Determination of High-Resolution, Sequence-Dependent DNA Duplex Structures in Solution

1994 ◽  
pp. 335-348
Author(s):  
Thomas L. James ◽  
Karl D. Bishop ◽  
Forrest Blocker ◽  
Carlos Gonzalez ◽  
Anil Kumar ◽  
...  
Keyword(s):  
High Resolution ◽  
Dna Duplex ◽  
Sequence Dependent

High-resolution microscopy of twin boundaries in gold

1987 ◽  
Vol 45 ◽  
pp. 260-261
Author(s):  
William Krakow ◽  
David A. Smith
Keyword(s):  
High Resolution ◽  
Specimen Preparation ◽  
Gold Films ◽  
Boundary Area ◽  
Transmission Electron ◽  
Recent Developments ◽  
Tilt Boundaries ◽  
High Resolution Microscopy ◽  
Twist Boundaries

Recent developments in specimen preparation, imaging and image analysis together permit the experimental determination of the atomic structure of certain, simple grain boundaries in metals such as gold. Single crystal, ∼125Å thick, (110) oriented gold films are vapor deposited onto ∼3000Å of epitaxial silver on (110) oriented cut and polished rock salt substrates. Bicrystal gold films are then made by first removing the silver coated substrate and placing in contact two suitably misoriented pieces of the gold film on a gold grid. Controlled heating in a hot stage first produces twist boundaries which then migrate, so reducing the grain boundary area, to give mixed boundaries and finally tilt boundaries perpendicular to the foil. These specimens are well suited to investigation by high resolution transmission electron microscopy.

High-Resolution Image Simulation of a Tilted Crystal

1990 ◽  
Vol 48 (1) ◽  
pp. 68-69
Author(s):  
C. J. D. Hetherington
Keyword(s):  
High Resolution ◽  
Crystal Thickness ◽  
Thin Specimen ◽  
Atomic Structures ◽  
Kikuchi Lines ◽  
High Resolution Images ◽  
Final Estimate ◽  
Simulated Images ◽  
Habit Planes

Most high resolution images are not directly interpretable but must be compared with simulations based on model atomic structures and appropriate imaging conditions. Typically, the only parameters that are adjusted, in addition to the structure models, are crystal thickness and microscope defocus. Small tilts of the crystal away from the exact zone axis have only rarely been considered. It is shown here that, in the analysis of an image of a silicon twin intersection, the crystal tilt could be accurately estimated and satisfactorily included in the simulations.The micrograph shown in figure 1 was taken as part of an HREM study of indentation-induced hexagonal silicon. In this instance, the intersection of two twins on different habit planes has driven the silicon into hexagonal stacking. However, in order to confirm this observation, and in order to investigate other defects in the region, it has been necessary to simulate the image taking into account the very apparent crystal tilt. The inability to orientate the specimen at the exact [110] zone was influenced by i) the buckling of the specimen caused by strains at twin intersections, ii) the absence of Kikuchi lines or a clearly visible Laue circle in the diffraction pattern of the thin specimen and iii) the avoidance of radiation damage (which had marked effects on images taken a few minutes later following attempts to realign the crystal.) The direction of the crystal tilt was estimated by observing which of the {111} planes remained close to edge-on to the beam and hence strongly imaged. Further refinement of the direction and magnitude of the tilt was done by comparing simulated images to experimental images in a through-focal series. The presence of three different orientations of the silicon lattice aided the unambiguous determination of the tilt. The final estimate of a 0.8° tilt in the 200Å thick specimen gives atomic columns a projected width of about 3Å.

Determination of the Activity of Pulmonary Tuberculosis: the Utility of High-Resolution Computed Tomography

2000 ◽  
Vol 42 (5) ◽  
pp. 757
Author(s):  
Myung Hee Chung ◽  
Hae Giu Lee ◽  
Won Jong Yu ◽  
Hong Jun Chung ◽  
Bo Sung Yang ◽  
...  
Keyword(s):  
Computed Tomography ◽  
High Resolution ◽  
Pulmonary Tuberculosis ◽  
High Resolution Computed Tomography

Determination of quaternary ammonium compounds in food products by the method of ultra-performance liquid chromatography/high resolution mass-spectrometry

2020 ◽  
Vol 86 (8) ◽  
pp. 23-31
Author(s):  
V. G. Amelin ◽  
D. S. Bolshakov
Keyword(s):  
Mass Spectrometry ◽  
High Resolution ◽  
Quaternary Ammonium ◽  
High Resolution Mass Spectrometry ◽  
Food Products ◽  
Quaternary Ammonium Compounds ◽  
High Resolution Mass ◽  
Ammonium Compounds ◽  
Resolution Mass

The goal of the study is developing a methodology for determination of the residual amounts of quaternary ammonium compounds (QAC) in food products by UHPLC/high-resolution mass spectrometry after water-acetonitrile extraction of the determined components from the analyzed samples. The identification and determination of QAC was carried out on an «UltiMate 3000» ultra-high-performance liquid chromatograph (Thermo Scientific, USA) equipped with a «maXis 4G» high-resolution quadrupole-time-of-flight mass spectrometric detector and an ion spray «ionBooster» source (Bruker Daltonics, Germany). Samples of milk, cheese (upper cortical layer), dumplings, pork, chicken skin and ground beef were used as working samples. Optimal conditions are specified for chromatographic separation of the mixture of five QAC, two of them being a mixture of homologues with a linear structure (including isomeric forms). The identification of QAC is carried out by the retention time, exact mass of the ions, and coincidence of the mSigma isotopic distribution. The limits for QAC detection are 0.1 – 0.5 ng/ml, the determination limits are 1 ng/ml for aqueous standard solutions. The determinable content of QAC in food products ranges within 1 – 100 ng/g. The results of analysis revealed the residual amount of QAC present in all samples, which confirms data of numerous sources of information about active use of QAC-based disinfectants in the meat and dairy industry. The correctness of the obtained results is verified by introduction of the additives in food products at a level of 10 ng/g for each QAC. The relative standard deviation of the analysis results does not exceed 0.18. The duration of the analysis is 30 – 40 min.

Sign in / Sign up

Export Citation Format

Share Document