Comparative study on the conversion of Acacia mangium wood sawdust-derived xylose-containing acid hydrolysate to furfural by sulfonated solid catalysts prepared from different lignocellulosic biomass residues

Author(s):  
Nguyen Hoang Chung ◽  
Le Quang Dien ◽  
Nguyen Thi Que ◽  
Nguyen Trung Thanh ◽  
Giang Thi Phuong Ly
2020 ◽  
Vol 102 ◽  
pp. 362-370 ◽  
Author(s):  
Carla S. Fermanelli ◽  
Agostina Córdoba ◽  
Liliana B. Pierella ◽  
Clara Saux

2019 ◽  
Vol 120 ◽  
pp. 166-175 ◽  
Author(s):  
Małgorzata Wilk ◽  
Aneta Magdziarz ◽  
Kandasamy Jayaraman ◽  
Monika Szymańska-Chargot ◽  
Iskender Gökalp

2019 ◽  
Vol 57 (6) ◽  
pp. 753-757 ◽  
Author(s):  
Nguyen Hoang Chung ◽  
Nguyen Thi Minh Phuong ◽  
Le Quang Dien ◽  
Nguyen Viet Khanh ◽  
Nguyen Thi Hue

Author(s):  
Nguyen Trung Thanh ◽  
Nguyen Hoang Long ◽  
Le Quang Dien ◽  
Giang Thi Phuong Ly ◽  
Phan Huy Hoang ◽  
...  

2017 ◽  
Vol 237 ◽  
pp. 57-63 ◽  
Author(s):  
Bijoy Biswas ◽  
Nidhi Pandey ◽  
Yashasvi Bisht ◽  
Rawel Singh ◽  
Jitendra Kumar ◽  
...  

2018 ◽  
Vol 3 (1) ◽  
pp. 26-36
Author(s):  
S.N. Abdul Rahman ◽  
Mimi Sakinah Abdul Munaim

Lignocellulosic biomass are plants that include forestry residue and agricultural residues that are mainly composed of cellulose, hemicelluloses and lignin. Red Meranti wood sawdust (RMWS) are one of lignocellulosic biomass that rich-cellulose content. To obtain cellulose, the pretreatments are needed to extract it from outer layer of lignin and hemicellulose by using the acid-chlorite delignification procedure aided with design of experimental from Design Expert 7.1 software. Four factors were selected in design of experiment using two level with half fraction factorial analysis were came out with total of 8 runs. The factors contributed were ratio acetic acid (AC) to RMWS (0.45 and 0.6), ratio sodium chlorite to RMWS (0.6 and 1.64), reaction time (4hr and 6hr) and temperature (55°C and 75°C). The results obtained were showed that the design model was substantial resulting with a coefficient of determination value of 0.9963. Two factors that generated the highest to the process were ratio SC to RMWS (B) and temperature (D). The percentage error between the actual and predicted value for lignin removal at 0.79% and 4.92%, which found to be less than 5%, and thus, the model was successfully validated.


2019 ◽  
Vol 7 ◽  
Author(s):  
Manuel Azuara ◽  
Nieves Latorre ◽  
José I. Villacampa ◽  
Victor Sebastian ◽  
Fernando Cazaña ◽  
...  

2015 ◽  
Vol 81 ◽  
pp. 9-18 ◽  
Author(s):  
Robinson Timung ◽  
Mood Mohan ◽  
Balaji Chilukoti ◽  
Soumya Sasmal ◽  
Tamal Banerjee ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document