Hertzian Contact Stress Analysis in Roller Power Transmission One-Way Clutch by Using Finite Element Analysis

2019 ◽  
pp. 621-630
Author(s):  
Karan A. Dutt ◽  
S. B. Soni ◽  
D. V. Patel
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Analysis ◽  
Contact Stress ◽  
Power Transmission ◽  
Hertzian Contact ◽  
Element Analysis ◽  
Hertzian Contact Stress

Based on ANSYS Planetary Gear Ransmission Design Analysis

2011 ◽  
Vol 314-316 ◽  
pp. 1218-1221
Author(s):  
Hao Min Huang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Contact Stress ◽  
Planetary Gear ◽  
Design Analysis ◽  
Ansys Software ◽  
Element Analysis ◽  
Planet Gear ◽  
Gear Contact ◽  
Transmission Gear

Conventional methods of design to be completed ordinary hydraulic transmission gear gearbox design, but for such a non-planet-rule entity, and the deformation of the planet-gear contact stress will have a great impact on the planet gear, it will be very difficult According to conventional design. In this paper, ANSYS software to the situation finite element analysis, the planetary gear to simulate modeling study.

Finite Element Analysis of Drum on the New Type Self-Driven Towing Machine for Cable

2011 ◽  
Vol 55-57 ◽  
pp. 664-669
Author(s):  
Jin Ning Nie ◽  
Hui Wang ◽  
De Feng Xie
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Analysis ◽  
Compressive Stress ◽  
Wire Rope ◽  
Ansys Software ◽  
Element Analysis ◽  
Structure Improvement ◽  
Improvement Measures ◽  
New Type

According to the situation that the dual-friction drums on the new type towing machine lack stress analysis when designed, the safety is difficult to test and verify. The pull of wire rope in various positions was derived and calculated, so both compressive stress and tangent friction force generated by the pull of wire rope were calculated. The result made by ANSYS software demonstrates the safety of the left drum which suffers from larger loads, structure improvement measures are put forward for the drum.

Design a Kind of Oblique-Cone-Sliding-Ring Assembly Seal Device

2014 ◽  
Vol 496-500 ◽  
pp. 1007-1011
Author(s):  
Jian Hua Fang ◽  
Wei Yan
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Work Stress ◽  
Contact Stress ◽  
Element Analysis ◽  
Ring Assembly ◽  
User Demand ◽  
Oblique Cone

The design of seal device that can be used in carbide actor is a real problems.This paper presents a kind of oblique-cone-slid-ring (OCSR) assembly seal device that can self-compensate the seal wear in application. The max contact stress on the seal surface and other contact face is far bigger than the work stress of sealed medium in carbide actor. That means the design satisfies the user demand . Keywords: oblique-cone-sliding-ring (OCSR) assembly seal; self-compensation to seal wear; finite element analysis; contact stress;

Stress Analysis and Structure Optimization for the Opening Flat Cover of Pressure Vessels

2012 ◽  
Vol 538-541 ◽  
pp. 3253-3258 ◽  
Author(s):  
Jun Jian Xiao
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Concentration ◽  
Stress Analysis ◽  
Structure Optimization ◽  
Pressure Vessels ◽  
Secondary Stress ◽  
Element Analysis ◽  
Primary Stress ◽  
Flat Cover

According to the results of finite element analysis (FEA), when the diameter of opening of the flat cover is no more than 0.5D (d≤0.5D), there is obvious stress concentration at the edge of opening, but only existed within the region of 2d. Increasing the thickness of flat covers could not relieve the stress concentration at the edge of opening. It is recommended that reinforcing element being installed within the region of 2d should be used. When the diameter of openings is larger than 0.5D (d>0.5D), conical or round angle transitions could be employed at connecting location, with which the edge stress decreased remarkably. However, the primary stress plus the secondary stress would be valued by 3[σ].

Strength-based design of a sunflower stalk cutter machine design using finite element analysis and experimental validation

2021 ◽  
pp. 095440622110597
Author(s):  
Gürkan İrsel
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Analysis ◽  
Strain Gage ◽  
Experimental Validation ◽  
Experimental Studies ◽  
Fatigue Analysis ◽  
Structural Stress ◽  
Element Analysis ◽  
Strength Based

In this study, the total algorithm of the strength-based design of the system for mass production has been developed. The proposed algorithm, which includes numerical, analytical, and experimental studies, was implemented through a case study on the strength-based structural design and fatigue analysis of a tractor-mounted sunflower stalk cutting machine (SSCM). The proposed algorithm consists of a systematic engineering approach, material selection and testing, design of the mass criteria suitability, structural stress analysis, computer-aided engineering (CAE), prototype production, experimental validation studies, fatigue calculation based on an FE model and experimental studies (CAE-based fatigue analysis), and an optimization process aimed at minimum weight. Approximately 85% of the system was designed using standard commercially available cross-section beams and elements using the proposed algorithm. The prototype was produced, and an HBM data acquisition system was used to collect the strain gage output. The prototype produced was successful in terms of functionality. Two- and three-dimensional mixed models were used in the structural analysis solution. The structural stress analysis and experimental results with a strain gage were 94.48% compatible in this study. It was determined using nCode DesignLife software that fatigue damage did not occur in the system using the finite element analysis (FEA) and experimental data. The SSCM design adopted a multi-objective genetic algorithm (MOGA) methodology for optimization with ANSYS. With the optimization solved from 422 iterations, a maximum stress value of 57.65 MPa was determined, and a 97.72 kg material was saved compared to the prototype. This study provides a useful methodology for experimental and advanced CAE techniques, especially for further study on complex stress, strain, and fatigue analysis of new systematic designs desired to have an optimum weight to strength ratio.

Temperature and Stress Analysis of Corn Kernel— Finite Element Analysis

1979 ◽  
Vol 22 (4) ◽  
pp. 0955-0960 ◽  
Author(s):  
Robert J. Gustafson ◽  
David R. Thompson ◽  
Shahab Sokhansanj
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Analysis ◽  
Corn Kernel ◽  
Element Analysis
Sign in / Sign up

Export Citation Format

Share Document