A glass melting tank furnace with barriers immersed in the batch fusion zone

1959 ◽  
Vol 16 (5) ◽  
pp. 299-299
Keyword(s):  
Tank Furnace ◽  
Fusion Zone ◽  
Glass Melting ◽  
Melting Tank

A glass melting tank furnace with two working tanks for melting crystal

1974 ◽  
Vol 31 (10) ◽  
pp. 730-733
Author(s):  
N. A. Senkevich ◽  
O. D. Khait
Keyword(s):  
Tank Furnace ◽  
Glass Melting ◽  
Melting Tank ◽  
Melting Crystal

Increasing the luminosity of the flame in a glass-melting tank furnace

1979 ◽  
Vol 36 (10) ◽  
pp. 580-582
Author(s):  
V. Ya. Dzyuzer ◽  
V. B. Kut'in ◽  
N. I. Kokarev ◽  
V. Yu. Budovkin
Keyword(s):  
Tank Furnace ◽  
Glass Melting ◽  
Melting Tank

Effect of Air Bubbling on Circulation and Heat Transfer in a Glass-Melting Tank

1986 ◽  
Vol 69 (5) ◽  
pp. 382-391 ◽  
Author(s):  
A. UNGAN ◽  
R. VISKANTA
Keyword(s):  
Heat Transfer ◽  
Glass Melting ◽  
Melting Tank

The Glass Related Properties of the SIBOR® Oxidation Protective Coating on Molybdenum Alloys

2008 ◽  
Vol 39-40 ◽  
pp. 613-618
Author(s):  
Hans Peter Martinz ◽  
Brigitte Nigg ◽  
Jiri Matej ◽  
Manfred Sulik ◽  
Heike Larcher
Keyword(s):  
Protective Coating ◽  
Glass Melting ◽  
Soda Lime ◽  
Atmospheric Plasma ◽  
Soda Lime Glass ◽  
Melting Tank ◽  
Heating Rates ◽  
Molybdenum Alloys ◽  
Opal Glass ◽  
Heating Up

The SIBOR® (Si-10B-2C) oxidation protective coating was applied onto molybdenumand molybdenum – 3 wt% zirconia samples by APS (= Atmospheric Plasma Spraying) with a subsequent heat treatment. Then the coated samples were submitted to ramp oxidation tests with heating rates of 10°C / hour up to a temperature of 1450°C. This procedure simulates the heating up of a glass melting tank where SIBOR® coated parts are most frequently used. Some of the samples which could be oxidized without any defect were then immersed in various molten glasses to determine the dissolution rate of the SIBOR® substrate system. This simulates the situation when the glass melting tank is filled and operated with molten glass. SIBOR® proved to be an excellent oxidation protective coating for the molybdenum – zirconia – material like for pure molybdenum. The coating was fairly good dissolved by opal glass and – slightly less – by soda lime glass. With borosilicate glass a much slower interaction was found. In all cases some discolouration and bubbles were found in the glasses after one week.

Intensifying the cooling of the walls of the melting tank of a glass-melting tank

1983 ◽  
Vol 40 (5) ◽  
pp. 222-226 ◽  
Author(s):  
O. N. Popov ◽  
R. Z. Fridkin ◽  
Z. T. Mamedov
Keyword(s):  
Glass Melting ◽  
Melting Tank

Change in transmission coefficient of screen glass melting in a flame tank furnace

2004 ◽  
Vol 61 (11-12) ◽  
pp. 399-401
Author(s):  
A. Balandis ◽  
G. Vaitskyalionis
Keyword(s):  
Tank Furnace ◽  
Transmission Coefficient ◽  
Glass Melting

Regenerator Checkers of Glass-Melting Tank Furnaces

1962 ◽  
Vol 21 (4) ◽  
pp. 31N-33N
Author(s):  
U. N. Nayak
Keyword(s):  
Glass Melting ◽  
Melting Tank

Prolonging the furnace campaign of glass-melting tank furnances

1979 ◽  
Vol 36 (5) ◽  
pp. 276-278
Author(s):  
O. N. Popov ◽  
A. G. Gel'mut
Keyword(s):  
Glass Melting ◽  
Melting Tank ◽  
Furnace Campaign

Limited Analysis the Operation Parameters of Float Glass Melting Tank and Flue Gas Desulfurization Correlation

2013 ◽  
Vol 361-363 ◽  
pp. 845-849
Author(s):  
Ning Xu ◽  
Yue Xu
Keyword(s):  
Flue Gas ◽  
Field Experiments ◽  
Glass Melting ◽  
Control Valve ◽  
Float Glass ◽  
Flue Gas Desulfurization ◽  
Melting Tank ◽  
Practical Operation ◽  
Complex Equipment ◽  
Operation Parameters

The float glass melting tank is huge and complex equipment which the operation parameters are difficult to control in production line. The install of desulfurizer makes the kiln more complex and unstable. In present work, we fulfill the field experiments and obtained the optimal practical operation parameters. The obtained parameters were: aperture of wings gate: 75-85%; aperture of draft fan: 30-35% for draft fan 1, and draft fan 2 were through-type; aperture of conveying fan: 70-85%; temperature of gas into desulfurizer: 180-200°C; the water flow were controlled by thermocouple and diaphragm control valve; Velocity of gas into desulfurizer: 8-10 m/s. Our results provide the guidance for installing the desulfurizer and modifying the whole system in practice.

The Effect of Flame Length on Hydrodynamics of Glass-Melting Tank in a Furnace with Horseshoe-Shaped Flame

2005 ◽  
Vol 62 (9-10) ◽  
pp. 265-271
Author(s):  
V. Ya. Dzyuzer ◽  
V. S. Shvydkii
Keyword(s):  
Glass Melting ◽  
Flame Length ◽  
Melting Tank
Sign in / Sign up

Export Citation Format

Share Document