Comparison of chemical vapor deposition and chemical grafting for improving the mechanical properties of carbon fiber/epoxy composites with multi-wall carbon nanotubes

2013 ◽  
Vol 48 (14) ◽  
pp. 4834-4842 ◽  
Author(s):  
Huaiping Rong ◽  
Klaus-Hermann Dahmen ◽  
Hamid Garmestani ◽  
Muhuo Yu ◽  
Karl I. Jacob
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Chemical Vapor Deposition ◽  
Carbon Fiber ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Epoxy Composites ◽  
Multi Wall Carbon Nanotubes ◽  
Chemical Grafting ◽  
Carbon Fiber Epoxy

Synthesis of Carbon Nanotubes on a Moving Substrate by Laser-Induced Chemical Vapor Deposition

2005 ◽  
Author(s):  
Kinghong Kwok ◽  
Wilson K. S. Chiu
Keyword(s):  
Carbon Nanotubes ◽  
Chemical Vapor Deposition ◽  
Deposition Rate ◽  
Vapor Deposition ◽  
Substrate Surface ◽  
Carbon Film ◽  
Chemical Vapor ◽  
Multi Wall Carbon Nanotubes ◽  
Vapor Deposition Technique ◽  
Synthesis Of Carbon Nanotubes

An open-air laser-induced chemical vapor deposition technique has been successfully used to rapidly deposit pillars of carbon nanotube forest on a moving glass substrate. A CO2 laser is used to heat a traversing fused quartz rod covered with metal particles inside a hydrocarbon environment. Pyrolysis of hydrocarbon precursor gas occurs and subsequently gives rise to the growth of multi-wall carbon nanotubes on the substrate surface. The experimental results indicate that nanotube growth kinetics and microstructure are strongly dependent on the experimental parameters such as laser power. The typical deposition rate of carbon nanotubes achieved in this study is over 50 μm/s, which is relatively high compared to existing synthesis techniques. At high power laser irradiation, carbon fibers and carbon film are formed as a result of excessive formation of amorphous carbon on the substrate. High-resolution transmission and scanning electron microscopy, and x-ray energy-dispersive spectrometry are used to investigate the deposition rate, microstructure and chemical composition of the catalytic surface and the deposited carbon nanotubes.

In Situ Growth of Carbon Nanotubes in Hydroxyapatite Matrix by Chemical Vapor Deposition

2009 ◽  
Vol 79-82 ◽  
pp. 1671-1674 ◽  
Author(s):  
Xiao Ying Lu ◽  
Hao Wang ◽  
Sheng Yi Xia ◽  
Jian Xin Wang ◽  
Jie Weng
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Biomedical Applications ◽  
Chemical Vapor ◽  
Novel Method ◽  
Biomedical Fields ◽  
Walled Cnts

Carbon nanotubes (CNTs)/hydroxyapatite (HA) nanocomposites have been successfully fabricated by a novel method for the biomedical applications, which is in situ growing CNTs in HA matrix in a chemical vapor deposition (CVD) system. The results show that it is feasible to in situ grow CNTs in HA matrix by CVD for the fabrication of CNTs/HA nanocomposites. Multi-walled CNTs with 50-80 nm in diameter have been grown in situ from HA matrix with the pretreatment of sintering at 1473K in air. The nanocomposites are composed with carbon crystals in CNTs form, HA crystallites and calcium phosphate crystallites, one of most important CaP bioceramics. And the CNTs content is about 1% proportion by weight among the composites in our experiments, which can enhance the HA mechanical properties and the CNTs content does not affect the HA performances. These CNTs/HA nanocomposites have the potential application in the biomedical fields.

Aligned Carbon Nanotubes Via Microwave Plasma Enhanced Chemical Vapor Deposition

1999 ◽  
Vol 593 ◽  
Author(s):  
H. Cui ◽  
D. Palmer ◽  
O. Zhou ◽  
B. R. Stoner
Keyword(s):  
Electron Microscopy ◽  
Carbon Nanotubes ◽  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Microwave Plasma ◽  
Chemical Vapor ◽  
Silicon Substrates ◽  
Multi Wall Carbon Nanotubes ◽  
Field Emission Properties ◽  
Transmission Electron

ABSTRACTAligned multi-wall carbon nanotubes have been grown on silicon substrates by microwave plasma enhanced chemical vapor deposition using methane/ammonia mixtures. The concentration ratio of methane/ammonia in addition to substrate temperature was varied. The morphology, structure and alignment of carbon nanotubes were studied by scanning electron microscopy and transmission electron microscopy. Both concentric hollow and bamboo-type multi-wall carbon nanotubes were observed. Growth rate, size distribution, alignment, morphology, and structure of carbon nanotubes changed with methane/ammonia ratio and growth temperature. Preliminary results on field emission properties are also presented.

Carbon Nanotubes and Nanofibers Grown by Microwave Plasma Enhanced Chemical Vapor Deposition on a Nickel Substrate

2003 ◽  
Vol 788 ◽  
Author(s):  
K. G. Belay ◽  
J Jackson ◽  
Yan Xin
Keyword(s):  
Carbon Nanotubes ◽  
Chemical Vapor Deposition ◽  
Electron Microscope ◽  
Vapor Deposition ◽  
Microwave Plasma ◽  
Chemical Vapor ◽  
Diamond Powder ◽  
Environmental Scanning ◽  
Nickel Substrate ◽  
Multi Wall Carbon Nanotubes

ABSTRACTBoth carbon nanotubes and carbon nanofibers were grown on a thick nickel substrate by means of microwave plasma enhanced chemical vapor deposition (MPECVD) process using 20% CH4 and 80% H2 at a temperature of 750°C and a pressure of 50 Torr. The substrate was pre-abraded with 1.0μm diamond powder and 15.0 μm diamond paste to increase the rate of nucleation. When the substrate is taken out of the reactor the film detaches itself completely from the nickel. Unusual outgrowth structures appear jutted on one section of the substrate in a symmetrical manner. These structures were very hard and, when analyzed using environmental scanning electron microscope (ESEM), Raman microscopy and transmission electron microscope (TEM), micro-trees and an abundance of multi wall carbon nanotubes (MWCNTs) and nanofibers were observed. An attempt to measure the hardness of the film using a nano-indenter was inconclusive due to the extreme hardness of the material produced.

Sign in / Sign up

Export Citation Format

Share Document