermal cycling lowers the debonding stress and the debonding strain. Micromechanics analysis reveals three failure modes. When the thermal histories are ignored, the cell fails by matrix damage outside the fiber ends. With the incorporation of cooling, the cell fails by fiber end debonding and the subsequent transverse matrix damage. When thermal cycling is also included, the cell fails by jagged debonding around the fiber tops followed by necking instability of matrix ligaments. [S0094-4289(00)01202-0]

Elastothermodynamic Damping of Fiber-Reinforced Metal-Matrix Composites

1995 ◽  
Vol 62 (2) ◽  
pp. 441-449 ◽  
Author(s):  
K. B. Milligan ◽  
V. K. Kinra
Keyword(s):  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Axial Strain ◽  
Second Law Of Thermodynamics ◽  
Infinite Matrix ◽  
Matrix Composites ◽  
Fiber Reinforced ◽  
Continuous Fiber ◽  
Finite Matrix ◽  
Starting Point

Recently, taking the second law of thermodynamics as a starting point, a theoretical framework for an exact calculation of the elastothermodynamic damping in metal-matrix composites has been presented by the authors (Kinra and Milligan, 1994; Milligan and Kinra, 1993). Using this work as a foundation, we solve two canonical boundary value problems concerning elastothermodynamic damping in continuous-fiber-reinforced metal-matrix composites: (1) a fiber in an infinite matrix, and (2) using the general methodology given by Bishop and Kinra (1993), a fiber in a finite matrix. In both cases the solutions were obtained for the following loading conditions: (1) uniform radial stress and (2) uniform axial strain.

Sign in / Sign up

Export Citation Format

Share Document