Improved Quality of Drilled Holes in Laminated Carbon Fiber Reinforced Plastics via Laser-Preprocessing

2013 ◽  
pp. 27-31 ◽  
Author(s):  
F. Schneider ◽  
B. Kirsch ◽  
M. Gurka ◽  
T. Hermann ◽  
J. A. L’huiller ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Fiber Reinforced ◽  
Carbon Fiber Reinforced Plastics ◽  
Reinforced Plastics ◽  
Fiber Reinforced Plastics ◽  
Carbon Fiber Reinforced

scholarly journals Performance of 3D-Printed Continuous-Carbon-Fiber-Reinforced Plastics with Pressure

Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 471 ◽  
Author(s):  
Jun Zhang ◽  
Zude Zhou ◽  
Fan Zhang ◽  
Yuegang Tan ◽  
Yiwen Tu ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Carbon Fiber ◽  
Bending Strength ◽  
Fiber Reinforced ◽  
Carbon Fiber Reinforced Plastics ◽  
Reinforced Plastics ◽  
Continuous Carbon Fiber ◽  
Fiber Reinforced Plastics ◽  
Carbon Fiber Reinforced

Fused Deposition Modeling (FDM) has been investigated as a low-cost manufacturing method for fiber-reinforced composites. The traditional and mature technology for manufacturing continuous-carbon-fiber-reinforced plastics is Automated Fiber Placement (AFP), which uses a consolidation roller and an autoclave process to improve the quality of parts. Compared to AFP, FDM is simple in design and operation but lacks the ability to pressurize and heat the model. In this work, a novel method for printing continuous carbon-fiber-reinforced plastics with a pressure roller was investigated. First, the path processing of the pressure roller was researched, which will reduce the number of rotations of the pressure roller and increase the service life of the equipment and the efficiency of printing. Thereafter, three specimens were printed under different pressures and the tensile and bending strength of specimens were tested. The tensile strength and bending strength of specimens were enhanced to 644.8 MPa and 401.24 MPa by increasing the pressure, compared to the tensile strength and bending strength of specimens without pressure of 109.9 MPa and 163.13 MPa. However, excessive pressure will destroy the path of the continuous carbon fiber (CCF) and the surface quality of the model, and may even lead to printing failure.

scholarly journals Surface Quality of Staggered PCD End Mill in Milling of Carbon Fiber Reinforced Plastics

2017 ◽  
Vol 7 (2) ◽  
pp. 199 ◽  
Author(s):  
Guangjun Liu ◽  
Hongyuan Chen ◽  
Zhen Huang ◽  
Fei Gao ◽  
Tao Chen
Keyword(s):  
Carbon Fiber ◽  
Surface Quality ◽  
Fiber Reinforced ◽  
End Mill ◽  
Carbon Fiber Reinforced Plastics ◽  
Reinforced Plastics ◽  
Fiber Reinforced Plastics ◽  
Carbon Fiber Reinforced

scholarly journals Quality of Drilled and Milled Rivet Holes in Carbon Fiber Reinforced Plastics

Procedia CIRP ◽  
2014 ◽  
Vol 24 ◽  
pp. 56-61 ◽  
Author(s):  
Jan C. Aurich ◽  
Benjamin Kirsch ◽  
Christopher Müller ◽  
Lukas Heberger
Keyword(s):  
Carbon Fiber ◽  
Fiber Reinforced ◽  
Carbon Fiber Reinforced Plastics ◽  
Reinforced Plastics ◽  
Fiber Reinforced Plastics ◽  
Carbon Fiber Reinforced

INCREASING SENSITIVITY OF EDDY CURRENT NON-DESTRUCTIVE TESTING OF DELAMINATION IN CARBON-FIBER REINFORCED PLASTICS

2021 ◽  
pp. 28-37
Author(s):  
P. N. Shkatov ◽  
G. A. Didin ◽  
A. A. Ermolaev
Keyword(s):  
Carbon Fiber ◽  
Eddy Current ◽  
Calculation Model ◽  
Fiber Reinforced ◽  
Destructive Testing ◽  
Carbon Fiber Reinforced Plastics ◽  
Reinforced Plastics ◽  
Fiber Reinforced Plastics ◽  
Carbon Fiber Reinforced ◽  
The Difference

The paper is concerned with increasing sensitivity of eddy current nondestructive testing of most dangerous delamination in carbon-fiber reinforced plastics (CFRP). Increased sensitivity is achieved by separate registration and comparison of eddy current signals obtained from a set of stratifications of carbon fibers with the same orientation. The separation of eddy current signals is possible due to pronounced anisotropy of the electrical conductivity of the layers dominant in the direction of the fibers of the corresponding layer. Eddy-current signals are registered by eddy current probes with maximum sensitivity in a given angular direction. Prior to the scan eddy current signals of the probe are leveled on a defect-free area. The influence of the working gap on the difference between the eddy current signals of the probe is suppressed by normalizing it according to one of the signals. The analysis of the registered signals from delamination has been performed using an approximate calculation model. The reliability of the obtained results has been confirmed by comparison with experimental results and calculations using the finite element method.

Sign in / Sign up

Export Citation Format

Share Document