Damping Ratios of Reinforced Concrete Structures Under Actual Ground Motion Excitations

The use of nonlinear dynamic analysis provides significant uncertainties on the seismic demand, especially when recorded ground motions are used. As these uncertainties strongly depend on ground motion selection and modification (GMSM) methods, a spectrum-compatibility criterion and a method based on the minimization of the scaling factor are compared in this work. The variability of a representative engineering demand parameter (EDP), obtained by subjecting ten reinforced concrete structures to different groups of records, is investigated through a sensitivity study based on the “Tornado diagram analysis.” The results show that the variability of the structural demand produced by the variation of the ground motion profile amplifies significantly with the increase in complexity and irregularity of the structures. More specifically, for regular structures, the selected GMSM criteria provide very similar variability while with the increase of irregularities, the spectrum-compatibility criterion produces a minimization of the demand uncertainty.

Download Full-text

The effect of different earthquake ground motion level on performance of reinforced-concrete structures

Bitlis Eren University Journal of Science and Technology ◽

10.17678/beuscitech.952812 ◽

2021 ◽

Author(s):

Ercan IŞIK ◽

Eyyüp DEMİRKRAN

Keyword(s):

Reinforced Concrete ◽

Ground Motion ◽

Concrete Structures ◽

Earthquake Ground Motion ◽

Reinforced Concrete Structures

Download Full-text

Design of precast reinforced concrete structures of frame buildings: a new set of rules

Promyshlennoe i Grazhdanskoe Stroitel stvo ◽

10.33622/0869-7019.2019.04.04-09 ◽

2019 ◽

pp. 4-9 ◽

Cited By ~ 1

Keyword(s):

Reinforced Concrete ◽

Concrete Structures ◽

Reinforced Concrete Structures ◽

Building Frames ◽

Fine Grained ◽

Rigid Frame ◽

Floor Slabs ◽

Frame Buildings ◽

Spatial System ◽

Precast Elements

Currently, prefabricated reinforced concrete structures are widely used for the construction of buildings of various functional purposes. In this regard, has been developed SP 356.1325800.2017 "Frame Reinforced Concrete Prefabricated Structures of Multi-Storey Buildings. Design Rules", which establishes requirements for the calculation and design of precast reinforced concrete structures of frame buildings of heavy, fine-grained and lightweight structural concrete for buildings with a height of not more than 75 m. The structure of the set of rules consists of eight sections and one annex. The document reviewed covers the design of multi-story framed beam structural systems, the elements of which are connected in a spatial system with rigid (partially compliant) or hinged joints and concreting of the joints between the surfaces of the abutting precast elements. The classification of structural schemes of building frames, which according to the method of accommodation of horizontal loads are divided into bracing, rigid frame bracing and framework, is presented. The list of structural elements, such as foundations, columns, crossbars, ribbed and hollow floor slabs and coatings, stiffness elements and external enclosing structures is given; detailed instructions for their design are provided. The scope of the developed set of rules includes all natural and climatic zones of the Russian Federation, except seismic areas with 7 or more points, as well as permafrost zones.

Download Full-text

Improvement Of Curvilinear Diagrams Of Concrete Deformation

Promyshlennoe i Grazhdanskoe Stroitel stvo ◽

10.33622/0869-7019.2019.08.99-104 ◽

2019 ◽

pp. 99-104

Keyword(s):

Reinforced Concrete ◽

Peak Load ◽

Experimental Studies ◽

Concrete Structures ◽

Deformation Model ◽

Reinforced Concrete Structures ◽

Significant Difference ◽

Deformation Diagrams

Problems when calculating reinforced concrete structures based on the concrete deformation under compression diagram, which is presented both in Russian and foreign regulatory documents on the design of concrete and reinforced concrete structures are considered. The correctness of their compliance for all classes of concrete remains very approximate, especially a significant difference occurs when using Euronorm due to the different shape and sizes of the samples. At present, there are no methodical recommendations for determining the ultimate relative deformations of concrete under axial compression and the construction of curvilinear deformation diagrams, which leads to limited experimental data and, as a result, does not make it possible to enter more detailed ultimate strain values into domestic standards. The results of experimental studies to determine the ultimate relative deformations of concrete under compression for different classes of concrete, which allowed to make analytical dependences for the evaluation of the ultimate relative deformations and description of curvilinear deformation diagrams, are presented. The article discusses various options for using the deformation model to assess the stress-strain state of the structure, it is concluded that it is necessary to use not only the finite values of the ultimate deformations, but also their intermediate values. This requires reliable diagrams "s–e” for all classes of concrete. The difficulties of measuring deformations in concrete subjected to peak load, corresponding to the prismatic strength, as well as main cracks that appeared under conditions of long-term step loading are highlighted. Variants of more accurate measurements are proposed. Development and implementation of the new standard GOST "Concretes. Methods for determination of complete diagrams" on the basis of the developed method for obtaining complete diagrams of concrete deformation under compression for the evaluation of ultimate deformability of concrete under compression are necessary.

Download Full-text