Analysis of Temperature Impact on Production Process with Focus on Data Integration and Transformation

2017 ◽  
pp. 317-325 ◽  
Author(s):  
Michal Kebisek ◽  
Lukas Spendla ◽  
Pavol Tanuska
Keyword(s):  
Data Integration ◽  
Production Process ◽  
Temperature Impact

TEM comparison of osmium vs osmium with potassium ferricyanide secondary fixatives and the impact of secondary fixative temperature on tissue preservation/contrast quality

1996 ◽  
Vol 54 ◽  
pp. 910-911
Author(s):  
J. W. Horn ◽  
B. J. Dovey-Hartman ◽  
V. P. Meador
Keyword(s):  
Osmium Tetroxide ◽  
Potassium Ferricyanide ◽  
Electron Microscopic ◽  
Transmission Electron ◽  
Microscopic Evaluation ◽  
Cacodylate Buffer ◽  
Transmission Electron Microscopic ◽  
Glutaraldehyde Solution ◽  
Temperature Impact ◽  
The Impact

Osmium tetroxide (OsO4) is a universally used secondary fixative for routine transmission electron microscopic evaluation of biological specimens. Use of OsO4 results in good ultrastructural preservation and electron density but several factors, such as concentration, length of exposure, and temperature, impact overall results. Potassium ferricyanide, an additive used primarily in combination with OsO4, has mainly been used to enhance the contrast of lipids, glycogen, cell membranes, and membranous organelles. The purpose of this project was to compare the secondary fixative solutions, OsO4 vs. OsO4 with potassium ferricyanide, and secondary fixative temperature for determining which combination gives optimal ultrastructural fixation and enhanced organelle staining/contrast.Fresh rat liver samples were diced to ∼1 mm3 blocks, placed into porous processing capsules/baskets, preserved in buffered 2% formaldehyde/2.5% glutaraldehyde solution, and rinsed with 0.12 M cacodylate buffer (pH 7.2). Tissue processing capsules were separated (3 capsules/secondary fixative.solution) and secondarily fixed (table) for 90 minutes. Tissues were buffer rinsed, dehydrated with ascending concentrations of ethanol solutions, infiltrated, and embedded in epoxy resin.

Optimization of the production process of special purpose pasta with the addition of carrots and pectin

2019 ◽  
Vol 28 (9) ◽  
pp. 50-53
Author(s):  
N.N. Martynov ◽  
◽  
G.A. Sidorenko ◽  
G.B. Zinyukhin ◽  
E.Sh. Maneeva ◽  
...  
Keyword(s):  
Production Process

IMPLEMENTASI JOB ORDER COSTING METHOD DALAM PERHITUNGAN HARGA POKOK PRODUKSI MAP

2018 ◽  
Vol 4 (2) ◽  
pp. 43-55
Author(s):  
Ika Yulianti ◽  
Endah Masrunik ◽  
Anam Miftakhul Huda ◽  
Diana Elvianita
Keyword(s):  
Production Process ◽  
Quantitative Data ◽  
Production Cost ◽  
Qualitative Data ◽  
Cost Data ◽  
Method Calculation ◽  
Cost Of Production ◽  
The Right ◽  
The Cost

This study aims to find a comparison of the calculation of the cost of goods manufactured in the CV. Mitra Setia Blitar uses the company's method and uses the Job Order Costing (JOC) method. The method used in this study is quantitative. The types of data used are quantitative and qualitative. Quantitative data is in the form of map production cost data while qualitative data is in the form of information about map production process. The result of calculating the cost of production of the map between the two methods results in a difference of Rp. 306. Calculation using the company method is more expensive than using the Job Order Costing method. Calculation of cost of goods manufactured using the company method is Rp. 2,205,000, - or Rp. 2,205, - each unit. While using the Job Order Costing (JOC) method is Rp. 1,899,000, - or Rp 1,899, - each unit. So that the right method used in calculating the cost of production is the Job Order Costing (JOC) method

Improving the methods to improve the stability of hydrotechnical structures in Yakutia

2020 ◽  
pp. 37-39
Author(s):  
M LOSKIN
Keyword(s):  
Agricultural Production ◽  
Hydraulic Engineering ◽  
Process Water ◽  
Small Rivers ◽  
Limiting Factor ◽  
Safe Operation ◽  
Central Yakutia ◽  
Agricultural Water Supply ◽  
Temperature Impact ◽  
The Stability

Problems of providing the population and agricultural production by qualitative potable and process water in the Central Yakutia are covered. This territory belongs to the region with acute shortage of water resources which is always a limiting factor of development of agricultural production. For the solution of this burning issue in the 80th years of the last century along the small rivers the systems of hydraulic engineering constructions providing requirements with process water practically of all settlements of the Central Yakutia were constructed. At a construction of all hydraulic engineering buildings the method of construction with preservation of soils of the basis of constructions in a frozen state was applied. When warming the climate which is observed in recent years hydraulic engineering constructions built in regions of a wide spread occurance of breeds of an ice complex and with the considerable volume of water weight, were especially vulnerable. On character and a design they experience continuous threat of damage and demand very attentive relation from the operating organizations. Taking this into account, safe operation of hydraulic engineering constructions in a zone of distribution of permafrost breeds demands new approaches. The article examines features of hydraulic engineering constructions’ operation of agricultural water supply objects in the Central Yakutia. Distinctiveness of hydraulic engineering constructions’ operation is that stability of constructions is intimately bound to temperature impact of a reservoir on ground dams’ body and the basis of constructions. The possibility of inclusion of ways for an intensification of a freezing of constructions in the structure of operational actions is studied. The new method on safe operation of hydraulic engineering constructions as prewinter abatement of the water level in a reservoir accounting volumes and norms of water consumption of the settlement is offered.

Sign in / Sign up

Export Citation Format

Share Document