NONLINEAR BEHAVIOR OF A TYPICAL AIRFOIL SECTION WITH CONTROL SURFACE FREEPLAY: A NUMERICAL AND EXPERIMENTAL STUDY

1997 ◽  
Vol 11 (1) ◽  
pp. 89-109 ◽  
Author(s):  
M.D. Conner ◽  
D.M. Tang ◽  
E.H. Dowell ◽  
L.N. Virgin
Keyword(s):  
Experimental Study ◽  
Nonlinear Behavior ◽  
Control Surface ◽  
Airfoil Section

Nonlinear response of airfoil section with control surface freeplay to gust loads

AIAA Journal ◽  
2000 ◽  
Vol 38 ◽  
pp. 1543-1557 ◽  
Author(s):  
Deman Tang ◽  
Denis Kholodar ◽  
Earl H. Dowell
Keyword(s):  
Nonlinear Response ◽  
Control Surface ◽  
Airfoil Section ◽  
Gust Loads

Experimental Investigation on the Use of Bispectral Analysis in Detecting Nonlinear Faults in Hydraulic Machines

2014 ◽  
Vol 606 ◽  
pp. 147-151 ◽  
Author(s):  
M.S. Somia Alfatih ◽  
M. Salman Leong ◽  
L.M. Hee
Keyword(s):  
Experimental Study ◽  
Experimental Investigation ◽  
Signal Processing ◽  
Spectral Analysis ◽  
Centrifugal Pump ◽  
Nonlinear Behavior ◽  
Suction Side ◽  
Bispectral Analysis ◽  
Detection And Identification ◽  
Hydraulic Machines

Bispectral analysis is one of the relatively more recent tools in signal processing used for detection and identification of higher harmonics in a signal. It is also acknowledged to be one of Higher Order Spectral Analysis (HOSA) effective tools for detecting nonlinear behavior in mechanical systems. In this study, vibration sources in a hydraulic machine which may have features of nonlinear behavior were investigated. An experimental study was undertaken to formulate a more sensitive and effective method using Bispectral analysis to diagnose cavitation in a centrifugal pump facility. Cavitation was induced on the suction side of the pump. The cavitation signal was analyzed with and without induced cavitation conditions at different locations on the pump, and analyzed using FFT and bispectrum methods. It was observed that bispectral analysis could be used as an early indicator of cavitation with changes for severity of cavitation.

An Experimental Study of Nonlinear Behavior of Graphite/Epoxy Laminate under a Three-Point Bending Test

2021 ◽  
Vol 900 ◽  
pp. 9-15
Author(s):  
Mouad Bellahkim ◽  
Youssef Benbouras ◽  
Aziz Maziri ◽  
El Hassan Mallil ◽  
Jamal Echaabi
Keyword(s):  
Experimental Study ◽  
Failure Modes ◽  
Nonlinear Behavior ◽  
Bending Test ◽  
Three Point Bending ◽  
Digital Microscope ◽  
Layer Orientation ◽  
Bending Behavior ◽  
The Relationship ◽  
Geometrical Dimensions

In this work, an attempt has been made to study the experimental of behavior for carbon/epoxy woven laminates under a three-point bending test by varying the support span and the geometrical dimensions of the specimens. Two principles stacking sequences are studied ([45 / 0]2s & [90 / 0]6 ) to observe the effect of the layer orientation in the failure modes. This study has allowed us to confirm the relationship between the bending behavior of the specimens and the span-to-thickness ratio (l/h). Finally, a digital microscope was selected in order to characterize the succession of the failure and the failure modes, mainly the delamination damage.

Sign in / Sign up

Export Citation Format

Share Document